发光细菌法在水质综合毒性在线检测中的应用

以海洋发光细菌费氏弧菌（Vibriofischeri）作为检测生物,采用冻干菌粉快速复苏技术,研究费氏弧菌在水质检测中的最佳测试温度和有效性测试条件,并对硫酸锌等多种毒物和几种实际水样进行发光抑制作用分析。研究表明,费氏弧菌冻干粉复苏菌液保存在2～5℃条件下能有效测试7d,最佳测试温度为15℃,最佳测试时间为15min。氯化汞、硫酸锌、硫酸镉等重金属和苯胺、多菌灵、甲醛等有机毒物对费氏弧菌均具有较强的光抑制作用,也即费氏弧菌对以上毒物较为敏感,并能够连续7d保持对同一浓度硫酸锌的敏感性较为一致。对几种实际水样的测试和分析表明,以费氏弧菌为指示生物的发光细菌法能够应用于水质环境安全的综合毒性在线监测预警中。     

动态污水处理过程的多模型动态矩阵控制

针对活性污泥法污水处理系统的强耦合和动态变化特性,提出一种用于前置反硝化脱氮工艺的多模型动态矩阵(DMC)解耦控制方法;通过K-均值聚类分析法对外界入水中氨氮浓度进行聚类,获得以聚类中心为入水氨氮浓度的静态模型集合,分别设计线性DMC解耦控制器;再以当前时刻外界进水氨氮浓度和聚类中心为基本元素,构造切换函数,实现多模型切换。将该方法应用于活性污泥1号模型(ASM1)中,获得了较好的动态仿真效果。     

改进的TLI指数法及其在巢湖营养状态评价中的应用

对巢湖2000—2008年的监测数据运用SPSS做统计分析,得出叶绿素a与总氮、总磷和透明度的相关系数。通过得出的权重结果,分析出与26个湖泊的差异性,构建了改进的综合营养状态指数(TLI)评价方法,并提出评价的4个步骤。以巢湖为例,运用该方法对湖泊的营养状态进行评价,且对巢湖的富营养化程度做了年际和年内变化的综合评价,评价结果显示各营养物指标的相关关系在近30年有了较大变化,巢湖的富营养化现象已日益严重,已从轻度富营养化状态转变为中度富营养化状态。     

耐低温贫营养好氧反硝化菌群脱氮特性及安全性

针对微污染水体强化原位生物脱氮技术同时面临低温、贫营养及好氧问题,对实验室已分离筛选的贫营养好氧反硝化菌和耐低温好氧反硝化菌进行菌源重组,构建出高效耐低温贫营养好氧脱氮功能菌群T1(Y3+F3+H8)和T2(Y3+F4)。研究不同投菌量条件下菌群的脱氮特性,结果表明,投菌量对T1脱氮效果有一定影响,0.1、0.2和1.0 mg/L投量对NO3--N去除率为71%、91%和100%,总氮去除率为56%、34%和52%;T2菌群,当投量为0.2 mg/L时,对NO3--N、总氮去除率最大可达66%和59.48%。对菌群T1、T2进行生物安全性分析,采用次氯酸钠进行消毒,其生物灭活率均达到99.9%以上。     

碱式硫酸铝溶液中SO42-的测定

建立了以铬黑T为指示剂,乙二胺四乙酸二钠反滴定过量BaCl₂的碱式硫酸铝溶液中SO₄^2-的测定方法。实验确定的操作条件为：待测试样稀释后ρ（SO_4^2-）为0.025 ~0.100 g/L,BaCl₂过量率为25%~100%,并且在加入BaCl₂前将试样煮沸,三乙醇胺加入量为0.10 L/L。该法回收率在98.90%~100.72%,相对标准偏差小于1%。测定方法准确,可靠,且操作简便、快速。     

多溴联苯醚降解和分析研究进展

介绍了多溴联苯醚(PBDEs)在环境中的分布情况,综述了近年来国内外对PBDEs测定方法以及化学催化降解、生物降解和热解等PBDEs降解技术的研究进展,并对PBDEs研究的未来发展方向进行了展望。     

不同来源废水COD、TOC与Cl-的关系

通过对含盐化工废水(A)、受潮汐影响的河流水(B)、城市生活污水处理厂排水(C)、采油废水(D)4种不同来源废水进行为期15 d的采样监测,测定了其COD、TOC和Cl-浓度,分析比较了3种废水指标之间的关系,其中COD分别使用重铬酸钾法、氯气校正法和碘化钾碱性高锰酸钾法3种方法进行测定.实验结果表明,4种废水Cl-浓...     

鸟粪石沉淀法预处理高氨氮废水的镁盐研究

药剂费用一直是限制鸟粪石法处理高氨氮废水实际应用的主要因素。实验采用鸟粪石沉淀法预处理高氨氮废水,以磷酸氢二钠作为磷盐,就不同镁盐对高氨氮废水的处理效果进行了分析比较。实验结果表明,将氯化镁与氧化镁联用作为新型镁盐时,有很大的优势。在n（N）：n（P）：n（Mg）=1：1：1．5,n（MgCl2）：n（MgO）=1：2,反应时间为30min条件下,氨氮的去除率可以达到90％以上,与常规单独采用氯化镁的处理方法相比,镁盐药剂费用可节约2／3以上。     

A hybrid method for quasi-three-dimensional slope stability analysis in a municipal solid waste landfill

Limited space for accommodating the ever increasing mounds of municipal solid waste (MSW) demands the capacity of MSW landfill be maximized by building landfills to greater heights with steeper slopes. This situation has raised concerns regarding the stability of high MSW landfills. A hybrid method for quasi-three-dimensional slope stability analysis based on the finite element stress analysis was applied in a case study at a MSW landfill in north-east Spain. Potential slides can be assumed to be located within the waste mass due to the lack of weak foundation soils and geosynthetic membranes at the landfill base. The only triggering factor of deep-seated slope failure is the higher leachate level and the relatively high and steep slope in the front. The valley-shaped geometry and layered construction procedure at the site make three-dimensional slope stability analyses necessary for this landfill. In the finite element stress analysis, variations of leachate level during construction and continuous settlement of the landfill were taken into account. The "equivalent" three-dimensional factor of safety (FoS) was computed from the individual result of the two-dimensional analysis for a series of evenly spaced cross sections within the potential sliding body. Results indicate that the hybrid method for quasi-three-dimensional slope stability analysis adopted in this paper is capable of locating roughly the spatial position of the potential sliding mass. This easy to manipulate method can serve as an engineering tool in the preliminary estimate of the FoS as well as the approximate position and extent of the potential sliding mass. The result that FoS obtained from three-dimensional analysis increases as much as 50% compared to that from two-dimensional analysis implies the significance of the three-dimensional effect for this study-case. Influences of shear parameters, time elapse after landfill closure, leachate level as well as unit weight of waste on FoS were also investigated in this paper. These sensitivity analyses serve as the guidelines of construction practices and operating procedures for the MSW landfill under study.     

Carry-over of dietary organochlorine pesticides, PCDD/Fs, PCBs, and brominated flame retardants to Atlantic salmon (Salmo salar L.) fillets

Information on carry-over of contaminants from feed to animal food products is essential for appropriate human risk assessment of feed contaminants. The carry-over of potentially hazardous persistent organic pollutants (POPs) from feed to fillet was assessed in consumption sized Atlantic salmon (Salmo salar). Relative carry-over (defined as the fraction of a certain dietary POP retained in the fillet) was assessed in a controlled feeding trial, which provided fillet retention of dietary organochlorine pesticides (OCPs), dioxins (PCDD/Fs), polychlorinated biphenyls (PCBs), and brominated flame retardants (BFRs). Highest retention was found for OCPs, BFRs and PCBs (31-58%), and the lowest retentions were observed for PCDD/Fs congeners (10-34%). National monitoring data on commercial fish feed and farmed Atlantic salmon on the Norwegian market were used to provide commercially relevant feed-to-fillet transfer factors (calculated as fillet POP level divided by feed POP level), which ranged from 0.4 to 0.5, which is a factor 5-10 times higher than reported for terrestrial meat products. For the OCP with one of the highest relative carry-over, toxaphene, uptake and elimination kinetics were established. Model simulations that are based on the uptake and elimination kinetics gave predicted levels that were in agreement with the measured values. Application of the model to the current EU upper limit for toxaphene in feed (50 μg kg⁻¹) gave maximum fillet levels of 22 μg kg⁻¹, which exceeds the estimated permissible level (21 μg kg⁻¹) for toxaphene in fish food samples in Norway.