纳米TiO2/CNTs复合材料的制备及其光学性质

TiO2在碳纳米管上的复合材料可以增加材料的光催化性能,已成为新的研究热点.本文采用低温液相法成功地合成了TiO2/CNTs复合材料,并用TEM、XRD和UV-vis对材料进行了表征,结果表明,TiO2很好地分散在CNTs上,具有显著的催化效果,有很好的应用前景.     

Solid‐phase extraction and GC analyses of select agricultural pesticides and metabolites in stream water

Abstract

The occurrence of agricultural pesticides in surface waters around the USA has created a concern over the status of safe drinking water. Solid‐phase extraction (SPE) or liquid‐liquid extraction (LLE) is usually employed to concentrate trace levels of pesticides in water samples to concentrations that are measurable with advanced chromatographic instruments. We describe here a SPE and capillary gas chromatographic (GC) procedure to extract and concentrate trace levels of select agricultural pesticides and metabolites from stream water. Our SPE and GC method provides high sensitivity, with recoveries between 85% to 95%, and high reproducibility for 9 of the pesticides studied. The described method provided marginal recoveries of 19 and 60% for the atrazine metabolites.     

激发剂作用下的盐石膏废渣的水化过程

运用Kondo模型,研究了在激发剂硫酸钠作用下盐石膏废渣的水化过程.盐石膏废渣的水化过程分为3个阶段,第1、第3阶段受扩散作用控制;第2阶段受相边界反应控制.分别研究了激发剂溶液浓度和温度对相边界反应阶段水化速率的影响,结果表明,在0—0.60 mol.L-1范围内,增大激发剂溶液浓度可使水化速率常数k增大,在12℃≤...     

气相色谱仪检测溶解气H_2、He最佳观测条件的选择

通过色谱柱、固定相以及载气流速的选择性实验 ,提高了气相色谱仪在观测地下水中H2 、He分离效能和检测效能。本文对此作介绍 ,以期对使用气相色谱仪进行地下水H2 、He观测的台站能有所启发和借鉴     

废水生化处理出水吸收SO2过程相平衡关系的确定

应用相平衡理论对吸收液－ＳＯ２体系的相平衡关系进行了系统研究,确定了吸收相平衡的数学模型,并通过试验对数学模型进行了验证,结果表明,数学模型计算值与试验实测值基本吻合。     

微生物絮凝剂处理造纸中段废水的实验研究

实验从土壤中分离筛选出1株絮凝活性较高的絮凝剂产生菌,经鉴定为1株黑曲霉.采用其产生的微生物絮凝剂M-2处理造纸中段废水,对絮凝条件进行了优化,在最佳絮凝条件下,M-2对造纸中段废水的CODcr去除率可达70.6%,浊度去除率可达91.7%,其絮凝效果优于传统的絮凝剂.     

响应面法优化养殖水体中炔雌醇的固相萃取条件

在单因素试验、Plackett-Burman设计试验基础上,采用Box-Behnken响应面法对养殖水体中炔雌醇(EE2)的固相萃取条件进行优化。结果表明,洗脱液体积、洗脱液组成和淋洗液体积是影响EE2固相萃取回收率的3个主要因素;EE2的最佳固相萃取条件为:水样pH值为3,进样流量为3.0 mL/min,淋洗液为体积分数为10%的甲醇水溶液,淋洗液体积7.0 mL,洗脱液为乙酸乙酯-正己烷混合溶液(体积比为9∶1),洗脱液体积12.0 mL。该条件下养殖水样中EE2固相萃取回收率为81.6%～86.7%。     

Blast wave clearing behavior for positive and negative phases

The purpose of the research was to improve prediction of response of buildings to blast waves by including the negative phase and considering clearing of both positive and negative phases. Commonly used structural design practices, which trace their origins to military design manuals, often ignore the negative phase as well as positive phase clearing. For high explosive threats, this approach is conservative in most circumstances. However, negative phase clearing had not previously been studied for blast waves, and the implications for structural response had not been evaluated. This paper presents results of modeling negative phase blast clearing behavior for a typical blast wave and discusses the differences from positive phase clearing. The implications of including positive and negative phase clearing in building blast damage analysis are also investigated through single-degree-of-freedom (SDOF) analyses.Blast waves from explosion sources like a vapor cloud explosion (VCE), pressure vessel burst or high explosive exhibit both positive and negative phases, and the relative magnitude of the positive and negative phases varies among explosion sources and the specific circumstances of each source. A fully reflected blast wave is produced if an incident blast wave were to strike an infinitely tall and wide wall in a normal orientation. Both the positive and negative phases of the blast wave are enhanced by the reflection process. However, when an incident blast wave strikes a wall of finite size in a normal orientation, rarefaction waves are created at the edges of the wall, and the rarefactions sweep down from the roof and inward from sides. The rarefaction waves result in a clearing effect for both the positive and negative phases.Clearing relieves some of the applied blast load on the reflected wall for the positive phase. However, this is not always the case for the negative phase. As shown by the results presented in this paper, clearing may either relieve or enhance the applied negative phase blast load, depending on the duration of the blast wave and the wall dimensions.The impact of negative phase clearing on structural response for generic building components was also investigated. Nonlinear SDOF methods were used to characterize response in terms of peak positive and negative displacements. It was found that the influence of the negative phase is significant and the peak structural response can occur during negative (outward) displacement.     

卷烟膨胀烟丝生产线冷端CO_2泵装置的优化改进

为解决干冰膨胀烟丝生产线冷端液体工艺泵因机械密封长期超压和气缚现象造成损坏发生CO2泄漏而导致紧急停机抢修的问题,对干冰膨胀线冷端工艺罐系统进行了优化改进。在工艺泵吸口前管路引一根气相平衡管至工艺罐顶部,当泵吸口前管路有CO2液体时,输送管路内气化的CO2气体通过气相平衡管线释放回工艺罐内,不会进入工艺泵体内。应用结果表明,工艺泵内的憋压和气缚现象消失了,机械密封受到保护。改造前机械密封平均一个季度更换一次,改造后机械密封使用5年未损毁,达到保护干冰膨胀线冷端工艺泵机械密封的目的。     

Analysis of trace dicyandiamide in stream water using solid phase extraction and liquid chromatography UV spectrometry

An improved method for trace level quantification of dicyandiamide in stream water has been developed. This method includes sample pretreatment using solid phase extraction. The extraction procedure (including loading, washing, and eluting) used a flow rate of 1.0 mL/min, and dicyandiamide was eluted with 20 mL of a methanol/acetonitrile mixture (V/V = 2:3), followed by pre-concentration using nitrogen evaporation and analysis with high performance liquid chromatography–ultraviolet spectroscopy (HPLC–UV). Sample extraction was carried out using a Waters Sep-Pak AC-2 Cartridge (with activated carbon). Separation was achieved on a ZIC^®-Hydrophilic Interaction Liquid Chromatography (ZIC-HILIC) (50 mm × 2.1 mm, 3.5 μm) chromatography column and quantification was accomplished based on UV absorbance. A reliable linear relationship was obtained for the calibration curve using standard solutions (R² > 0.999). Recoveries for dicyandiamide ranged from 84.6% to 96.8%, and the relative standard deviations (RSDs, n = 3) were below 6.1% with a detection limit of 5.0 ng/mL for stream water samples.