Possible Utilization of Silica Gel Sludge for the Removal of Phenol from Aqueous Solutions: Laboratory Studies

This paper discusses the adsorption capacity of silica gel sludge for phenol removal from aqueous solution. Kinetic experiments showed that phenol adsorption was completed after 2 h. Adsorption isotherms were measured for phenol from aqueous solution onto silica gel sludge under various pHs and temperatures. Results showed that the adsorption capacities for phenol was increased as pH decreased from 6.5 to 2. Temperature also was found to affect the adsorption isotherm. As temperature increases from 30 to 50°C, the adsorption capacity increases. The adsorption equilibrium of phenol on silica gel sludge was described by the linear Freundlich and Langmuir models. Furthermore, results showed that the isotherm parameters fit both linearized Langmuir and Freundlich adsorption isotherms. The Freundlich and Langmuir parameters at optimum pH was found as K _f=2.89, 1/n=0.23 and K _d=22.0, q _m=7.98, respectively. Whereas, for those at optimum temperature it was observed as K _f=2.87, 1/n=0.16 and K _d=20.93, q _m=7.91, respectively.     

炼油厂"三泥"离心脱水处理研究

通过对目前炼油厂“三泥”性状的调查，利用已有污泥处理设施进行了炼油厂“三泥”离心分离的现场试验，并分析了影响“三泥”离心分离处理工艺的主要因素，发现了离心机转速和絮凝剂投加量对“三泥”离心分离的有关规律和最佳操作条件，在此基础上，提出了适合炼油厂“三泥”处理系统的优化方案。     

活性污泥吸附重金属Cr6+的研究

以活性污泥为材料，采用不同时间、温度、pH进行吸附重金属Cr^6 的研究。实验结果表明，当吸附时间为15min，吸附温度为28℃，吸附pH=7时具有较好吸附效果。在此条件下，当重金属Cr^6 浓度为50mg/L，其吸附率可达97．2％。     

固硫剂制备工艺探讨

探讨了循环流化床锅炉脱硫方法中固硫剂的制备工艺，对几种石灰石破碎设备及工艺进行了分析比较，通过柱磨机粉磨石灰石的工业试验，了解其产品粒度分布，从而择优确定固硫剂制备工艺流程。     

Stabilization and utilization of hospital waste as road and asphalt aggregate

This article reports the operational results of the effective utilization of hospital waste molten slag produced using a high-temperature melting system, and being operated at a hospital in Selangor, Malaysia. The hospital waste is incinerated and subsequently melted at 1200°C. Scanning election microscope (SEM)/EDX results showed that the slag produced after melting contained amounts of SiO₂, CaO, and Al₂O₃ in excess of 53%, 9%, and 16%, respectively. The results from a leaching analysis on the slag produced proved that the melting process had successfully stabilized the heavy metals. The use of this slag as an alternative material to replace conventional aggregates for road construction was studied. The results from aggregate and asphalt mix tests showed that the slag produced fulfills all the requirements of an alternative aggregate. The average asphalt content, or the optimum asphalt content to be mixed with hospital waste molten slag, was found to be about 5.53%.     

稳定同位素混合模型揭示的长江下游新石器时代人群摄食策略

长江下游地区是稻作农业的主要起源地之一。然而,水稻对长江下游新石器时代人群饮食的贡献程度仍不清晰。稳定同位素混合模型能够量化揭示长江下游地区史前人群的摄食策略。系统收集长江下游地区已发表的人骨、动物骨和植物稳定碳氮同位素数据,基于稳定同位素混合模型,对长江下游地区新石器时代人群的摄食策略进行研究。结果发现：距今7.0—5.3 ka长江下游地区人群可能摄食多种动植物资源,该时期水稻对人类饮食的贡献与其他植物资源基本相当。距今5.3—4.3 ka,水稻已超过其他动植物资源,成为美人地遗址人群的主要食物资源。研究揭示了长江下游新石器时代文明化进程与稻作农业发展具有同步性,狩猎采集经济则为该区域文明化进程起到基础支撑作用。     

混合接种PN与PN/A颗粒污泥快速启动连续流自养生物脱氮反应器

在连续流条件下,快速培养亚硝化-厌氧氨氧化（PN/A）颗粒污泥是实现污水高效生物脱氮处理的关键技术. 与PN/A污泥相比,亚硝化（PN）颗粒污泥具有生长周期短、易于批量化培养的优点,并可作为富集厌氧氨氧化菌（AMX）的载体. 在3个完全混合流反应器（R1~R3）中,分别按照质量比3∶1、1∶1和1∶3混合接种PN/A和PN颗粒污泥,并通过设置高氨氮负荷、短水力停留时间和强水力剪切条件,成功启动了连续流自养生物脱氮工艺. 结果表明,尽管R3的启动时长较R1和R2更长,但污泥接种比并未显著影响连续流反应器在稳定状态下的脱氮性能,总氮去除负荷均可达到2.6 kg·（m³·d）^-1以上. 接种的PN颗粒污泥通过提供好氧氨氧化菌种（AOB）,为AMX生长供给了充足的亚硝态氮基质,充分发挥了培养PN/A颗粒污泥的前驱体作用. 由高通量测序结果可知,R1~R3中成熟颗粒的微生物丰度和多样性指数均明显高于接种污泥. AOB（Nitrosomonas属）和AMX（Candidatus Kuenenia和Brocadia属）与Chloroflexi、Bacteroidetes和Chlorobi等异养菌门是驱动自养生物脱氮和维持颗粒结构稳定的关键菌群. 总之,PN与PN/A颗粒污泥的混合接种是快速启动连续流自养脱氮工艺的可行策略,对工程应用具有指导意义.     

生物处理过程中活性污泥对氯代芳香化合物吸附性能的研究

本文研究了邻二氯苯 和邻氯酚生物处理过程中在活性污泥上的吸附特性及影响因素。通过测定等温吸附曲线,表明这两种有机化合物在活性污泥上的吸附符合线性吸附等温式：属于在疏水键力作用下的表面物理吸附,对难溶于水的邻二氯苯具有较强的吸附能力。     

高浓度废液纳滤膜分离工艺设计

当进行高浓度废液纳滤膜分离工艺设计时,必须首先进行纳滤膜分离工艺试验,通过工艺试验确定：纳滤膜型号,完成膜的筛选工作;确定纳滤膜分离规律、分离模型、膜污染规律。利用获得的数学关系式确定主要操作运行压力、浓缩液流量、膜面积、组件数目、膜组件排列方式、冷却循环系统设计、纳滤膜污染的预测与清洗系统设计。纳滤膜清洗系统与自控系统应该根据试验结果并考虑纳滤膜生产商提供的数据进行设计。     

短程硝化—厌氧氨氧化组合工艺在脱氮领域的研究进展

基于全程硝化反硝化的传统生物脱氮工艺在硝化过程中需要大量氧气供应,反硝化过程需要有机物作为碳源,存在能耗与药耗过大的问题.为了降低废水脱氮的成本,短程硝化(PN)—厌氧氨氧化(ANAMMOX)组合工艺(PNA工艺)得到了高速发展.综述了PNA工艺的影响因素,重点介绍了4种基于PN与ANAMMOX原理开发的衍生PNA工艺...