7B04铝合金和30CrMnSiA钢短期腐蚀的电化学行为研究

目的研究7B04铝合金和30CrMnSiA合金钢试样的电化学性能。方法采用电化学实验、扫描电子显微镜(SEM)、腐蚀坑深度测试分别对7B04铝合金和30CrMnSiA合金钢试样在是否经过天然海水浸泡的情况下进行测试分析,得到微观腐蚀形貌和腐蚀坑深度以及试样表面不带锈和带锈时的电化学性能。结果随着Na Cl浓度增大,7B04铝合金和30CrMnSiA钢的自腐蚀电流变大,两者之间存在明显的电位差,接触后会发生电偶腐蚀。电偶电流与阴阳极面积比和Na Cl浓度有关,阴阳极面积比增大或Na Cl浓度升高均会导致电偶效应增强。经过海水短期浸泡后,7B04铝合金表面的锈层不仅没有起到抑制腐蚀的作用,反而使自腐蚀加重,但电偶效应确实有所减弱。结论沿海设备在使用过程中应竭力避免铝合金在锈层下工作。     

无剩余污泥的多级活性生化处理工艺

介绍了多级活性生化处理 (MSABP)这项新的废水处理技术的原理、技术特点及两个实例运用。这是此项技术在国内的首次运用 ,其最大的优点是无剩余污泥产生 ,不需要沉淀池     

Application of CFD Methods for Modelling in Air Pollution Problems: Possibilities and Gaps

Different urban air pollution problems deal with complex structure of air flows and turbulence. For such problems the Computer Fluid Dynamics (CFD) methods become widely used. However, this approach despite a number of advantages has some problems. Experience of use of CFD tools for development of models and suggestions of their applications for a local scale air pollution over a complex terrain and stable stratification are discussed in this paper, including: Topography and complex geometry: choose of the co-ordinate system and computer grid; Turbulence closure for air pollution modelling: modified k- model for stable stratified ABL; Boundary conditions for vertical profiles of velocity for stable-stratified atmosphere; Effects of the radiation and thermal budget of inclined surfaces to dispersion of pollutants; Artificial sources of air dynamics and circulation.Some examples of CFD applications for air pollution modelling for a flat terrain, mountainous area, mining open cast and indoor ventilation are discussed. Modified k- model for stably-stratified ABL is suggested. Due to the isotropic character of the k- model a combination of it in vertical with the sub-grid turbulence closure in horizontal can be more suitable for ABL. An effective scheme of boundary conditions for velocity profiles, based on the developed similarity theory for stable-stratified ABL, is suggested. Alongside with the common studies of atmospheric dispersion, the CFD methods have also demonstrated a good potential for studying anthropogenic and artificial-ventilation sources of air dynamic and circulation in local-scale processes of air pollution.     

Improvement of the antifouling characteristics in a bioreactor of polypropylene microporous membrane by the adsorption of Tween 20

Surface modification by physical adsorption of Tween 20 was accomplished on polypropylene microporous membranes (PPMMs). Attenuated total reflection-Fourier transform infrared spectroscopy (ATR/FT-IR) and scanning electron microscope (SEM) were used to characterize the chemical and morphological changes on the membrane surfaces. Water contact angles and relative pure water fluxes were measured. The data showed that the hydrophilic performance for the modified membranes increased with the increase in the adsorption amount of Tween 20 onto the surface or into the pores of polypropylene microporous membranes. To test the antifouling property of the membranes by the adsorption of Tween 20 in a membrane bioreactor (MBR), filtration for active sludge was performed using synthetic wastewater. With the help of the data of water fluxes and the FE-SEM photos of the modified PPMMs before or after operating in a MBR for about 12 d, the PPMMs with monolayer adsorption of Tween 20 showed higher remained flux and stronger antifouling ability than unmodified membrane and other modification membranes studied.     

Mechanics Principle and Engineering Application of Split Layer and Bed Separation of Mining Overburden

<正>To control land surface subsidence caused the underground mineral exploitation and the catastrophic phenomena such as serious damage of buildings, waterbodies, cultivated lands, railways, bridges caused by land subsidence, bed separation grouting technology of overburden is put forward. To provide theoretical support for the technology, the characteristics and the mechanics mechanism of mining overburden from layer-split to formation of bed separation are studied. On the basis of elastic sheet board theory, calculation formula of rock sheet deflection is presented, and the mechanics criteria of the separation formation and the calculation formula of bed separation volume are set up. Finally, the applications and technics of bed separation grout technology of mining overburden to control land subsidence in china are introduced.     

两段接触氧化法处理生活污水的工程实例

本污水厂设计规模 70 0 0m3 d ,进水CODCr3 0 0mg L ,BOD515 0mg L ,SS 2 0 0mg L ,采用两段接触氧化法处理工艺 ,运行结果表明 ,出水水质达到GB8978 1996污水综合排放标准中的二级标准     

去除生活废水及污泥中病毒的研究

从生活废水中病毒的处理着手，通过实验测定病毒蚀斑形成数量(PFU)，说明了生活废水中病毒数量的非恒定性和病毒易与污泥吸附的特性，以及常规废水处理方法对它们杀灭效率的不一致性，并分析了废水处理过程中几种杀灭病毒的方法，以及它们的不同效率和杀灭病毒的原理，探讨城市污水处理中病毒去除的几种方法。     

ASM1中废水和污泥组分浓度的测定方法研究

对呼吸计量法应用于校准ASM1作了简明的阐述。在呼吸速率与模型组分关系的基础上,介绍了ASM1中废水与污泥各组分浓度的测定方法,并指出模型组分细化的意义。     

铜镍电镀污泥的资源化与无害化处理试验研究

提出了铜镍电镀污泥的资源化与无害化处理的工艺流程 ,并用试验考察了各工序的技术经济指标。试验结果表明 ,铜粉品位大于 90 % ,铜的回收率大于 95 % ,硫酸镍质量达到工业一级 ,镍回收率大于 80 % ,浸出渣和净化渣经固化处理后可作普通建筑材料使用 ,工艺过程产生的废水可以达标排放     

骆马湖的氮磷平衡及实施截污工程对水质改善效果的研究

骆马湖“九五”期间的氮磷平衡分析结果表明：氮磷在骆马湖湖体中的滞留量分别为1188.89t/a和193.36t/a。根据骆马湖的水质要求，在骆马湖截污工程完成后，没有新的污染进入水体的前提下，对骆马湖水体通过自然净化恢复到要求状态所需的时间进行了详细的数学推导和科学论证，结果表明，在不考虑底泥营养物质的情况下，只需0.19年左右的时间就能恢复，如果考虑底泥的影响。也只需0.59年左右的时间就能恢复，因此得出结论：对骆马湖实施截污是加速骆马湖水体改善的最佳途径。