城市生活垃圾机械生物处理效果

采用机械生物处理工艺研究了淋洗水解、脱水与好氧生物干燥对城市生活垃圾的处理效果。结果表明:在淋洗水解及压榨脱水机械生物处理阶段,控制淋洗液与生活垃圾重量比2:1,停留时间1.2~1.4 d条件下,生活垃圾可以减量49.7%。而过程中产生的淋滤液COD为 32 939 mg/L、pH为5.1、COD:N:P=261:5:3.6,可以进行厌氧消化处理或作为碳源进行资源化利用。在好氧生物干燥阶段,通风量采用0.08 m3/min,2~3 d堆体温度可升至73℃,7 d左右即可产出LCV高达15 000 kJ/kg左右的高品位垃圾衍生燃料(RDF),其产率为38.2%,氯元素含量低于0.5%,重金属含量较低,满足燃料要求。     

以聚己内酯作为生物反硝化固体碳源的研究

为解决水体因低碳氮比而导致脱氮效率差的问题,将颗粒聚己内酯(PCL)重新塑形为阶梯环状,研究其作为反硝化过程的生物膜载体与固相碳源的反硝化性能。结果表明,在静态实验中,平均反硝化速率为8.57 mg NO3-N/(L·h);反硝化过程为零级反应。连续填充床实验中,超过90%的硝酸盐可被去除,出水NO2-N质量浓度低于0.20 mg/L;出水NH3-N质量浓度略有上升;出水溶解性有机碳(DOC)先上升后降低至1 mg/L左右。电子扫描显微镜扫描显示,PCL阶梯环反应表面空隙率较高,表面生物膜以杆菌为主,反应后被明显腐蚀;液相色谱检测显示PCL阶梯环分子量反应前后略有下降,其结构未受到破坏;表明该材料适合作为反硝化反应的碳源的同时,又可以作为载体供微生物附着生长。     

β-环糊精接枝羧甲基壳聚糖吸附剂的制备及其性能

采用γ-氨丙基三乙氧基硅烷化学修饰活化后的硅胶,以戊二醛为交联剂,接上羧甲基壳聚糖,继而接枝上β-环糊精作为功能单体,制备了一种用于分离富集水样中Cu(Ⅱ)的固相萃取新材料。利用红外光谱(FT-IR)、比表面分析(BET)、X射线衍射光谱(XRD)以及热重分析(TG)等方法对吸附剂进行结构表征。采用火焰原子吸收(FAAS)作为检测手段,考察了溶液pH、振荡时间、吸附剂用量、样品流速、洗脱液浓度和体积等对吸附剂吸附Cu(Ⅱ)的影响。吸附剂饱和吸附容量为9.37 mg/g,最大富集倍数高达350。吸附过程能用准二级动力学模型和Langmuir等温吸附方程进行很好的拟合。应用于环境水样中Cu(Ⅱ)的分离富集与测定,回收率在96.8%~105.2%之间,效果较好。     

新制备生物炭的特性表征及其对石油烃污染土壤的吸附效果

生物炭作为一种绿色环保的功能材料因其在污水处理和污染土壤修复方面具有显著效果而受到极大关注。采用红外光谱、元素分析仪及微孔分析对不同温度(200、300、400、500和600℃)条件下制备的木屑和麦秆生物炭进行特性表征,并采用制备的生物炭净化石油污染土壤,分别考察了污染物性质、生物质原料和热解温度对其净化效果的影响。结果表明,随着热解温度的增高,生物炭芳香化程度增加,极性降低,微孔结构逐渐发育,表面积增大。加入生物炭33 d后,污染土壤中总石油烃及其组分烷烃的浓度比对照略有降低,而PAHs浓度下降显著。随着热解温度升高,2种生物炭对PAHs的吸附强度均逐渐增大,芳香度增高、表面积增大是强吸附的主要原因。2种生物炭在400℃及以下温度制备时对PAHs的吸附强度为:木屑生物炭 > 麦秆生物炭;而400℃以上温度制备的生物炭吸附强度则相反,即麦秆生物炭 > 木屑生物炭,说明生物炭原料对其吸附强度也具有显著影响。     

城市生活垃圾和污水处理厂剩余污泥混合发酵的原料配比优化研究

以城市生活垃圾和污水处理厂的剩余污泥为混合原料,研究了混合原料的不同配比对厌氧发酵过程及产气的影响。结果表明:城市生活垃圾与剩余污泥以挥发性固体(VS)质量比为2∶1混合后,厌氧发酵效果最好,累计产气量最高,达到8 721mL,发酵后的总固体(TS)、VS、COD去除率分别达43.65%、35.98%、47.88%;各实验组在发酵过程中的pH、氨氮浓度和碱度均在合理范围内,未对厌氧发酵反应造成影响;以适当配比的城市生活垃圾和剩余污泥为混合原料,进行中温联合厌氧发酵是可行的,联合厌氧发酵可以弥补单一原料的缺陷,在一定程度上改善厌氧发酵效果。     

城市生活垃圾处理现状、趋势及对策建议

通过对垃圾处理方法的全面对比以及对国内外垃圾处理现状和趋势分析,垃圾焚烧发电必将成为中国特别是人多地少的发达地区未来垃圾处理的主要方式.为最大程度地防止二次污染、避免环境纠纷,从完善相关法规、强化环评管理和日常监督管理等方面提出垃圾焚烧及发电项目控制污染的相关对策和建议.     

Compostability of Poly(lactide): Degradation in an Inert Solid Medium

Commercial poly(lactide) degradation was studied in an inert solid medium simulating compost conditions, with the aim to achieve a complete carbon balance of the polymer degradation. The mineralisation rate at the end of the test was compared to those obtained for poly(lactide) degradation in compost. It was shown that the mineralisation rate after 45 days of degradation was quite lower in inert solid medium than in compost but the standard deviation of data was enhanced. A protocol for both extraction and quantification of the carbon included in the different degradation by-products was proposed and the carbon balance of the polymer degradation was followed during the test with a satisfactory accuracy. The non-degraded PLA material was recovered during the test, hence the evolution of the glass transition temperature and the molecular weight was followed. A two-step degradation mechanism was highlighted in inert solid medium, showing the fundamental role of abiotic reactions for PLA degradation in compost.     

Waste materials for activated carbon preparation and its use in aqueous-phase treatment: a review

Commercial activated carbon is a preferred adsorbent for the removal of micropollutants from the aqueous phase; however, its widespread use is restricted due to high associated costs. To decrease treatment costs, attempts have been made to find inexpensive alternative activated carbon (AC) precursors, such as waste materials. Some reviews report the use of waste materials for the preparation of AC; however, these studies are restricted to either type of wastes, preparation procedures, or specific aqueous-phase applications. The present work reviews and evaluates literature dedicated both to the preparation of AC by recycling different types of waste materials and also to its application in various aqueous-phase treatments. It is clear that conventional (from agriculture and wood industry) and non-conventional (from municipal and industrial activities) wastes can be used to prepare AC, that can be applied in various aqueous treatment processes, namely to remove organic pollutants, dyes, volatile organic compounds, and heavy metals. Moreover, high surface areas can be obtained using either physical or chemical activation; however, combined treatments might enhance the surface properties of the adsorbent, therefore increasing its adsorption capacity. It is evident from the revision made that AC prepared from both conventional and non-conventional wastes might effectively compete with the commercial ones. This happens mostly when the activation procedures are optimized considering both the raw material used to produce the carbons and the contaminants to be removed.     

垃圾填埋场地下水污染修复技术优选研究

结合国内外地下水污染场地的修复经验,综合考虑当地社会经济条件、地下水脆弱性、污染物特征等因素,采用层次分析法建立了修复技术优化指标体系;在此基础上运用多准则决策分析模型(MCDA)进行地下水污染修复技术优选排序,构建垃圾填埋场地下水污染修复技术筛选模型;并以湖北省某简易垃圾填埋场为例进行应用研究。结果表明:在备选的5种场地地下水修复技术(监测自然衰减技术、渗透反应格栅、多相抽提技术、抽出-处理技术、原位微生物修复技术)中,抽出-处理技术、原位微生物修复技术较为理想。综合考虑该污染场地条件、地下水污染治理要求及附近受体分布情况,得到最佳修复方案为:高污染风险区域采用抽出-处理技术和原位微生物修复技术组合;低污染风险区域采用监测自然衰减技术。     

废彩色阴极射线管玻璃的X和γ射线屏蔽特性

废电视机和计算机监视器产生了数量庞大的废阴极射线管（CRTs）,已成为全球面临的环境风险,迫切需要找出新的处置方法和再利用途径来化解风险。用Χ和γ射线标准剂量测定装置(QH16),XRF,ICP,XRD和灰熔点炉等试验手段测试了废彩色CRTs玻璃的铅当量、化学组成和烧结等特性,并与钢、铁矿石、重晶石等进行对比;讨论了废彩色CRTs玻璃的X和γ射线质量衰减系数,能量吸收特性和辐射屏蔽能力。结果表明,废彩色CRTs玻璃所含的Pb、Ba、Sr、Sb、Ce、Zn等金属元素具有优良的Χ和γ射线屏蔽性能,将其通过烧结法制备成射线屏蔽材料是控制污染和再利用的有效途径。