剩余污泥热水溶性有机物的提取方法优化研究

热水溶性有机物含量和组成是表征剩余污泥(简称为污泥)中有机质生物可利用性的重要手段.分析了不同热水淬时间(1~24h)和不同ρ(污泥)(0.7~36.0g/L)对热水溶性蛋白质和碳水化合物等溶出的影响,据此对剩余污泥中热水溶性有机物的提取方法进行了优化. 结果表明:污泥在60℃水淬8h时,水溶性蛋白质和碳水化合物的溶出率达到最大,分别为34.6%和36.1%;但是,随着水淬时间的延长,部分蛋白质被转化成氨氮,部分碳水化合物也发生了转化和降解,致使二者的浓度降低. 考虑测试分析的时间效率和溶出率稳定性,污泥热水溶性有机物最优水淬时间建议设置为5h. 研究结果表明,热水溶性有机物的溶出率随ρ(污泥)降低呈升高趋势,当ρ(污泥)为0.7g/L时,热水淬5h后蛋白质和碳水化合物的溶出率最大,二者分别为52.9%和36.6%.      

典型电子废物中多溴联苯醚的模拟浸出释放特征

选取废旧打印机外壳为典型电子废物,以商用腐殖酸溶液为浸提剂,采用浸出试验,模拟研究了废旧打印机外壳中PBDEs(多溴联苯醚)在简易填埋或与生活垃圾共处置场景下,在不同废物粒径、浸提剂DOC浓度、pH、浸提时间和液固比下的浸出特征. 分别用索氏提取法和液液萃取法提取废旧打印机外壳及其浸出液中的PBDEs,采用气相色谱-质谱法(GC-MS)对11种PBDEs同系物的浓度进行定性、定量检测. 结果表明,废旧打印机外壳中BDE28、BDE47、BDE66、BDE85、BDE99、BDE100、BDE153、BDE154被检出,而在浸出液中仅有BDE28、BDE47、BDE66、BDE85、BDE99、BDE153被检出,∑₆PBDEs的浸出率仅为0.04%~0.44%;垃圾渗滤液和土壤溶液中DOM可以促进废旧打印机外壳中PBDEs的浸出,随着浸提剂ρ(DOC)的增大,PBDEs的浸出量增加;在酸性条件下PBDEs的浸出量低于在中性条件下的浸出量;随着浸出时间的延长,PBDEs的浸出量不断增加,但在试验设定的480h内,没有得到一个液固体系的平衡时间,可见废旧打印机外壳中PBDEs的浸出是一个缓慢释放的过程.      

超高效液相色谱-串联质谱法测定污水中14种有机磷酸酯阻燃剂

建立了超高效液相色谱-串联质谱(UPLC-MS/MS)联用法同时测定污水中14种有机磷酸酯阻燃剂(OPEs)的分析方法.样品采集后,经GF/C膜过滤,HLB固相萃取小柱净化后进样分析.以BEH C18色谱柱为分离柱,乙腈和水混合液为流动相(0.2 mL min-1)梯度洗脱,15 min内可完成14种OPEs的分离.在电喷雾正离子模式下,采用多反应监测模式(MRM)进行质谱测定.在加标浓度为1.0μg·L-1时,14种OPEs在污水处理厂进水和出水中的回收率分别为52.1%—119%、43.6%—114%,相对标准偏差(RSD)分别为1.2%—16.2%、0.4%—9.2%,方法的检出限(LOD)在0.3—6.0 ng·L-1间.方法精密度好,准确度高,可满足同时对污水样品中的14种OPEs进行定性及定量分析的要求.     

Indicating landfill stabilization state by using leachate property from Laogang Refuse Landfill

Variation and evolution process of leachate can be applied as a reference for landfill stabilization phase. In this work, leachates with different ages were collected from Laogang Refuse Landfill, and characterized with 14 key parameters. Simultaneously, principal component analysis （PCA） was applied to develop a synthetic parameter-F based on these 14 parameters, and a logarithm equation was simulated for the landfill stabilization process finally. It was predicted that leachates would meet Class I and Class II in standard for pollution control on the landfill site of municipal solid waste （GB 16889-1997） after 32 years and 22 years disposal under the natural attenuation in the humid and warm southern areas of China, respectively. The predication of landfill state would be more accurate and useful according to the synthetic parameter F of leachate from a working landfill.     

Comparative study on the efficiency and environmental impact of two methods of utilizing polyvinyl chloride waste based on life cycle assessments

Two processes of utilizing polyvinyl chloride （PVC） waste, an incineration process and a vacuum pyrolysis process, for energy conversion were compared to determine their efficiency and environmental perfor- mance. We carried out a life cycle assessment with each of the two processes to evaluate their environmental impact and defined the goals and limits of our remit. As well, we established an inventory of PVC waste from incineration and vacuum pyrolysis based on process analysis, data collection and calculations. The results show that electrical power output per unit mass of PVC waste in the incineration process was twice as high as that of the vacuum pyrolysis process. Incineration had a larger total environmental impact potential than vacuum pyrolysis. The total environmental impact potential of PVC waste from incineration was three times higher than that from vacuum pyrolysis. Incineration of PVC disposed 300 ng. 100 kgI of dioxins and vacuum pyrolysis 98.19 ng- 100 kgI of dioxins. As well, we analyzed the data for their uncertainty with results quantified in terms of three uncertainties： basic uncertainty, additional uncertainty, and computational uncertainty. The coefficients of variation of the data were less than 25% and the quality of the inventory data was acceptable with low uncertainty. Both PVC waste disposal processes were of similar quality and their results comparable. The results of our life cycle impact assessment （LCIA） showed considerable reliability of our methodology. Overall, the vacuum pyrolysis process has a number advantages and greater potential for development of PVC disposal than the incineration process.     

沸石滤池深度处理石化废水二级出水研究

采用小试规模沸石滤池,深度处理石化废水二级出水,通过考察滤池对CODCrNH4^-N和挥发酚的去除情况,分析了沸石去除污染物的规律和机理。结果表明：沸石滤池对CODCr,NH4^＋-N和挥发酚的平均去除率分别达到27．32％、94．67％和34．47％。在滤池运行初期,离子交换起主要作用。随着反应器的运行,离子交换因沸石饱和而减弱,而生物氧化逐渐起作用。由于沸石资源丰富、价格低廉和性能优越,所以沸石滤池作为三级深度处理技术具有广阔应用前景。     

污水处理厂低温等离子体恶臭治理技术

利用低温等离子体技术处理污水厂恶臭气体,是一种新的技术。介绍了该技术处理恶臭的机理和相关工程的工艺流程以及处理效果,实际应用表明该技术对污水处理厂恶臭气体的治理是十分有效的。     

对羧基苯偶氮硫代若丹宁固相萃取光度法测定环境样品中的铅

合成了新试剂对羧基苯偶氮硫代若丹宁(CPATR),并用红外光谱、核磁共振氢谱和元素分析鉴定其结构。研究了CPATR与铅的显色反应,在pH3 8的HAc—NaAc缓冲介质中,吐温-80存在下,CPATR与铅反应生成2∶1稳定络合物,该络合物可被WatersSep-PakC18小柱固相萃取,小柱上富集的络合物用乙醇洗脱后富集倍数可达50倍,在乙醇介质中,λmax=500nm,体系摩尔吸光系数ε=8.01×104L·mol-1·cm-1。铅含量在0 05～4 0mg/L内符合比耳定律。本方法可用于环境样品中铅含量的测定,结果满意。     

硫酸铝渣和硫铁矿烧渣制聚硅酸硫酸铁的研究

研究硫酸铝渣和硫铁矿烧渣制聚硅酸硫酸铁的工艺流程及其主要参数.提取硫酸铝渣中的SiO2得到Na2SiO3溶液,提取硫铁矿烧渣中铁得到FeSO4结晶.用FeSO4结晶制备聚合硫酸铁.用含3.5% SiO2的Na2SiO3溶液,控制pH=4.0,制得聚硅酸,将聚合硫酸铁加入聚硅酸制得聚硅酸硫酸铁絮凝剂.红外光谱分析表明,聚硅酸硫酸铁结合了SO2-4.检测了聚硅酸硫酸铁对模拟浊水和垃圾填埋场渗滤液的絮凝效果,用铁和硅物质的量比为0.5、用量0.5 mL/L的聚硅酸硫酸铁,处理模拟浊水,除浊率可达90%以上.用铁和硅物质的量比为1.5、用量4.0 mL/L的聚硅酸硫酸铁处理垃圾填埋场渗滤液生化处理尾水,CODCr去除率可达60%.     

小城镇固体废弃物处理调查研究

我国小城镇固体废弃物污染问题日趋严重,从小城镇实际情况出发,提出切实可行的固体废弃物处理办法和技术是当务之急.本文采用典型调查的方式,对我国7个典型小城镇进行实地调查,总结出了我国小城镇固体废弃物的特点,固体废弃物处理现状以及固体废弃物处理方面的规划,指出了我国小城镇在固体废弃物处理方面存在的问题,并就如何改善小城镇固体废弃物处理提出了建议.调查结果为小城镇固体废弃物的处理办法和技术研究提供了依据.