厌氧氨氧化电子受体的研究

在无机条件下,以该课题组已经培养出来的厌氧氨氧化污泥作为接种污泥,分别以硫酸盐、硝酸盐和亚硝酸盐为电子受体来研究氨的氧化反应。从去除速率的角度来看,以NO2--N、NO3--N和SO42--S为电子受体的反应器,分别在运行的第24.5天、40天和31天时达到0.030 0 kg/(m.3d)NH4+-N去除速率,则氧化氨的能力由大到小依次是:亚硝酸盐>硫酸盐>硝酸盐;从标准吉布斯自由能变化来看,3种反应都是可以发生的;以亚硝酸盐为电子受体的反应过程是一个消耗酸度的生物过程,而以硫酸盐为电子受体的反应过程是一个消耗碱度的生物过程。     

水解酸化-接触氧化法处理生活污水的工艺设计

厂区生活污水有机物及悬浮颗粒含量高,可生化性好。采用水解酸化-接触氧化法(厌氧/好氧)处理生活污水,目前系统运行稳定,出水各项指标达到国家GB 8978—1996《污水综合排放标准》中二级排放标准。设计处理能力为1 500 m3/d,处理后出水进入厂区回用水池。     

Photodegradation of amoxicillin by catalyzed Fe3+/H2O2 process

Three oxidation processes of UV-Fe³⁺(EDTA)/H₂O₂ (UV: ultraviolet light; EDTA: ethylenediaminetetraacetic acid), UV-Fe³⁺/H₂O₂ and Fe³⁺/H₂O₂ were simultaneously investigated for the degradation of amoxicillin at pH 7.0. The results indicated that, 100% amoxicillin degradation and 81.9% chemical oxygen demand (COD_Cr) removal could be achieved in the UV-Fe³⁺ (EDTA)/H₂O₂ process. The treatment efficiency of amoxicillin and COD_Cr removal were found to decrease to 59.0% and 43.0% in the UV-Fe³⁺/H₂O₂ process; 39.6% and 31.3% in the Fe³⁺/H₂O₂ process. Moreover, the results of biodegradability (biological oxygen demand (BOD₅)/COD_Cr ratio) revealed that the UV-Fe³⁺ (EDTA)/H₂O₂ process was a promising strategy to degrade amoxicillin as the biodegradability of the effluent was improved to 0.45, compared with the cases of UV-Fe³⁺/H₂O₂ (0.25) and Fe³⁺/H₂O₂ (0.10) processes. Therefore, it could be deduced that EDTA and UV light performed synergetic catalytic effect on the Fe³⁺/H₂O₂ process, enhancing the treatment efficiency. The degradation mechanisms were also investigated via UV-Vis spectra, and high performance liquid chromatography-mass spectra. The degradation pathway of amoxicillin was further proposed.     

活化过硫酸盐对市政污泥调理效果的影响

常规污泥脱水技术只能将市政污泥含水率降到80%左右,难以满足日益严格的污泥处理处置要求.活化过硫酸盐产生硫酸根自由基SO4·-具有强氧化性,可用于破坏污泥的絮体结构.本研究利用Fe2+活化过硫酸钠(SPS)的方法进行污泥调理,以到达改善污泥的脱水性能的目的.结果表明,当Fe2+与S2O2-8投加量(以绝干污泥计)分别为25.88 mg·g-1、80 mg·g-1(Fe2+与S2O2-8摩尔比为1.1∶1)时,污泥毛细吸水时间CST和污泥比阻SRF降低率最大,滤液中蛋白质和多糖浓度达到最大.进一步的研究表明,污泥Zeta电位值由负向正变化,颗粒比表面积增大,絮体由密集的团状变成结构松散的层状结构,污泥脱水性能提高.     

Fe-NaA分子筛膜的制备及催化湿式H2O2氧化甲基橙溶液

采用湿法造纸、二次生长和湿法浸渍法合成了一种新型微纤复合Fe-NaA分子筛膜催化剂,并将其用于催化湿式H_2O_2氧化甲基橙溶液.首先通过湿法造纸和烧结工艺制备纸状烧结不锈钢微纤(PSSF)载体,然后采用二次生长法在PSSF上合成NaA分子筛膜,最后以九水硝酸铁(Fe(NO_3)_3·9H_2O)和微纤复合NaA分子筛膜为原料,利用湿法浸渍法制备微纤复合Fe-NaA分子筛膜催化剂.考察了连续固定床反应器中温度、床层高度、进料液流量和甲基橙入口浓度对甲基橙降解性能的影响,并测定了催化剂重复使用3次后的稳定性.结果表明,随温度及床层高度增加,甲基橙转化率先增加然后趋于稳定;随进料液流量增加,甲基橙转化率均大于95%,但COD脱除率略有降低,当流量分别为2、3和4 mL·min~(-1),固定床连续运转5 h时COD脱除率分别为81.9%、76.4%和69.8%;随甲基橙入口浓度增加,其转化率变化幅度很小.在pH=2、催化剂床层高度2.0 cm、温度70℃、进料液流量4 mL·min~(-1)、甲基橙浓度50～200 mg·L~(-1)、固定床连续运转5 h的条件下,甲基橙转化率超过96%,COD转化率大于67%,铁浸出浓度低于4 mg·L~(-1).催化剂被重复使用3次后,甲基橙转化率基本保持不变.     

钛基改性DSA电极氧化法去除水中全氟化合物

为了提高金属氧化物电极(DSA电极)的稳定性及催化活性,实现全氟化合物(PFCs)的高效降解,分别以溶胶涂覆法和电沉积法制备了改性DSA(Ti/SnO_2-ZnO)电极,并用于全氟辛酸(PFOA)和全氟辛烷磺酸(PFOS)的电化学降解过程研究.实验分别考察了电流密度、溶液初始pH、 PFOA与PFOS初始浓度对PFCs降解效果的影响.结果表明:两种方法制备的改性DSA电极表面均匀负载了SnO_2-ZnO复合涂层.在二维电极体系中,极板面积约为65.0 cm~2,电流密度为20.0 mA·cm~(-2),极板间距为15.0 mm,电解质为1.30 g·L~(-1)次氯酸钠溶液以及电解时间为150 min时,溶胶涂覆法和电沉积法所制备的Ti/SnO_2-ZnO电极对初始浓度为100 mg·L~(-1)的PFOA和PFOS分别在pH为3.50和6.50时去除效果最佳,分别达到了90.6%、94.6%和91.0%、93.7%;循环使用电极3次,其降解过程均符合准一级反应动力学,且电沉积法制备的电极效果优于溶胶涂敷法,表现出对PFCs类污染物稳定、高效的去除能力.     

铜前驱体对Cu/SSZ-13催化剂选择性催化氧化NH3性能的影响

采用浸渍法制备了一系列Cu/SSZ-13(X)催化剂,考察不同铜前驱体对催化剂选择性催化氧化氨(NH_3-SCO)性能的影响,并通过ICP、N_2吸附-脱附、XRD、XPS、EPR、UV-Vis、NH_3-TPD和H_2-TPR等手段对催化剂进行物化性质表征.活性测试结果表明,不同铜前驱体制备的Cu/SSZ-13催化剂活性顺序为Cu/SSZ-13(N) Cu/SSZ-13(AC) Cu/SSZ-13(Cl) Cu/SSZ-13(O).其中Cu/SSZ-13(N)具有最佳的低温活性,在200℃反应温度下NH_3转化率达85.5%,且N_2选择性达到80%以上.XRD、EPR和UV-Vis分析表明,CuO和孤立Cu~(2+)是Cu/SSZ-13催化剂的主要铜物种.NH_3-TPD分析表明,以硝酸铜为前驱体制备的Cu/SSZ-13(N)具有更多的酸性位点,有利于提高催化剂的NH_3吸附能力.H_2-TPR结果表明,Cu/SSZ-13(N)的氧化还原性最强,具有最优异的NH_3活化能力,从而使催化剂呈现最好的低温NH_3-SCO活性.     

基于好氧甲烷氧化菌的反硝化效能及微生物群落研究

采用气体循环序批式生物膜反应器（gcSBBR）,构建反硝化型甲烷好氧氧化（AME-D）系统.考察了进水氮负荷的影响,发现氮负荷为0.075kg/（m³·d）时,硝酸盐氮去除率达到98.93%,其反硝化速率为74.25mg/（L·d）,系统的甲烷日平均消耗量为35.91%（初期为50%）;扫描电子显微镜（SEM）分析结果显示,系统中的微生物主要以短杆菌（12~18 μm）为主,并存在少量的丝状菌（长150~200μm）;16S rRNA高通量测序结果显示,该系统中的甲烷氧化菌为Methylocaldum、Methylomonas、Methylococcus和Methylococcaceae_unclassified,反硝化菌为Denitratisoma、Hydrogenophaga、Azoarcus、Thiobacillus和Rhodobacter,其中主要的功能微生物为Methylocaldum、Denitratisoma和Hydrogenophaga,系统对氮的去除是由好氧甲烷氧化菌与反硝化菌协同实现.此外,系统中存在大量以甲醇和甲基胺类物质为生长基质的Methylophilaceae_uncultured（30.4%）.     

Pilot-scale experiments on multilevel contact oxidation treatment of poultry farm wastewater using saran lock carriers under different operation model

A pilot-scale multilevel contact oxidation reactors system, coupled with saran lock carriers,was applied for the treatment of poultry farm wastewater. The removal efficiencies of CODcr, ammonia, and the total nitrogen as well as the elimination performance of CODcr and total nitrogen along the three-level contact oxidation tanks under six designed operational models were investigated. Based on the performance of the nitrogen removal of the saran lock carriers and the distribution of anoxic–aerobic interspace under the suitable operation model, the mechanism of nitrogen removal of the system was also explored. The results revealed that the intermittent aeration under parallel model is the most suitable operation model, while the removal efficiencies of CODcr, ammonia, and the total nitrogen were 86.86%, 84.04%, and 80.96%, respectively. The effluent concentration of CODcr,ammonia, and the total nitrogen were 55.6 mg/L, 8.3 mg/L, and 12.0 mg/L, which satisfy both the discharge standard of pollutants for livestock and poultry breeding industry(GB18596–2001) and the first grade of the integrated wastewater discharge standard(GB 8978–1996). Moreover, the mechanism for the nitrogen removal should be attributed to the plenty of anoxic–aerobic interspaces of the biofilm and the three-dimensional spiral structure of the saran lock carriers, where the oxygen-deficient distribution was suitable for the happening of the simultaneous nitrification and denitrification process. Therefore, the multilevel contact oxidation tanks system is an effective pathway for the treatment of the poultry farm wastewater on the strength of a suitable operation model and novel carriers.     

安徽铜陵铜尾矿硫形态及硫同位素分布特征

分析讨论了安徽铜陵水木冲S和SP剖面尾矿砂的理化指标、硫形态变化和硫酸根硫同位素组成与分布特征.结果显示：S和SP剖面整体呈酸性,pH值为2.59~6.12和3.50~6.27,由下而上有明显的降低趋势;Eh随剖面由下至上明显升高,范围为66~457和-37~307mV;酸可挥发性硫（AVS）含量为0~62.36和0~3.44mg/g,黄铁矿硫（CRS）含量为0.70~32.30mg/g和0.17~5.39mg/g;AVS与CRS的变化趋势基本一致,随剖面自下而上减少,且AVS先于CRS被氧化.2个剖面元素硫（ES）含量为0~8.83和0~3.62mg/g,随深度变化无明显规律.硫酸根硫（SO₄^2--S）含量为8.44~66.34和8.48~29.87mg/g,自下而上呈降低趋势,且分别在剖面的氢氧化物薄膜层（11.5~16.5cm和18~54cm）出现高值区.2个剖面总硫（TS）含量为9.18~109.69和12.38~37.72mg/g,表层由于淋滤含量较低,底层变化则不大.位于斜坡上的SP剖面TS及各形态硫含量均低于S剖面,表明淋滤对硫含量影响更明显.硫酸根硫同位素δ³⁴S为-3.32‰~13.43‰和-3.08‰~1.80‰,S-9硫酸根δ³⁴S为13.43‰,指示其来自于伴生硬石膏,其余层位δ³⁴S偏负且变幅较小,指示其硫酸根主要来源于硫化物的氧化.