模糊综合评价法在钢铁企业安全投资合理性评价中的应用

为了对钢铁企业安全投资进行模糊综合评价,建立了钢铁企业安全投资的评价体系,确定各因素的权重。得出模糊综合评价矩阵,可对各因素进行评价分析;得出某钢铁企业安全投资现状分数为83.9分,等级为较好,需着重加强安全培训、劳保品、工业卫生等人因素方面的投资;在环境方面的投资较合理。     

青岛海洋环境碳纤维复合材料与低合金钢电偶腐蚀研究

目的 探究碳纤维复合材料在舰船应用时与金属材料的电偶腐蚀问题。方法 针对一种典型舰船用碳纤维增强乙烯基树脂复合材料,在青岛海洋大气环境下开展0.5、1、1.5、2 a期的自然曝晒试验,进而采用电化学分析手段考察其与低合金钢的电偶腐蚀效应,结合老化机制探究碳纤维复合材料的老化行为对其与钢电偶腐蚀的影响。结果及结论 在青岛大气环境曝晒不同周期的复合材料试样,开路电位与低合金钢相差较大,存在较高的电偶腐蚀倾向。随曝晒时间的延长,复合材料表面微裂纹不断产生、扩展,导致电化学反应活性点增多,两者电偶电流密度随之增大。在青岛海洋大气环境下暴露2 a后,碳纤维增强乙烯基树脂复合材料与低合金钢的电偶电流为0.356 9 μA/cm²,两者的电偶腐蚀敏感性达到B级。     

不同构造措施的钢管混凝土边框钢板剪力墙抗震性能试验研究

钢管混凝土边框钢板剪力墙是一种新型抗震剪力墙,为了比较不同构造措施对该新型剪力墙抗震性能的影响,进行了3个剪跨比为1.5的钢管混凝土边框钢板剪力墙低周反复荷载试验.其中,试验模型1为墙体钢板与边框柱钢管焊接,试验模型2为墙体钢板与边框柱钢管螺栓连接,试验模型3为墙体钢板开孔并与边框柱钢管焊接.通过试验研究,比较了各剪力...     

钢渣吸附-微波降解法处理碱性品红废水

研究了钢渣对碱性品红染料的吸附性能、影响因素以及微波对吸附在钢渣-焦炭上的染料的降解作用。实验表明,在中性条件下,钢渣对碱性品红具有优良的吸附性能,饱和吸附量可达到42．4mg／g。以钢渣处理质量浓度为100mg/L的碱性品红溶液,当固液质量比为1：50、振荡吸附1h后,染料溶液脱色率达97％。实验还表明,焦炭可吸收微波产生高温,用钢渣-焦炭混合物（质量比1：1）吸附染料后,以微波辐照可使物料达到665℃的高温,吸附的染料降解。吸附剂再生后重复使用4次,脱色率都达到95％以上。     

钢渣预处理含铬废水及其废渣与铬渣的固化

用钢渣对含铬废水进行预处理,探讨了钢渣粒度、用量、废水pH值和添加硫酸亚铁还原剂的影响.结果表明,经硫酸亚铁还原处理后再用钢渣处理比单纯用钢渣处理的效果明显提高,采用钢渣/总铬质量比为40的100目钢渣处理经硫酸亚铁还原后的含铬废水,总铬和Cr6 去除率分别达79%和84%,采用钢渣柱进行的两级淋滤实验进一步表明该方法可作为工业上含铬废水处理的预处理段.处理后的废钢渣同工业铬渣一起进行水泥固化,标准养护20 d后固化体表面Cr6 浸出率、破碎至5 mm粒径以下和酸雨淋溶下的浸出液Cr6 浓度均符合安全标准,可作为普通建材或进行填埋处置.     

CDM Project Activities in China＇s Iron and Steel Industry：Current Status,Barriers and Development Strategies

China is now facing huge pressure from both the domestic concern of energy security and the global community's call for emission reduction commitment. As one of the major energy consumers and greenhouse gas emitters, China's iron and steel industry has a huge clean development mechanism (CDM) potential. This article both quantitatively and qualitatively analyzes the current status of CDM project activities in the iron and steel industry in China, including characteristics of approved project types, applicable methodologies, and potential technology fields. From the perspective of project implementation, the article summarizes development barriers such as high investment risk, difficulty in project identification, strict requirements on PPDs, long registration waiting time, and etc. Policy suggestions are also put forwarded to help better promote the development of CDM projects in the iron and steel industry.     

废钢铁切割加工烟尘的治理

介绍了氧-乙炔火焰切割加工废钢铁产生的烟尘治理系统的设计和系统设备选型,重点介绍了烟尘捕集罩的设计和除尘器、电磁脉冲阀、风机的选型和PLC自动控制以及系统实际运行效果,为废钢铁加工企业治理污染提供一套简单、经济、实用的除尘系统作参考.     

Technologically enhanced 210Pb and 210Po in iron and steel industry

Iron and steel manufacture has been ranked as the largest industrial source of environmental contamination in the USA; the wastes generated in their production processes contain heavy elements that can be a source of contamination, and natural radionuclides that can produce an occupational and/or public radiological impact. In this work the potential occupational effective dose rate (μSv/y) due to inhalation in four integrated steel-making factories from Egypt has been evaluated, by assuming a well defined scenario and with basis in the ²¹⁰Pb and ²¹⁰Po activity concentrations determined in ore and wastes collected in the aforementioned factories. Activity concentrations, in Bq/kg, of ²¹⁰Pb and ²¹⁰Po, and leachable Pb and Fe were measured using gamma-ray spectrometry based on HPGe detector, alpha particle spectrometry based on PIPS detector, and inductively coupled plasma-mass spectrometry (ICP-MS). Levels of ²¹⁰Pb and ²¹⁰Po in the range of <DL-4238 and 1-5660 Bq/kg, respectively, were found. According to the assumed scenarios, the occupational exposures by inhalation are much lower than the recommended annual effective dose limit, although the environmental impact due to waste storage and/or use should be considered based on case by case evaluation.     

加氢裂化REAC系统双相不锈钢管道焊缝铁素体含量的讨论

本文介绍了专利商对应用于加氢裂化REAC系统的双相不锈钢S32205焊接接头的要求,简要说明了双相不锈钢的焊接工艺评定;分析了填充金属化学成分、焊接线能量、焊接冷却速度对双相不锈钢焊缝铁素体含量的影响;分析了双相不锈钢焊缝铁素体含量达到专利商要求的能力,以及手工电弧焊焊缝铁素体含量达不到专利商35%~60%要求的原因是焊条化学成分设计的结果;分析了焊缝铁素体含量要求的合理性,介绍了AWS、API、NACE及国家行业标准对于双相不锈钢焊接接头铁素体含量的要求;介绍了现场的焊接工艺,以及使实际焊缝达到使用要求的方法.     

Advantages and risks of using steel slag in preparing composts from raw organic waste

It had been reported that iron and manganese oxides in steel slag enhanced the production of humic acid (HA) from low-molecular-weight compounds, such as phenolic acids, amino acids, and saccharides. In the present study, this function of steel slag was applied to the composting of raw organic wastes (ROWs). The degree of humification of HAs is an important factor in evaluating compost quality. Thus, HAs were extracted from the prepared composts and the humification parameters were determined, in terms of elemental compositions, acidic functional group contents, molecular weights, spectroscopic parameters from UV–vis absorption and ¹³C NMR spectra. The timing for adding steel slag affected the degree of humification of HAs in the composts. The weight average molecular weight of a HA when slag was added initially (29 kDa) was significantly higher than when slag was added after elevating the temperature of the compost pile (17–18 kDa). These results show that ROWs are decomposed to low-molecular-weight compounds after the pile temperature is elevated and the presence of slag enhances the polycondensation of these compounds to produce HAs with a higher degree of humification. Because the slag used in the present study contained several-tens ng g^?1 to several μg g^?1 of toxic elements (B, Cu, Cr, and Zn), leaching tests for these elements from the prepared composts were carried out. Levels for leaching boron from composts prepared by adding slag (0.2–0.4 mg L^?1) were obviously higher than the corresponding levels without slag (0.05 mg L^?1).