装修用板材的导热性能分析

导热系数是物体的重要物理指标,对四种板材的导热系数进行了测试,并对导热性能进行了分析。     

GB/T 7702-2008《煤质颗粒活性炭试验方法》标准的研究

通过对GB/T 7702-2008《煤质颗粒活性炭试验方法》的修订,研究了国际上先进国家的ASTM、JIS、ГОСТ同类标准内容。本系列标准除等同采用部分国际先进标准外,还结合本国特点增加了部分国外标准没有的内容,同时着重对碘吸附值测定进行了深入研究,确定了国际先进的碘吸附值试验方法。     

呼吸器标准中的泄漏率与实验室呼吸防护水平

结合国内外呼吸器最新标准中有关泄漏率与实验室呼吸防护水平的测试条件和方法,从基本概念和评价方法入手对比剖析了不同标准之间内容的差异.文中涉及的国内外标准主要有美国职业安全与健康研究所指定的系列化生放核呼吸器标准、欧洲EN 13274 - 1:2001、日本JIST8159:2006、中国GB 2626 - 2006和GB 2890 - 2009以及ISO/DIN 16900-1.2草案.通过对比分析不同标准之间在评价方法中采用的气溶胶种类、受试者人数、模拟动作种类及持续时间、采样方法、测试结果评价方法等具体内容,指出了我国呼吸器标准中泄漏率测试方法及相关标准发展中应注意的问题.     

用有限元强度折减法求解坝坡抗滑稳定安全系数

通过对有限元强度折减法的理论研究,将此法应用到尾矿坝的静力稳定计算中.采用有限元强度折减法和极限平衡法对某尾矿坝进行了坝坡抗滑稳定安全系数的计算,计算结果表明,在应用有限元强度折减法时,采用不同的D-P准则计算出的滑动面基本相同且与传统方法相近,其中D-P3准则计算的安全系数更加接近瑞典圆弧法.因此应用有限元强度折减法求解尾矿坝静力稳定安全系数是可行的,同时说明有限元法可以较好的模拟实际工程中的复杂几何断面形状和材料非线性等问题.     

絮凝剂用壳聚糖的中试生产研究

在实验室制备絮凝剂用壳聚糖的基础上,按工业化生产的要求对壳聚糖进行了中试生产研究.经正交试验确定了生产过程中脱钙、脱蛋白、脱乙酰等3步反应的最佳工艺参数. 由此中试工艺生产的壳聚糖的生产成本比国内同类产品下降了22%,生产周期缩短了66%,且主要性能指标均达到或超过国内外同类产品的水平.     

Laboratory investigation of Waelz slag stabilization

Electric Arc Furnace dusts are considered hazardous waste due to their high heavy metals content (zinc, lead, etc.). The Waelz process is one of the most efficient technologies, in terms of capacity and quality, able to recover nearly the 90% of zinc contained in such EAF dusts. Unfortunately, the resulting slag still has eco-compatibility problems, although its mechanical and chemical properties are suitable for civil engineering applications. Stabilization tests, by quartz addition, were performed on EAF dusts in a laboratory furnace. Temperature, treatment time and cooling rate were varied in order to define the best conditions for regulating the formation of a stable microstructure able to hinder the release of substances. Microstructural characterization was carried-out using SEM and XRD analysis. Leaching tests were performed according to EN 12457-2 standards and water analyses were performed using ICP-OES. The best chemical stability was achieved when dust powders were mixed with 20% of silica and water-cooled.     

THOR dummy chest deflection response in oblique and lateral far-side sled tests

Abstract

Objective: The focus of this study is side impact. Though occupant injury assessment and protection in nearside impacts has received considerable attention and safety standards have been promulgated, field studies show that a majority of far-side occupant injuries are focused on the head and thorax. The 50th percentile male Test Device for Human Occupant Restraint (THOR) has been used in oblique and lateral far-side impact sled tests, and regional body accelerations and forces and moments recorded by load cells have been previously reported. The aim of this study is to evaluate the chestband-based deflection responses from these tests.

Methods: The 3-point belt–restrained 50th percentile male THOR dummy was seated upright in a buck consisting of a rigid flat seat, simulated center console, dashboard, far-side side door structure, and armrest. It was designed to conduct pure lateral and oblique impacts. The center console, dashboard, simulated door structure, and armrest were covered with energy-absorbing materials. A center-mounted airbag was mounted to the right side of the seat. Two 59-gage chestbands were routed on the circumference of the thorax, with the upper and lower chestbands at the level of the third and sixth ribs, respectively, following the rib geometry. Oblique and pure lateral far-side impact tests with and without airbags were conducted at 8.3 m/s. Maximum chest deflections were computed by processing temporal contours using custom software and 3 methods: Procedures paralleling human cadaver studies, using the actual anchor point location and actual alignment of the InfraRed Telescoping Rods for the Assessment of Chest Compression (IR-TRACC) in the dummy on each aspect—that is, right or left,—and using the same anchor location of the internal sensor but determining the location of the peak chest deflection on the contour confined to the aspect of the sensor; these were termed the SD, ID, and TD metrics, respectively.

Results: All deformation contours at the upper and lower thorax levels and associated peak deflections are given for all tests. Briefly, the ID metrics were the lowest in magnitude for both pure lateral and oblique modes, regardless of the presence or absence of an airbag. This was followed by the TD metric, and the SD metric produced the greatest deflections.

Conclusion: The chestbands provide a unique opportunity to compute peak deflections that parallel current IR-TRACC-type deflections and allow computation of peak deflections independent of the initial point of attachment to the rib. The differing locations of the peak deflection vectors along the rib contours for different test conditions suggest that a priori attachment is less effective. Further, varying magnitudes of the differences between ID and TD metrics underscore the difficulty in extrapolating ID outputs under different conditions: Pure lateral versus oblique, airbag presence, and thoracic levels. Deflection measurements should, therefore, not be limited to an instrument that can only track from a fixed point. For improved predictions, these results suggest the need to investigate alternative techniques, such as optical methods to improve chest deflection measurements for far-side occupant injury assessment and mitigation.     

不同警告方式下驾驶人应激反应能力模拟试验研究

为研究在道路突发危险场景下先进驾驶辅助系统的不同警告方式对驾驶人应激反应能力的影响，利用自主开发的驾驶人应激反应能力测试软件，以计算机模拟与驾驶模拟器为试验平台，以实际驾驶视频为试验场景，选取操作准确率和反应时间为测试指标，分析不同警告方式下驾驶人的应激反应能力。研究结果表明:视觉警告可有效缩短应激反应时间；视听觉组合警告中，视觉警告占主导作用，听觉警告起辅助作用；在真实场景视频试验环境下，驾驶模拟器模拟试验的操作效果优于计算机模拟试验。     

可燃制冷剂空调用开关元件点燃危险及防爆试验分析

随着全球范围对环境问题的日益重视,R290,R32等新型制冷剂因优良的环保性能和节能效果被广泛应用于空调行业,但其属于IIA级爆炸性气体,为了进一步分析其运行过程中的防爆安全性能。通过文献数据和测试分析,可燃制冷剂空调电气元件的点燃源主要来自其工作过程中产生的电气火花。其中空调开关元件最容易产生电火花、电弧,且通过试验验证这些火花或电弧能点爆（6.5±0.5）%乙烯/空气混合物。综合IEC 60335-2-40,GB 4706.32标准要求和空调开关元件的结构特征,分析确定其应符合“nC”型防爆技术要求,并能通过“nC”型爆炸试验。针对开关元件结构尺寸小、存在爆炸试验中爆炸性混合气体多次置换和负载通、断电操作的难点问题,提出一套合理可行的爆炸试验实施方案,并通过测试应用得到验证。     

顶板含水层防水试验的钻孔单位涌水量计算方法

为了实现利用井下放水试验获取顶板含水层的钻孔单位涌水量,采用抽水试验中的地下水动力学计算公式,结合观测孔的水位降深,给出了放水孔水位降深的计算方法;利用观测孔水位降深和观测孔与放水孔之间距离的对数曲线图,提出了放水孔水位降深的图解法;对于承压含水层,基于钻孔单位涌水量与含水层渗透系数之间的线性相关关系,可以通过含水层的渗透系数获取钻孔单位涌水量;通过实例分析,解析法和图解法计算得到的放水孔单位涌水量相近,结合现场放水试验情况,分析了放水孔单位涌水量的可靠性,并对3种方法的适用条件进行了讨论。研究结果表明:利用放水试验获取的放水孔单位涌水量符合实际情况,可以作为含水层富水性评价和矿井水文地质条件分析的依据。