构树修复对重金属污染土壤环境质量的影响

通过温室盆栽试验,研究构树（Broussonetia papyrifera）生长对重金属污染土壤酶活性和微生物群落结构的影响.结果表明,构树修复污染土壤中酶活性和微生物多样性明显提高.经270d培养后,构树生长土壤中蔗糖酶和酸性磷酸酶活性与种植土壤相比分别显著（P<0.05）提高3.12倍和2.29倍;土壤脱氢酶与有效态As、Cd、Pb、Zn和Cu含量,蔗糖酶与有效态Cd含量,以及磷酸酶与有效态Cd和Cu含量之间呈显著负相关（P<0.05）.根据16S和18S rDNA PCR-DGGE分析表明,构树修复可提高污染土壤中细菌和丛枝菌根真菌多样性.上述结果表明,构树修复可有效改善重金属污染土壤的环境质量.然而,污染土壤中重金属有效态含量下降不明显,必须辅助物理和化学措施来强化构树对重金属污染土壤的生态修复潜力.     

考虑边界条件不确定性的地下水污染风险分析

为分析边界条件不确定性对地下水污染质运移数值模拟模型输出结果的影响,运用Monte Carlo方法对一算例进行阐明,并从污染风险预报方面对模拟结果进行分析.为减少重复调用模拟模型产生的大量计算负荷,将边界条件（第一类边界条件-水头值）作为随机变量,建立地下水污染质运移数值模拟模型的Kriging替代模型,在保证较高精度的同时,实现了Monte Carlo模拟.结果表明：边界条件的不确定性,对地下水污染质运移数值模拟模型预报的结果有很大影响,考虑与未考虑边界条件不确定性得到的研究区污染羽分布差别较大.对地下水污染质运移数值模拟模型的Monte Carlo模拟结果进行统计与分析,可以评估研究区观测井1,2,3污染物浓度预报结果的可靠程度,并且可以预报出研究区观测井1,2,3遭受不同程度污染的风险.     

应用S-T模型对沉积物中PAHs的生态风险分级评价

本文构建S-T模型,运用集对分析理论（set pair analysis）构建基本模型,采用层次分析法并参考毒性当量因子确定各指标权重,应用三角模糊数（triangular fuzzy number）对差异度系数进行改进,基于加拿大沉积物环境质量标准,对沉积物中多环芳烃进行生态风险分级评价.结果表明,该模型考虑到化合物之间的相互作用因素并做模糊处理,对差异度系数进行改进体现沉积物中多环芳烃生态风险等级标准的模糊性,为持久性有机污染物生态风险分级评价提供了一种简便客观有效的方法.     

Nanoencapsulation of hexavalent chromium with nanoscale zero-valent iron: High resolution chemical mapping of the passivation layer

Solid phase reactions of Cr(Ⅵ) with Fe(0) were investigated with spherical-aberration-corrected scanning transmission electron microscopy(Cs-STEM) integrated with X-ray energy-dispersive spectroscopy(XEDS). Near-atomic resolution elemental mappings of Cr(Ⅵ)–Fe(0) reactions were acquired. Experimental results show that rate and extent of Cr(Ⅵ) encapsulation are strongly dependent on the initial concentration of Cr(Ⅵ) in solution. Low Cr loading in nZⅥ(1.0 wt%) promotes the electrochemical oxidation and continuous corrosion of n ZⅥ while high Cr loading(1.0 wt%) can quickly shut down the Cr uptake. With the progress of iron oxidation and dissolution, elements of Cr and O counter-diffuse into the nanoparticles and accumulate in the core region at low levels of Cr(Ⅵ)(e.g., 10 mg/L). Whereas the reacted n ZⅥ is quickly coated with a newly-formed layer of 2–4 nm in the presence of concentrated Cr(Ⅵ)(e.g., 100 mg/L). The passivation structure is stable over a wide range of pH unless pH is low enough to dissolve the passivation layer. X-ray photoelectron spectroscopy(XPS) depth profiling reconfirms that the composition of the newly-formed surface layer consists of Fe(Ⅲ)–Cr(Ⅲ)(oxy)hydroxides with Cr(Ⅵ) adsorbed on the outside surface. The insoluble and insulating Fe(Ⅲ)–Cr(Ⅲ)(oxy)hydroxide layer can completely cover the n ZⅥ surface above the critical Cr loading and shield the electron transfer. Thus, the fast passivation of nZⅥ in high Cr(Ⅵ) solution is detrimental to the performance of nZⅥ for Cr(Ⅵ) treatment and remediation.     

Mercury flows in large-scale gold production and implications for Hg pollution control

Large-scale gold production(LSGP) is one of the five convention-related atmospheric mercury(Hg) emission sources in the Minamata Convention on Mercury. However, field experiments on Hg flows of the whole process of LSGP are limited. To identify the atmospheric Hg emission points and understand Hg emission characteristics of LSGP, Hg flows in two gold smelters were studied. Overall atmospheric Hg emissions accounted for 10%–17% of total Hg outputs and the Hg emission factors for all processes were 7.6–9.6 kg/ton. There were three dominant atmospheric Hg emission points in the studied gold smelters, including the exhaust gas of the roasting process, exhaust gas from the environmental fog collection stack and exhaust gas from the converter of the refining process. Atmospheric Hg emissions from the roasting process only accounted for 16%–29% of total emissions and the rest were emitted from the refining process. The overall Hg speciation profile(gaseous elemental Hg/gaseous oxidized Hg/particulate-bound Hg) for LSGP was 34.1/57.1/8.8. The dominant Hg output byproducts included waste acid, sulfuric acid and cyanide leaching residue. Total Hg outputs from these three byproducts were 80% in smelter A and 84% in smelter B. Our study indicated that previous atmospheric Hg emissions from large-scale gold production might have been overestimated.Hg emission control in LSGP is not especially urgent in China compared to other significant emission sources(e.g., cement plants). Instead, LSGP is a potential Hg release source due to the high Hg output proportions to acid and sludge.     

Relationship between PM10 and PM2.5 levels in high-traffic area determined using path analysis and linear regression

The objective of this study was to determine the relationship between PM_(10) and PM_(2.5) levels as related to meteorological conditions and traffic flow using both a linear regression analysis and a path analysis. The Particulate matter(PM) samples were collected from Sukhumvit road, Bangkok, Thailand, at both open(104 samples) and covered(92 samples)areas along the road. Fifteen percent of all samples were separated before the statistical models were run and used for model validation. The results from the path analysis were more elaborate than those from the linear regression, thus indicating that meteorological conditions had a direct effect on the particulate levels and that the effects of traffic flow were more variable in open areas. The model also indicated that meteorological conditions had an indirect effect and that traffic flow had a direct effect on particulate levels in covered areas. The model validation results indicated that for open areas, the R~2 values were not very different between the path analysis and the linear regression model, but that the path analysis was more accurate than the linear regression model at very low PM concentrations. At high PM concentrations, the path analysis model also had a better fit than did the linear regression, so the predictions from the path analysis model were more accurate than those from the linear regression.     

铜合金实验室试验与实海挂片结果的比较与分析

目的比较实验室试验结果与实海挂片结果对B10和H62两种铜合金腐蚀性能评价的异同之处。方法采用线性极化、电化学阻抗、显微形貌观察等,比较两种铜合金在实验室模拟海水中的的腐蚀速率、点蚀倾向,结合反应机理、腐蚀形貌、环境等外部因素,分析导致实验室与实海环境下出现差异的原因。结果除榆林海域外,实海挂片与实验室结果都表明,B10试样的平均腐蚀速率小于H62。B10和H62两种铜合金随温度升高腐蚀速率增大,在实验室和实海情况下表现出一致性,且平均腐蚀速率都随浸泡时间的延长而降低。结论在实海环境中,温度不是影响点蚀的主要因素,微生物等其他环境因素会对点蚀产生较大影响。     

可靠性强化试验技术在某型伺服作动器研制中的适用性探索

目的探索可靠性强化试验技术在典型机电液一体化产品伺服作动器研制过程中的适用性。方法以某型伺服作动器为研究对象,从故障激发的角度对可靠性强化试验技术的应用进行可行性分析,在响应调查和应力分析的基础上,结合产品的工作特点设计适用于该类伺服作动器的可靠性强化试验方案,包含低温步进应力试验、高温步进应力试验、快速温度循环试验10个循环、振动步进应力试验(包含气锤式三轴向六自由度超高斯随机振动方式及电磁振动台随机振动方式)及综合环境应力试验5个循环,并依此进行试验。结果在快速温度循环试验及综合环境应力试验过程中,均有效地激发出了产品的漏油故障,与相似产品外场暴露的漏油故障模式相吻合。结论可靠性强化试验技术可有效地应用于典型机电液一体化产品伺服作动器的研制过程,设计的可靠性强化试验方案可有效地激发外场出现频率较高的故障,可作为该类产品研制的试验手段之一。     

“天舟一号”货运飞船在轨污染探测数据分析

目的分析"天舟一号"(TZ-1)货运飞船的空间污染探测器的在轨探测数据。方法 TZ-1货运飞船上的污染探测器采用石英晶体微量天平(QCM),利用污染物沉积在QCM探测器传感晶片表面引起的振荡频率变化情况来分析航天器在轨空间污染环境。根据其探测原理,通过分析下传的原始数据,得到航天器在轨的污染累积量结果。结果航天器在轨飞行过程中,污染累积已达到会导致污染敏感器件光学性能明显退化的程度,并且污染源温度是影响航天器污染累积量的一个重要因素,可以将其作为航天器在轨污染控制的重要措施。结论该研究结果可以为航天器污染设计、控制提供参考,为提高航天器可靠性设计提供数据支持。     

某型飞机外翼5—8肋损伤原因分析及修复探讨

目的 分析某型飞机外翼5—8肋油箱区结构不同程度损伤的原因,制定修复方案。方法采用受载分析、有限元仿真计算、静力试验数据分析等强度计算方法分析损伤产生的原因,采用扫描电子显微镜和光学显微镜对磨痕形貌进行观测等失效分析,对损伤结构件开展失效模式分析,根据损伤原因及失效模式制定科学简便的修复方案,同时对损伤长桁采取的修补措施进行强度校核。结果 通过对外翼油箱充压破坏理论分析、有限元仿真计算、静力试验数据反推,并结合飞机实际损伤情况,得出油箱破坏理论分析危险薄弱部位与真实破坏情况一致的结论。有限元仿真计算最危险结构部位与实际结构首先发生破坏部位吻合,可作为深入制定修复方案及推测实际加载压力的依据。通过静力试验数据反推、结构实际损伤及有限元仿真计算结论得出,外翼5—8肋结构出现损伤时油箱施加压力约0.5 MPa,针对损伤制定了更换外翼油箱内部第5—8肋损伤结构和贴补加强损伤长桁的修理方案,经结构强度校核,满足设计要求。结论 分析认为外翼5—8肋油箱区结构损伤原因为油箱压力超过设计值导致结构过载断裂,采用贴补加强修理损伤长桁和更换第5—8肋损伤结构的修复方案能够满足强度设计要求,可指导同类飞机类似结构损伤故障的原因分析和修理,提醒同类飞机维修人员在飞机维护时应关注外翼油箱压力超压问题。