废聚苯乙烯泡沫塑料的催化裂解

为了对废聚苯乙烯泡沫塑料（WPS）资源化利用,通过对WPS进行催化裂解的方法,研究了催化剂种类和裂解温度对裂解时间、裂解油产率、苯乙烯回收率以及裂解油纯度的影响。研究结果表明,催化剂种类和裂解温度对裂解反应有着重要影响。裂解温度升高,裂解油产率提高,裂解时间缩短,但苯乙烯选择性下降;低于380 ℃时,氧化钙的裂解油产率和裂解时间优于氧化铝和氯化铝,但苯乙烯的选择性劣于氧化铝和氯化铝;高于400 ℃时,氯化铝、氧化铝和氧化钙的催化活性接近。在实验条件下,WPS催化裂解的最佳催化剂为氯化铝,380 ℃下的裂解时间为25 min,裂解油产率为85.48%,裂解油中苯乙烯含量为80.66%（w）,且副产物较少。     

硝基苯甲酸结构对其在EPDM膜中萃取效果的影响

以3种取代基位置不同的硝基苯甲酸为研究对象,研究了辛醇/水分配系数、溶解度、摩尔体积、分子极化率和偶极矩5种结构参数对硝基苯甲酸在三元乙丙橡胶（EPDM）膜中萃取效果的影响。实验结果表明：EPDM膜对硝基苯甲酸有一定的去除效果,邻、间、对硝基苯甲酸的去除率分别为27.1%、32.4%和41.6%;取代基位置的不同使硝基苯甲酸的去除效果出现差异,其疏水性越强越易在EPDM膜中溶解和渗透;硝基苯甲酸的去除率和透过率与其辛醇/水分配系数和分子极化率正相关,与溶解度负相关;硝基苯甲酸的去除率可用分子极化率和偶极矩两个结构参数进行预测。     

生物滴滤塔净化苯乙烯废气的实验研究

采用生物滴滤(BTF)系统对含苯乙烯的有机废气进行了生物净化实验并研究该系统VOCs生物降解性能。实验表明,苯乙烯进气浓度低于20 mg/m3时BTF去除效率可达92%以上,出口苯乙烯浓度低于1.6 mg/m3,达到GB14554-1993中规定的排放标准;该BTF装置对苯乙烯的去除负荷在2.0 g/(m3.h)左右;系统稳定运行时循环液COD、浊度和pH等都保持稳定,无脱落生物膜积累现象;生物滴滤塔系统适宜的气液比为300;系统总压降约100 Pa,鲍尔环填料和聚氨酯发泡填料混合装填方式可以降低系统压降并有利于微生物挂膜。     

Preliminary study of acrylamide monomer decomposition during methane fermentation of dairy waste sludge

Polyacrylamide(PAM) used in sludge dewatering exists widely in high-solid anaerobic digestion. Acrylamide is registered in the list of chemicals demonstrating toxic, carcinogenic and mutagenic properties. Therefore, it is reasonable to ask about the mobility of such residual substances in the environment. The study was carried out to assess the impact of the mesophilic(39 ± 1°C) and thermophilic(54 ± 1°C) fermentation process on the level of acrylamide monomer(AMD) content in the dairy sludge. The material was analysed using high-performance liquid chromatography(HPLC) for quantification of AMD. The results indicate that the process of methane fermentation continues regardless of the temperature effects on the degradation of AMD in dairy sludge. The degree of reduction of acrylamide monomer for thermophilic fermentation is 100%, while for mesophilic fermentation it is91%. In practice, this means that biogas technology eliminates the risk of AMD migration to plant tissue. Moreover, it should be stressed that 90% of cumulative biogas and methane production was reached one week earlier under thermophilic conditions — the dynamics of the methanisation process were over 20% faster.     

基于本质安全的微反应器中苯乙烯聚合的数值模拟

重大化工事故往往是由多米诺效应引发的一连串故障而导致的。为实现苯乙烯聚合反应的本质安全,采用本质安全设计原则,设计了T型微反应器以替换传统釜式反应器。先通过计算流体力学(CFD)方法建立了三维稳态模型,再通过UDF(User Defined Functions)添加组分输运方程源项和能量方程源项,对苯乙烯自由基聚合反应进行了数值模拟,研究在微尺度条件下,反应温度、混合反应管道长度及形状对反应结果的影响。结果表明:由于微反应器可提高传热传质效率,在一定范围内反应温度可以控制在3 K以内;反应管道由0.15 m增长至1.5 m后,转化率可提高2倍左右;0.15 m直管形状改进为螺旋状后,转化率可至少提升4%。     

新型阳离子聚丙烯酰胺的合成及絮凝性能研究

以丙烯腈和二异丁烯为原料,通过里特反应,合成了具有较大空间体积、疏水性好的树枝状功能性单体,并通过质谱、核磁对其结构进行了表征。在复合引发体系的催化下,把功能性单体、丙烯酰胺(AM)和阳离子单体甲基丙烯酰氧乙基三甲基氯化铵(DMC)进行共聚合,合成了不同阳离子度的高性能阳离子聚丙烯酰胺并对其絮凝特性进行了研究。实验结果表明该絮凝剂具有很好的除油、除污效果,有望在污水处理领域得到实际的推广应用。     

仲丁醇对苯乙烯臭氧化反应生成二次有机气溶胶的影响:实验和模型研究

通过烟雾箱实验,研究了仲丁醇对苯乙烯臭氧化反应生成二次有机气溶胶(SOA)的影响.结果发现,在烟雾箱实验中,过量仲丁醇的加入导致生成SOA的产率明显下降.同时,结合MCM气相机理和气-粒分配理论,将Criegee中间体与醛类的双分子反应添加到箱式模型中模拟烟雾箱中SOA的生成过程.模拟结果表明,在没有仲丁醇存在的情况下,次级臭氧化物在SOA组分中占1/2左右的比例.仲丁醇的加入消耗了大量的·OH,同时使得[HO_2]/[RO_2]比值升高,影响自由基相关的反应机制,使得SOA产率下降.另外,研究发现,Criegee中间体与醛类反应的速率常数也是影响SOA生成模拟的一个重要参数,需要进一步开展相关的动力学实验和理论研究.     

Synthesis and identification of graft copolymers of wood pulp and styrene

Based on the graft copolymerization reactions of lignin and vinyl monomers, a series of graft copolymers of wood pulp and styrene (1-phenylethene) has been synthesized. The wood pulps used in this research are unbleached products produced by chemical, thermal, and mechanical pulping. All of them contain a high content of lignin (25–29 wt%). The grafting reaction is a free radical polymerization coinitiated by calcium chloride, hydrogen peroxide, and wood pulp in dimethylsulfoxide at 30°C. The effect of reaction temperature, reaction time, and the amount of the reactants on the conversion of monomer, yield of product, weight increase of pulp, and grafting efficiency of monomer has been studied. The grafted wood pulp was separated from homopolystyrene formed during the reaction by extraction of the reaction product with benzene in a Soxhlet apparatus for at least 48 h. The results show that after the reaction, the weight of all wood pulps was significantly increased and the weight increase of very high yield sodium bisulfite pulp (VHYS) was 333%. This proves that a part of the polymerized styrene was chemically bound to the wood pulp. The Fourier transform infrared (FTIR) spectra of the extracted products show absorbance peaks characteristic of both wood and polystyrene and, thus, provide strong proof of grafting. Grafting has completely changed the surface properties of the starting wood pulp from hydrophilic to hydrophobic, and under ordinary thermal compression conditions, thermoplastic composite objects of good uniformity can be made directly from reaction products which contain up to 52 wt% wood pulp.     

改性污泥活性炭对苯乙烯的吸附

以城市污泥为原料制备活性炭,对其进行改性,研究了改性前后的比表面积、表面酸碱基团、对苯乙烯的静态吸附容量、吸附穿透曲线、脱附活化能等吸附性能.结果表明,硫酸铜溶液浸渍改性后可使污泥活性炭比表面积明显提高,其中0.1 mol.L-1硫酸铜溶液浸渍改性的污泥活性炭较改性前的比表面积提高了32%(达704.7 m.2g-1).硫酸铝溶液和硫酸铜溶液浸渍改性可以使污泥活性炭表面酸性基团含量提高、表面碱性基团含量减少;对苯乙烯的静态吸附容量提高到改性前的两倍以上(分别达211.4 mg.g-1和178.8 mg.g-1)、对苯乙烯的动态吸附穿透时间由2 min提高到10 min以上、脱附活化能由2.94 kJ.mol-1提高到6 kJ.mol-1以上.改性后活性污泥炭的吸附性能得到明显提高.     

Enzyme-Based Vinyl Polymerization

In vitro enzyme-mediated polymerization of vinyl monomers is reviewed. Oxidoreductase enzymes have been used for the polymerization of styrene, derivatives of styrene, acrylates, and acrylamide in water and water-miscible co-solvents. Kinetic and mechanistic studies revealed that a ternary system (horseradish peroxidase, H₂O₂, initiator, or -diketone) is required for efficient polymerization and the initiator controls the polymer characteristics.