模拟土壤淋洗废液中重金属的选择性去除与淋洗液的回收研究

土壤淋洗废液中污染物的选择性去除是实现淋洗液回收的关键.本文以硫化钠（Na₂S）、乙基黄原酸钾（PEX）、二甲基二硫代氨基甲酸钠（DTC）作为重金属沉淀剂处理电子垃圾污染土壤模拟淋洗废液,在筛选出Na₂S作为理想重金属沉淀剂的基础上,研究初始pH值、反应温度、沉淀剂浓度等因素对Na₂S分离络合态重金属的影响,并通过软件模拟和产物表征等方式推测反应机理.结果表明：Na₂S对柠檬酸络合态重金属的分离顺序依次为Cu、Pb、Cd,符合硫化物溶度积原则;反应温度、初始pH值对Na₂S处理络合态重金属无显著影响,重金属去除率均保持在90%以上,柠檬酸的回收率约为95%;Visual MINTEQ模拟结果显示,S^2-投加前液相中重金属主要以H₂CA^-、HCA^2-和CA^3-结合形式存在,S^2-投加后液相中重金属则以HS^-和S^2-结合形式存在;扫描电镜及能谱（SEM-EDS）表明,S^2-与金属阳离子按物质的量比1：1生成硫化物沉淀物,沉淀主要呈团聚、成簇和圆片状存在;X射线衍射（XRD）分析结果表明,沉淀产物中存在CuS、CdS、PbS和CuPbS₂.本研究结果可为化学沉淀法处理重金属污染土壤淋洗废液提供技术参考.     

高原高寒污水处理系统的微生物群落特征

为研究高原高寒污水处理系统活性污泥的微生物群落结构及多样性,以拉萨、云南、四川的3座高原污水厂作为实验组,同时以重庆2座非高原污水厂作为对照,采用PCR-DGGE技术对比分析了高原与非高原污水厂的微生物特性.研究表明：高原污水厂样品与非高原样品在聚类中展现出了较为疏远的关系,微生物群落区别明显.受强紫外线辐照的抑制,高原高寒污水处理系统微生物多样性的平均水平显著低于非高原污水厂,较低的微生物多样性是导致高原高寒地区污染物去除效果不佳的一项重要原因.群落构成方面,共鉴定出16个优势菌属,对应Proteobacteria、Bacteroidetes、Firmicutes、Verrucomicrobia 4个门.组间差异分析结果发现,高原组中丰度显著偏高的菌属只有Prosthecobacter,该菌在污水厂内分布广泛,且能够适应高原低温的条件.对于大多数活性污泥微生物而言,高原强紫外线是不利的生存条件.因此,减少高原露天污水处理系统的紫外辐照,是提升污水处理效能的一个潜在措施.     

黑河流域底栖动物群落结构及水质评价

为了解黑河流域上中游底栖动物群落结构特征及其与环境因子之间的关系,于2018年8月对研究区域17个采样点的底栖动物和水体理化指标进行调查研究.共鉴定出底栖动物43种,其中节肢动物34种（79.1%）,软体动物7种（16.3%）,环节动物2种（4.6%）;就整个研究区域而言,优势种为大蚊（Tipulidae）、豆娘幼虫（Damselfly）、水蜘蛛（Argyroneta）、耳萝卜螺（Radix auricularia）、琥珀螺（Suecinea sp.）、白旋螺（Gyraulusalbus）,干、支流优势种分布趋势为干流（6种）优于支流（5种）;底栖动物平均密度和平均生物量分别为77ind/m²和3.7423g/m²现存量存在显著空间差异,整体上干流（1032ind/m²、60.0963g/m²）大于支流（276ind/m²、3.5233g/m²）,物种数干流（36种）大于支流（15种）;单因素方差分析显示,Shannon-Wiener多样性指数、Margalef丰富度指数及Pielou均匀度指数分布特征为干流大于支流.黑河流域上游支流和中游干流不同河段底栖动物物种组成呈空间异质性,而多样性指数对物种组成依赖性强,但因黑河流域底栖动物物种组成受自然因素和人类活动双重影响程度差异较大,使得Shannon-Wiener多样性指数、Margalef丰富度指数及Pielou均匀度指数不适合黑河水质评价.依据BI指数和综合污染指数评价表明,黑河上游支流水质优于中游干流.根据底栖动物与环境因子之间的相关矩阵分析并结合RDA分析表明：BOD₅、水温（WT）、电导率（EC）、DO、溶解性总固体（TDS）、COD_Mn及盐度是影响底栖动物群落结构的主要环境因子.     

酸性紫色水稻土颗粒有机质对镉的吸附特性

采集典型的酸性紫色水稻土（APPS）,从中分离出颗粒有机质（POM）,通过批量试验研究POM及其来源土壤Cd²⁺的吸附动力学、等温吸附和热力学特征,通过扫描电镜-能谱仪、傅里叶红外光谱仪等手段及吸附前后镉的形态变化的测定,研究了POM对Cd²⁺的吸附机制.结果表明：POM对Cd²⁺的亲和力远高于其来源土壤.POM及土壤对Cd²⁺的吸附动力学最优模型均为准二级动力学.Langmuir、Freundlich方程均能较好地描述其等温吸附特征,其中对POM,以Freundlich方程更优,表明POM对Cd²⁺的吸附属于多分子层的非均质吸附.吸附热力学参数△G^θ均小于0、△H^θ和△S^θ均大于0,表明吸附属于自发吸热过程.根据△H^θ值及解吸试验判定POM对Cd²⁺的吸附以化学吸附为主,土壤对Cd²⁺的吸附过程以物理吸附为主.吸附平衡后,土壤中可交换态镉比例提高,而POM中交换态和络合态镉比例增加.综上及吸附前后POM的表征结果说明,POM对Cd²⁺的吸附机制包括含氧官能团的络合、离子交换、阳离子-π键、沉淀作用和静电吸附.     

北方湖库沉积物重金属区域特征及生态风险评价

以白洋淀、衡水湖、于桥水库、松花湖、大伙房水库和小兴凯湖沉积作为研究对象,通过对北方六湖库沉积物中Cu、Zn、Pb、Cr、Ni等重金属元素进行分析,并与国内外其他水域重金属污染情况进行多因素比较,探讨了六湖库主要重金属污染源的差异性,区域分布特征以及与国内外其他水域污染的相似性和区别.结果表明,六湖库沉积物重金属污染处于中等偏下水平.六湖库之间主要重金属污染源存在差别.沉积物重金属含量未出现明显上升的趋势.其中Zn、Pb存在富集现象,但Pb含量与历史数据相比出现下降,Zn的含量与其他地区相比整体偏高.大伙房水库沉积物重金属污染较重,Cu、Zn、Pb、Cr、Ni含量平均值分别为56.28,142.3,17.44,97.9,44.44mg/kg.小兴凯湖沉积物重金属含量最低,Cu、Zn、Pb、Cr、Ni含量平均值分别为2.41,63.90,13.37,56.36,26.09mg/kg.六湖库综合风险评价结果为大伙房水库>于桥水库>白洋淀>衡水湖>松花湖>小兴凯湖,重金属整体潜在生态风险指数为低.     

2018年春节期间京津冀地区污染过程分析

为了解2018年春节期间京津冀地区空气污染情况,利用近地面污染物浓度数据、激光雷达组网观测数据,结合WRF气象要素、颗粒物输送通量和HYSPLIT气团轨迹综合分析污染过程.结果表明,春节期间出现3次污染过程.春节前一次污染过程,各站点PM_2.5浓度均未超过200μg/m³;除夕夜,廊坊站点PM_2.5峰值浓度达到504μg/m³,是清洁天气的26倍;年初二~初五,各站点PM_2.5始终高于120μg/m³,且污染主要聚集在500m高度以下,北京地区存在高空传输,800m处最大输送通量达939μg/（m³·s）,此次重污染过程为一次典型的区域累积和传输过程.京津冀地区处于严格管控状态时,燃放烟花爆竹期间PM_2.5峰值浓度可达无燃放时PM_2.5峰值的3.2倍.为防止春节期间重污染现象的发生,需对静稳天气下燃放烟花炮竹采取预防对策.     

Bioassay: A useful tool for evaluating reclaimed water safety

Wastewater reclamation and reuse has been proved to be an effective way to relieve the fresh water crisis. However, toxic contaminants remaining in reclaimed water could lead to potential risk for reuse, and the conventional water quality standards have difficulty guaranteeing the safety of reclaimed water. Bioassays can vividly reflect the integrated biological effects of multiple toxic substances in water as a whole, and could be a powerful tool for evaluating the safety of reclaimed water. Therefore, in this study, the advantages and disadvantages of using bioassays for evaluating the safety of reclaimed water were compared with those of conventional water quality standards. Although bioassays have been widely used to describe the toxic effects of reclaimed water and treatment efficiency of reclamation techniques, a single bioassay cannot reflect the complex toxicity of reclaimed water, and a battery of bioassays involving multiple biological effects or in vitro tests with specific toxicity mechanisms would be recommended. Furthermore, in order to evaluate the safety of reclaimed water based on bioassay results, various methods including potential toxicology, the toxicity unit classification system, and a potential eco-toxic effects probe are summarized as well. Especially, some integrated ranking methods based on a bioassay battery involving multiple toxicity effects are recommended as useful tools for evaluating the safety of reclaimed water, which will benefit the promotion and guarantee the rapid development of the reclamation and reuse of wastewater.     

An investigation of changes in water quality throughout the drinking water production/distribution chain using toxicological and fluorescence analyses

Changes in water quality from source water to finished water and tap water at two conventional drinking water treatment plants(DWTPs) were monitored.Beside the routine water quality testing,Caenorhabditis elegans-based toxicity assays and the fluorescence excitation–emission matrices technique were also applied.Both DWTPs supplied drinking water that met government standards.Under current test conditions,both the investigated finished water and tap water samples exhibited stronger lethal,genotoxic and reprotoxic potential than the relative source water sample,and the tap water sample was more lethal but tended to be less genotoxic than the corresponding finished water sample.Meanwhile,the nearly complete removal of tryptophan-like substances and newly generated tyrosine-like substances were observed after the treatment of drinking water,and humic-like substances were identified in the tap water.Based on these findings,toxic pollutants,including genotoxic/reproductive toxicants,are produced in the drinking water treatment and/or distribution processes.Moreover,further studies are needed to clarify the potentially important roles of tyrosine-like and humic-like substances in mediating drinking water toxicity and to identify the potential sources of these contaminants.Additionally,tryptophan-like fluorescence may be adopted as a useful parameter to monitor the treatment performance of DWTPs.Our observations provided insights into the importance of utilizing biotoxicity assays and fluorescence spectroscopy as tools to complement the routine evaluation of drinking water.     

Removal and desorption of chromium in synthetic effluent by a mixed culture in a bioreactor with a magnetic field

Two chromium removal experiments were performed in bioreactors with and without a magnetic field under the same conditions.The release of the chromium present in the biomass was tested in two experiments one with the initial pH of the medium and one with pH 4.0.The objective was to remove Cr(Ⅵ) and total Cr from the effluent,this was carried out by placing biological treatments of synthetic effluent contaminated with 100 mg/L of Cr(Ⅵ) in a bioreactor with neodymium magnets that applied a magnetic field(intensity85.4 mT) to the mixed culture.The removal of Cr(Ⅵ) was approximately 100.0% for the bioreactor with a magnetic field and 93,3% for the bioreactor without a magnetic field for9 hr of recirculation of the synthetic effluent by the bioreactor.The removal of total Cr was61.6% and 48.4%,with and without a magnetic field,respectively;for 24 hr.The desorption of Cr(VI) in the synthetic effluent was 0.05 mg/L,which is below the limit established by Brazilian legislation(0.1 mg/L) for the discharge of effluent containing Cr(Ⅵ) into bodies of water.The results obtained for the removal of chromium in synthetic effluent suggested that there was no significant influence on the viable cell count of the mixed culture.The desorption of Cr(Ⅵ) in synthetic effluent after bioadsorption of chromium by the mixed culture in the process of removal of chromium in bioreactors with and without a magnetic field was not significant in either of the experiments with different initial pHs.     

Recent advances in catalytic decomposition of ozone

Ozone (O₃), as a harmful air pollutant, has been of wide concern. Safe, efficient, and economical O₃ removal methods urgently need to be developed. Catalytic decomposition is the most promising method for O₃ removal, especially at room temperature or even subzero temperatures. Great efforts have been made to develop high-efficiency catalysts for O₃ decomposition that can operate at low temperatures, high space velocity and high humidity. First, this review describes the general reaction mechanism of O₃ decomposition on noble metal and transition metal oxide catalysts. Then, progress on the O₃ decomposition performance of various catalysts in the past 30 years is summarized in detail. The main focus is the O₃ decomposition performance of manganese oxides, which are divided into supported manganese oxides and non-supported manganese oxides. Methods to improve the activity, stability, and humidity resistance of manganese oxide catalysts for O₃ decomposition are also summarized. The deactivation mechanisms of manganese oxides under dry and humid conditions are discussed. The O₃ decomposition performance of monolithic catalysts is also summarized from the perspective of industrial applications. Finally, the future development directions and prospects of O₃ catalytic decomposition technology are put forward.