煤矸石自燃机理及其防治技术研究

煤矸石是我国最大的工业固体废弃物,煤矸石自燃是矿区主要的环境问题之一。并系统分析煤矸石的自燃机理,提出预防为主,防治为辅的对策,并重点介绍几种行之有效的煤矸石自燃的防治技术。     

两段式处理医院高浓度含氰废水的研究

以医院排放高浓度含氰(CN-)废水为研究对象,采用“硫酸亚铁+曝气”初级化学处理和ClO2二级深度氧化处理相结合的处理模式,不仅使含氰废水实现无毒化处理,而且使高浓度含氰废水实现资源化回收利用。试验表明,处理后的废水中CN-浓度达到国家排放标准GB8978-1996中的一级标准,为医院高浓度含氰废水的治理提供了一种新的方法。     

RuO2/La2O3/TiO2悬浮体系中直接耐晒黑G的光催化降解

钛酸丁酯为前驱体,采用溶胶-凝胶-浸渍法制备RuO2/La2O3/TiO2复合光催化剂,以紫外灯为光源,研究了催化剂组成、煅烧温度、溶液pH值等因素对直接耐晒黑G(DFBG)光催化降解的影响.结果表明掺杂量w(La2O3)1.39%、w(RuO2)0.12%、煅烧温度500℃(2 h)、溶液pH值7.3时,光催化活性最佳.当通气量为200 mL/min,催化剂投加量为150mg时,50 mg/L的DFBG溶液经60 min降解,其降解率近100%.DFBG的光催化降解服从Langmuir-Hinshelwood动力学模型,测得相应的动力学参数k=7.42×10-3mmol/L·min,K=19.54 L/mmol.     

非定态SO2制酸工艺在铅精矿烧结烟气治理中的应用

介绍了非定态SO2制酸工艺的特点、流程及其在铅精矿烧结烟气治理中的应用效果.该工艺具有良好的社会效益、环境效益和较好的经济效益,具有较高的推广应用价值.     

用动力波逆向喷射洗涤器脱除烟气中的二氧化硫

介绍了动力波逆向喷射洗涤器的构造及基本原理,并将这一新型洗涤技术应用于烟气脱硫。讨论了各种因素对采用石灰水作为洗涤液时的烟气脱硫率的影响,在pH为9．2、液气比为0．024条件下,脱硫率可达到90％。     

污水氯、二氧化氯消毒处理中水质及毒性变化的比较

分别从水质和毒性2方面比较了氯、二氧化氯消毒对污水的影响.结果表明:在水质特性方面,氯消毒对污水色度影响不大,而二氧化氯消毒明显降低了污水的色度;氯、二氧化氯消毒前后污水的DOC基本没有变化;氯消毒后污水的UV₂₃₀明显增加,二氧化氯消毒后污水的UV₂₃₀略有降低,当二者投加量均为30mg/L时,氯消毒使污水的UV₂₃₀增加约0.7cm^-1,二氧化氯消毒使污水的UV₂₃₀降低约0.05cm^-1.在毒性生成方面,氯、二氧化氯消毒产生的急性毒性均随消毒剂投加量的增加而增大,氯消毒产生的急性毒性明显高于二氧化氯消毒;氯消毒在一定程度上增大了污水的遗传毒性,而二氧化氯消毒在一定程度上降低了污水的遗传毒性.     

几种常见氧化剂对水中摇蚊幼虫氧化杀灭效能的试验研究

进行了几种水处理氧化剂———氯气、二氧化氯、臭氧对水体中摇蚊幼虫灭活效果的试验研究,并对原水中摇蚊幼虫经二氧化氯预氧化、混凝沉淀后的灭活效果进行了考察.结果表明,二氧化氯对摇蚊幼虫的灭活效果受水体pH值、有机物含量和藻类含量影响较小,与其它2种氧化剂相比,二氧化氯对原水中摇蚊幼虫具有更好的灭活作用;混凝烧杯实验证实,原水中的摇蚊幼虫经混凝沉淀后,与矾花沉降,不会对沉后的水产生影响;并且二氧化氯投加量1.0mg·L-1时,摇蚊幼虫在24h内死亡,投加量2.0mg·L-1时,死亡时间为6h;采用预投二氧化氯的水处理工艺可以起到控制摇蚊幼虫在沉淀池中孳生的作用.     

TiO2-PTFE光催化膜的制备及性能

以聚四氟乙烯（PTFE）乳液和纳米TiO2粉末为原料,采用无水乙醇为溶剂,经辊压后与不锈钢网结合,制备了多孔固定化TiO2-PTFE光催化膜。膜性能研究结果表明,m（TiO2）：m（PTFE）=4时,光催化反应处理质量浓度为20mg／L的苯甲酸溶液,2h内TOC去除率高达81．3％。通过扫描电子显微镜观察,TiO2-PTFE光催化膜表面平整,且孔隙分布均匀。TiO2最佳负载量为15mg／cm2。在优化反应条件下同悬浮态TiO2光催化反应体系相比,TiO2-PTFE光催化膜对光源有更高的利用率,表现出更佳的催化活性。     

Electric Swing Adsorption for CO2 removal from flue gases

One of the most important sources of CO₂ emissions are the fossil-fuel fired plants for production of electricity. Removal of CO₂ from flue gas streams for further sequestration has been proposed by the International Panel on Climate Change experts as one of the most reliable solutions to mitigate anthropogenic greenhouse emissions. When natural gas is employed as fuel, the molar fraction of CO₂ in the flue gas is lower than 5% causing serious problems for capture. The purpose of this work is to present experimental validation of an Electric Swing Adsorption (ESA) technology that may be employed for carbon capture for low molar fractions of CO₂ in the flue gas streams. To improve energy utilization, an activated carbon honeycomb monolith with low electrical resistivity was employed as selective adsorbent. A mathematical model for this honeycomb is proposed as well as different ESA cycles for CO₂ capture.     

Effect of steam hydration on performance of lime sorbent for CO2 capture

Lime is considered a feasible sorbent for the capture of CO₂ from large stationary sources. The positive attributes of a natural source material, low cost and lack of harmful by-products are offset by rapid deterioration in performance and high regeneration temperature. Performance can be improved by hydrating the lime using steam. We investigate a steam hydration process wherein lime is hydrated for 5 min at 300 °C and atmospheric pressure in a mixture of steam and CO₂. The experiments consisted of 10 capture cycles with 60% of the lime active at the end. Extrapolation using a decay model suggests a residual carbonation level of 48%, significantly higher than the 8% achieved by dry lime cycles. The cost of replacement sorbent under these conditions is less than $1/t of CO₂ captured. The hydrated lime process also reduces the thermal load, for heating and cooling, by half as well as the inventory, and therefore solids handling, by a factor 5 over dry lime. The introduction of the hydration reaction provides another exothermic reaction for heat management.