复合金属氧化物Cu-Co-Al低温催化水解HCN

采用共沉淀法制备了Cu-Al、Co-Al和Cu-Co-Al复合金属氧化物催化剂,考察了3种催化剂对HCN的催化水解性能,并通过XRD、BET、XPS和H2-TPR等对催化剂的结构和性能进行表征.结果表明, Cu-Co-Al催化剂展示最高的催化活性. 反应温度200℃,反应180min后, Cu-Co-Al、Cu-Al和Co-Al催化剂对HCN的转化率分别为95%,90%,10%;NH3生成量分别为122,118,18mg/m3.低结晶度、高分散性、高比表面积的催化剂有利于低温HCN水解.适量的表面分子氧含量、较高的Cu2+和Co3+含量、较低的还原温度是Cu-Co-Al催化剂具有较高的HCN低温水解活性的主要原因.     

DOC+CDPF对生物柴油燃烧颗粒排放特性的影响

以一台满足国五排放法规的车用柴油机为样机,研究加装氧化催化转化器DOC与催化型颗粒捕集器CDPF(DOC+CDPF后处理装置)前后,柴油机燃用B20燃料(燃料含20%体积掺混比的生物柴油)的颗粒排放特性.结果表明,在未加装该后处理装置时,该机排气颗粒数量浓度的粒径分布呈双峰形态,B20燃料的排气颗粒数量浓度的峰值粒径在10nm和50nm附近,纯柴油的排气颗粒数量浓度的峰值粒径在50nm和200nm附近.在颗粒粒径小于120nm的区域,该机燃用B20燃料的排气颗粒数量浓度大于纯柴油.加装该后处理装置后,该机排气颗粒数量浓度的粒径分布呈多峰形态,峰值粒径在10nm、20nm和60nm附近.加装DOC+CDPF后,不论是柴油还是B20燃料,与原机相比,柴油机排气颗粒总数量下降明显,其中60~200nm粒径范围的颗粒数量浓度降幅更为显著.在相同工况下,DOC+CDPF对柴油机燃用B20燃料的颗粒总数量净化效率高于纯柴油.     

Nanosized magnetite in low cost materials for remediation of water polluted with toxic metals,azo- and antraquinonic dyes

Nanosized magnetite has emerged as an adsorbent of pollutants in water remediation. Nanoadsorbents include magnetic iron oxide and its modifiers/stabilizers, such as carbon, silica, clay, organic moieties (polymers, aminoacids, and fatty acids) and other inorganic oxides. This review is focused on the recent developments on the synthesis and use of magnetic nanoparticles and nanocomposites in the treatment of contaminated water. The emphasis is on the influence of the iron oxide modifiers on some properties of interest such as size, BET area, and magnetization. The characteristics of these nanomaterials are related to their ability to eliminate heavy metal ions and dyes from wastewater. Comparative analysis of the actual literature was performed aiming to present the magnetic material, its preparation methodology and performance in the elimination of the selected pollutants. Vast information has been properly summarized according to the materials, their properties and preferential affinity for selected contaminants. The mechanisms governing nanomaterial’s formation as well as the interactions with heavy metals and dyes have been carefully analyzed and associated to their efficiency.     

铁基催化剂的微波水热处理对其SCR脱硝性能的影响

利用微波对共沉淀制备的铁铈钛复合氧化物催化剂前驱体进行水热处理,探讨了微波水热处理对铁基催化剂低温SCR脱硝性能的优化;并对微波水热处理条件的影响进行了正交分析.结果表明:对铁基催化剂前驱体进行微波水热处理,可提高其低温SCR脱硝性能,使其脱硝温度窗口向低温偏移;且微波水热处理的低温优化效果与催化剂中Fe/Ti摩尔比密切相关,Fe/Ti摩尔比越小,微波水热处理的低温优化越强;微波加热方式和微波辐射时间会影响微波水热处理对铁基催化剂SCR脱硝性能的低温优化;在相同微波辐射时间条件下,当P30逐渐变为P80,微波水热处理对铁基催化剂低温SCR脱硝的促进作用降低;在P30条件下,微波辐射15min使铁基催化剂具有最佳低温SCR脱硝活性.     

贵金属-稀土复合型催化剂的制备与性能研究

制备了净化车辆尾气的贵金属稀土复合型催化剂,对该催化剂进行了活性测试和结构表征.利用所制备的催化剂在摩托车上进行了性能研究.实验结果表明,采用催化剂后,可使车辆排放达到欧洲Ⅱ号标准,表明所研制的催化剂具有较好的应用价值.     

多金属氧酸盐电催化降解染料废水的研究

采用IR和XRD等手段对磷钼酸(PMo12)和3,3',5,5'-四甲基联苯胺(TMB)形成的电荷转移配合物(TMB)3PMo12进行表征,结果表明配合物中的杂多阴离子仍保留着Keggin结构.将配合物负载于γ-Al2O3上制备(TMB)3PMo12/γ-Al2O3负载型催化剂填充于电化学反应器中,考察电催化氧化体系降解酸性大红3R染料废水的效果.研究表明,(TMB)3PMo12/γ-Al2O3催化剂对酸性大红3R废水显示了良好的电催化活性,催化剂填充量为50g,负载量为0.6%时,在pH值为4,槽电压15.0V,曝气量0.14m3/h,极板间距3.0cm反应条件下,60min后,色度去除率达到79.7%,去除效果较传统二维平板和三维电解槽更高.     

Effects of a diesel oxidation catalyst on gaseous pollutants and fine particles from an engine operating on diesel and biodiesel

The effects of a diesel oxidation catalytic (DOC) converter on diesel engine emissions were investigated on a diesel bench at various loads for two steady-state speeds using diesel fuel and B20. The DOC was very effective in hydrocarbon (HC) and CO oxidation. Approximately 90%–95% reduction in CO and 36%–70% reduction in HC were realized using the DOC. Special attention was focused on the effects of the DOC on elemental carbon (EC) and organic carbon (OC) fractions in fine particles (PM_2.5) emitted from the diesel engine. The carbonaceous compositions of PM_2.5 were analyzed by the method of thermal/optical reflectance (TOR). The results showed that total carbon (TC), OC and EC emissions for PM_2.5 from diesel fuel were generally reduced by the DOC. For diesel fuel, TC emissions decreased 22%–32% after the DOC depending on operating modes. The decrease in TC was attributed to 35%–97% decrease in OC and 3%–65% decrease in EC emissions. At low load, a significant increase in the OC/EC ratio of PM_2.5 was observed after the DOC. The effect of the DOC on the carbonaceous compositions in PM_2.5 from B20 showed different trends compared to diesel fuel. At low load, a slight increase in EC emissions and a significant decrease in OC/EC ratio of PM_2.5 after DOC were observed for B20.     

UV185+254nm辐照下MnOx-TiO2分解甲醛与臭氧的机理

为提高185nm真空紫外光下甲醛与副产物臭氧的分解效率,以MnOx-TiO2复合催化剂取代TiO2光催化剂,发现甲醛与臭氧的转化率分别从44.7%和38.7%提高到77.5%和96.8%.研究比较了真空紫外光下和暗态下(加臭氧)甲醛与臭氧在MnOx-TiO2催化剂上的分解性能,及UV254nm下光催化分解甲醛的效率.结果表明,真空紫外光下气相活性氧物种的氧化与MnOx表面的臭氧催化氧化过程是甲醛分解的主要途径,而MnOx-TiO2上光催化氧化甲醛效率很低;副产物臭氧主要于MnOx表面活性位上由热催化分解.用真空紫外光辐照MnOx-TiO2催化剂,可提高MnOx催化分解臭氧的稳定性.     

非热等离子体与催化相结合去除气相低浓度苯系物

利用串齿线-简体构成的等离子体反应器,研究了非热等离子体及其与Pt/Al2O3或Mn/Al2O3催化剂组合作用下的苯系物转化率、COx产率和O3生成情况.结果表明.苯系物转化率排序为对二甲苯＞甲苯＞苯.产生非热等离子体的放电区后接Pt/Al2O3或Mn/Al2O3催化剂可提高苯系物的转化率,并使达到相同转化率所对应的电压降低1～2kV,等离子体与催化剂之间表现出明显的协同效应.非热等离子体放电与Pt/Al2O3或Mn/Al2O3催化剂组合后也有利于苯系物向COx转化及去除放电产生的O3,可使最大COx产率从80%分别提高到86%和100%,而反应器出口的最大O3浓度则从707mg·m-3分别降至339mg·dm-3和39mg·dm-3.经过等离子体反应器、催化剂以及两者组合方式的优化,等离子体放电协同Mn/Al2O3催化剂工艺有望成为处理气相低浓度有机物的实用方法.     

臭氧催化氧化控制溴酸盐生成效能与机理

比较了单独臭氧氧化和金属氧化物存在下臭氧催化氧化过程中溴酸盐的生成规律,探讨了催化剂投量、溴离子浓度、水的pH值、反应温度等对臭氧催化氧化控制溴酸盐生成的影响规律及在催化剂存在下控制溴酸盐生成的机理.结果表明,催化剂投量从0 mg/L增加到250 mg/L,能减少溴酸盐生成量85.1%;当溴离子浓度为0.5、1.0、2.0 mg/L时,臭氧催化氧化分别能减少溴酸盐生成量69.2%、83.5%和15.2%,溴离子浓度变化对催化作用的影响无明显规律;pH值升高会降低催化作用的效果;反应温度在5～25℃之间时,臭氧催化氧化能降低43%～59%的溴酸根生成量(溴离子浓度1.5 mg/L),反应温度变化不影响催化效果.催化剂通过抑制臭氧对次溴酸的氧化减少了溴酸根的生成量.催化剂表面的某些基团与硫酸根络合会削弱臭氧催化氧化控制溴酸根生成的能力,因此,利用催化剂控制溴酸盐的机理与催化剂表面性质密切相关.