基于条分模式的边坡可靠度近似计算方法

通过对边坡稳定分析方法中的条分理论和响应面法的研究,针对边坡可靠性计算往往没有明确的解析表达式,以及稳定性系数计算方法和响应面法(RSM)的特点,将响应面法中的有限元数值模拟以条分模式中的稳定性系数隐式方程的迭代计算方法代替,建立了条分模式下的边坡可靠性计算的极限状态方程,从而形成了一种新的边坡稳定可靠性响应面分析方法。本文提出的改进的响应面法原理简单,计算效率较高并具有一定的精度,适用于对边坡可靠度的近似计算。     

Optimization of the O3/H2O2 process with response surface methodology for pretreatment of mother liquor of gas field wastewater

• Real ML-GFW with high salinity and high organics was degraded by O₃/H₂O₂ process. • Successful optimization of operation conditions was attained using RSM based on CCD. • Single-factor experiments in advance ensured optimal experimental conditions. • The satisfactory removal efficiency of TOC was achieved in spite of high salinity. • The initial pH plays the most significant role in the degradation of ML-GFW. The present study reports the use of the O₃/H₂O₂ process in the pretreatment of the mother liquor of gas field wastewater (ML-GFW), obtained from the multi-effect distillation treatment of the gas field wastewater. The range of optimal operation conditions was obtained by single-factor experiments. Response surface methodology (RSM) based on the central composite design (CCD) was used for the optimization procedure. A regression model with Total organic carbon (TOC) removal efficiency as the response value was established (R² = 0.9865). The three key factors were arranged according to their significance as: pH>H₂O₂ dosage>ozone flow rate. The model predicted that the best operation conditions could be obtained at a pH of 10.9, an ozone flow rate of 0.8 L/min, and H₂O₂ dosage of 6.2 mL. The dosing ratio of ozone was calculated to be 9.84 mg O₃/mg TOC. The maximum removal efficiency predicted was 75.9%, while the measured value was 72.3%. The relative deviation was found to be in an acceptable range. The ozone utilization and free radical quenching experiments showed that the addition of H₂O₂ promoted the decomposition of ozone to produce hydroxyl radicals (·OH). This also improved the ozone utilization efficiency. Gas chromatography-mass spectrometry (GC-MS) analysis showed that most of the organic matters in ML-GFW were degraded, while some residuals needed further treatment. This study provided the data and the necessary technical supports for further research on the treatment of ML-GFW.     

Wastewater-nitrogen removal using polylactic acid/starch as carbon source: Optimization of operating parameters using response surface methodology

The use of PLA/starch blends for nitrogen removal was achieved. The influence of different operating parameters on responses was verified using RSM. The conditions for desired responses were successfully optimized simultaneously. Blends material may have a promising application prospect in the future. Nitrogen removal from ammonium-containing wastewater was conducted using polylactic acid (PLA)/starch blends as carbon source and carrier for functional bacteria. The exclusive and interactive influences of operating parameters (i.e., temperature, pH, stirring rate, and PLA-to-starch ratio (PLA proportion)) on nitrification (Y₁), denitrification (Y₂), and COD release rates (Y₃) were investigated through response surface methodology. Experimental results indicated that nitrogen removal could be successfully achieved in the PLA/starch blends through simultaneous nitrification and denitrification. The carbon release rate of the blends was controllable. The sensitivity of Y₁, Y₂, and Y₃ to different operating parameters also differed. The sequence for each response was as follows: for Y₁, pH>stirring rate>PLA proportion>temperature; for Y₂, pH>PLA proportion>temperature>stirring rate; and for Y₃, stirring rate>pH>PLA proportion>temperature. In this study, the following optimum conditions were observed: temperature, 32.0°C; pH 7.7; stirring rate, 200.0 r·min^-1; and PLA proportion, 0.4. Under these conditions, Y₁, Y₂, and Y₃ were 134.0 μg-N·g-blend^-1·h^-1, 160.9 μg-N·g-blend^-1·h^-1, and 7.6 × 10³ μg-O·g-blend^-1·h^-1, respectively. These results suggested that the PLA/starch blends may be an ideal packing material for nitrogen removal.     

基于TM影像的城市地表湿度对城市热岛效应的调控机理研究

论文以探究城市热岛效应调控机理为研究目的,以徐州地区1985-2010 年夏季四期Landsat TM影像为研究数据,应用单窗算法、K-T变换、空间叠加分析以及缓冲区分析等研究方法,对徐州市城市热岛时空变化特征进行了反演,重点对徐州市城市热岛强度的调控机理进行了分析并提出了通过K-T变换提取表示城市建成区内部植被与水体覆盖程度的城市地表湿度(ULSW)这一新指标.研究结果显示:城市地表湿度显著区对城市热岛效应起到了有效的调控作用,并且随着城市地表湿度值的提高,区域内部以及周围环境的温度都会随之下降.城市地表湿度指标对于城市热岛效应的调控水平具有一定的代表意义.     

森林地表可燃物含水率与海拔关系研究

大兴安岭天然林保护工程重点区域,也是森林火灾频发的重灾区。收集测定了177组森林地表可燃物含水率数据,整理成列联表,进行列联表分析。结果表明,所研究区域的森林地表可燃物在低海拔含水率较高,随着海拔的升高,含水率呈现明显的降低趋势。研究结果可为进一步建立更加精确的大兴安岭林区森林地表可燃物含水率预测模型提供理论基础,对于该林区火灾预防工作意义重大。     

矿山法双线地铁施工仿真及地表沉降数值分析

研究了左右双线矿山法隧道施工时的短期地面沉降。采用矿山法进行双线掘进,两隧道中心距13.2m,V级围岩CRD法进行施工,两侧隧道断面对称开挖。使用FLAC3D进行沉降分析,该软件能模拟地下隧道的掘进、支护和掌子面支护等。针对某地地质特征进行预测,这些特征是决定地面沉降量的关键因素。通过模拟左右双隧道对称掘进施工的暗挖隧道施工过程,得到了施工时的地面沉降规律,即沉降可分为两个阶段,且第一阶段沉降大于第二阶段沉降。最终为在市内建筑物密集区域修建地铁隧道提供安全可行的方法。     

一株苯酚降解菌的分离鉴定及响应面法优化其固定化

从太原市焦化厂废水活性污泥中分离、筛选出一株苯酚降解细菌,经生理生化反应和16S rRNA鉴定,该菌株为Diaphorobacter属细菌,命名为PD-07.代谢机制研究表明,苯酚可诱导该菌合成邻苯二酚2,3-加氧酶降解苯酚.为了提高该菌株对苯酚的降解率,以海藻酸钙为材料,对该菌株进行包埋固定化研究.首先采用Plackett–Burman实验设计筛选出影响固定化菌株苯酚降解率的关键因素,然后采用最陡爬坡实验逼近最大苯酚降解率响应区域.最后用Box–Behnken实验设计及响应面回归分析,应用二次方程对实验数据进行拟合得,拟合曲线与实验实测值相关性良好,最佳条件为海藻酸钠浓度3.83%(m/V)、CaCl2 0.3mol/L、菌胶比1:26.73、固定化时间2h、摇床转速180r/min、培养温度30℃、初始pH值7.2、液固比4.86:1,在此条件下苯酚降解率可达96.89%.     

脱硫石膏基羟基磷灰石对Cu2+吸附性能的研究

以燃煤电厂废弃物脱硫石膏(FGD)为主要原料,利用水热合成法制备羟基磷灰石(FGD-HA),利用XRD和SEM对FGD-HA的物相组成和微观形貌进行了分析和观察.通过静态吸附实验研究了吸附动力学、吸附等温线以及吸附热力学.结果表明,伪二级动力学模型相关系数为0.9998,是描述FGD-HA吸附Cu2+的最佳动力学模型,Cu2+在FGD-HA上的吸附平衡符合Langmuir等温线模型(R2=0.9846),热力学表明此吸附是自发吸热的过程.利用响应面分析法对Cu2+的吸附条件进行优化,得出投加量3.11g/L、pH值4.96、温度22.09℃、Cu2+初始浓度24.75mg/L为最佳吸附条件,此条件下Cu2+去除率预测值为100%,相同条件下开展的验证实验结果为97.4%,与预测值相接近说明模型的选择是实际可行的.     

多参数指示南极普里兹湾浮游植物的时空变化

以南极普里兹湾沉积物为研究对象,运用气相色谱技术,研究了生物标志物菜子甾醇、甲藻甾醇、长链烯酮对应指示的硅藻、甲藻、颗石藻等浮游植物的生产量和种群结构的历史变化,结合2001—2011年实测和遥感水体ρ(Chla)(Chla为叶绿素a)及SST(海水表层温度)数据,探讨了该湾浮游植物生产量时空变化特征及其影响因素. 结果表明:过去100多年间南极普里兹湾浮游植物总生产量(212.04~759.10 ng/g)〔以w(菜子甾醇)+w(甲藻甾醇)+w(长链烯酮)计〕和w(硅藻)所占比例(62.28%~87.13%)〔以w(菜子甾醇)所占比例计〕均呈上升趋势,而w(甲藻)所占比例(10.09%~27.98%)〔以w(甲藻甾醇)所占比例计〕和w(颗石藻)所占比例(1.97%~9.74%)〔以w(长链烯酮)所占比例计〕则呈下降趋势. 全球变暖背景下浮游植物种群变动通过改变南大洋对CO₂的吸收进而影响全球碳循环. 水体ρ(Chla)与沉积生物标志物指示的浮游植物总生产量均具有湾内高、湾外低的空间分布特征. 湾内ρ(Chla)与SST的年际变化趋势相似,二者以2002—2003年和2009—2010年相对较高,SST分别为-0.30和0.01 ℃,ρ(Chla)分别为1.69和2.31 mg/m3;以2001—2002年和2010—2011年相对较低,SST分别为-1.19和-0.95 ℃,ρ(Chla)分别为1.08和0.79 mg/m3,表明该湾SST变化可较明显地影响浮游植物的生长.      

稀酸预处理铜藻制备生物乙醇工艺

选取暖温带海洋生态环境生物修复的首选物种——铜藻(Sargassum horneri)为原料进行生物乙醇的制备,以稀硫酸水解后的还原糖收率为响应值,考察水解温度、液固比、水解时间和w(H₂SO₄)等参数对水解效率的影响. 为优化稀酸水解铜藻预处理的工艺条件,在单因素试验的基础上,利用Box-Benhnken中心组合设计法和响应面分析法,建立稀酸预处理工艺参数的回归模型,并与酶水解及发酵相结合验证了铜藻稀酸预处理效果. 结果表明:①稀酸水解铜藻的最优工艺参数. 水解温度为120 ℃,液固比为20∶1,水解时间为2.00 h,w(H₂SO₄)为4.50%. ②稀酸水解铜藻过程中各影响因素之间存在交互作用,水解时间和w(H₂SO₄)的非线性作用显著. ③对经最佳稀酸预处理工艺处理后的铜藻粉进行酶水解,其还原糖收率为44.05%,是未预处理下的8.14倍,并且后续进行发酵后,乙醇产率达7.80%,是未预处理下的2.00倍. 表明铜藻是一种潜在的生物乙醇原料,稀酸预处理方法对铜藻生物乙醇的制备行之有效.