生物型表面活性剂在煤表面润湿吸附规律研究

为了探讨生物型表面活性剂溶液在煤表面的润湿吸附规律,选定茶皂素、蔗糖酯、无患子和脂肽这4种结构性能不同的生物型表面活性剂作为研究对象,通过对4种溶液在煤表面接触角和表面张力进行测定,研究这4种生物型表面活性剂在煤表面的铺展系数、黏附功、黏附张力等润湿吸附参数。研究结果表明:脂肽的表面张力、接触角和黏附功均低于其他3种溶液,而其铺展系数高于其他3种溶液,说明脂肽在煤表面的润湿吸附性要强于茶皂素、蔗糖酯和无患子,但是黏附性则低于茶皂素、蔗糖酯和无患子。脂肽对煤体的润湿吸附性能优于另外3种生物型表面活性剂。     

Influence of additives in the end‐use mixes of tebufenozide on deposition,adhesion and persistence in spruce foliage

Abstract

A commercial flowable formulation of tebufenozide, RH‐5992 2F [N'‐t‐butyl‐N'‐(3,5‐dimethylbenzoyl)‐N‐(4‐ethylbenzoyl) hydrazine], was diluted with water, water and canola oil, and water and the methyl ester of canola oil, to provide six end‐use mixes with concentrations of 35 and 70 g of active ingredient (Al) litre^‐1. The mixes were applied at 70 and 140 g Al ha^‐1 over white spruce [Picea glauca (Moench) Voss] seedlings in a laboratory spray chamber and foliar concentrations of tebufenozide were determined over a 60‐d period. At intervals of time post‐spray, seedlings were sprayed with monosized droplets of Sunspray®11N as rainfall, and the amount of tebufenozide knocked off from foliage was determined. The potential energy of adhesion (PEA) of the Al particles on the foliage increased with time and varied according to the type of end‐use mix, its viscosity and the dosage sprayed.

The end‐use mixes were applied over white spruce trees under field conditions and persistence of tebufenozide was investigated. DT₅₀ values were influenced by the type of mix and dosage sprayed. Oil‐containing mixes and higher dosages increased the PEA of tebufenozide particles.     

Hopkinson压杆反射拉伸下PMMA动态破坏现象实验研究

利用Hopkinson压杆系统对PMMA变截面柱锥试样进行冲击加载，研究材料动态拉伸断裂特性和破坏机理。由于PMMA的拉压强度差别不大，采用圆柱状试件难以产生反射拉伸破坏，因此，将试样设计为圆柱锥状，实验时，将试样的圆柱端粘贴于输入杆上。实验结果表明，在一定的撞击速度下，由于应力波的汇聚作用，在试样锥段产生了反射拉伸破坏；当撞击速度较高时，在产生反射拉伸破坏的同时，试件中还产生了银纹区，随着打击速度的提高，银纹区域增大。同时根据断口的SEM观察，研究了材料的破坏机制。     

Selective flotation separation of plastics by chemical conditioning with methyl cellulose

The floatability of seven plastics (POM, PVC, PET, PMMA, PC, PS and ABS) in the presence of methyl cellulose (MC) and separation of plastics mixtures were investigated in this paper. It was found that the seven plastics can be separated into three groups by using the wetting agent MC. Group one includes POM and PVC. They are depressed at very low MC concentrations. Group two, including PET, PMMA and PC, has an intermediate floatability. Group three (ABS and PS) has a high floatability. They are almost not depressed within the given MC concentration range. In order to understand the mechanism of selective flotation of plastics and the chemical conditioning process, surface chemical factors, such as wettability of plastics and surface tension of flotation medium, and gravity factors, such as particle density and shape, were studied. It was found that the depressing effect of MC on plastics is ascribed mainly to its adsorption on the plastics surfaces. The MC molecules absorbed on plastics expose some of their polar groups oriented towards the aqueous phase, hence making the plastics surfaces hydrophilic. In addition, flotation selectivity for the plastics is dominated not only by wettability of plastics, but also by particle size, density and shape.     

混凝土工程灾害与钢纤维增强混凝土(SFRC)

随着混凝土强度的提高，对混凝土结构的安全性要求也更加突出了，然而，就混凝土结构而言，一直受物理性与化学性两大病害困扰，这两大病害是造成混凝土结构工程灾害的主要原因。而裂缝则是混凝土工程所有病害中员主要的因素，它大约占了70％的比例。此外，由于普通混凝土的抗拉强度一般都很低，拉应变与弯曲应变也很小，因此，普通混凝土结构中脆性破坏经常发生。为了改善普通混凝土的物理力学性能，人们一直在寻找各种方法和技术，钢纤维混凝土(SFRC)因此应运而生。近30年来，由于SFRC能显著改善混凝土的韧性，并可极大地提高混凝土的抗拉强度，SFRC目前被广泛应用于土木、水利、矿山、交通等诸多领域。本文对SFRC的阻裂与增强机理进行了综合阐述，同时，对SFRC在混凝土工程病害的修复中的应用进行了讨论，最后，给出了一些建议。     

复配表面活性剂水溶液处理甲苯气体的研究

以非离子表面活性剂吐温-20(Tween-20)为主表面活性剂,添加助表面活性剂十二烷基苯磺酸钠(SDBS)以及助剂氯化钠,形成复配水溶液吸收剂处理VOCs废气.以甲苯为VOCs的典型代表,研究了Tween-20,Tween-20/SDBS和Tween-20/SDBS/氯化钠3种水溶液吸收剂的临界胶束浓度(CMC)及其对甲苯去除率的影响.结果表明,当表面活性剂浓度达到CMC时,水溶液对甲苯的吸收效果开始明显增强,加入助表面活性剂SDBS和助剂氯化钠有利于甲苯的去除,同时可降低溶液的CMC,减少表面活性剂的用量,降低水溶液吸收法处理VOCs成本.当空气流量G为300mL/min、液体喷淋量L为75mL/min、进口甲苯浓度800mg/m3、温度T为30℃时,分别以Tween-20、Tween-20/SDBS(摩尔比1/4)和Tween-20/SDBS/氯化钠(摩尔比1/4/0.1)的水溶液为吸收剂,且浓度均为1CMC时,甲苯去除率分别为56%、70%和77%,三元复配表面活性剂水溶液的吸收效果最佳.     

黄铜温度计套管汞裂破坏的观察

对一起黄铜汞裂破坏的构件进行形貌和金相分析,结合能谱测试,讨论了汞裂破坏形式、汞裂破坏机制,汞裂与一般沿晶型应力腐蚀破裂及晶间腐蚀的差别.指出汞裂是汞或其蒸气沿应力作用造成的缺陷部位深入组织内部,通过物理或化学作用与原来的组织在晶界生成强度低的新相,破裂沿新相区域出现.