混凝-超滤工艺处理饮用水厂滤池反冲洗水和排泥水的效能

为探究饮用水厂滤池反冲洗水和排泥水的直接回用和处理后回用对水厂的影响及两类水处理过程中的差异,采用了污染负荷计算、实验室混凝小试和现场混凝-超滤中试装置对两类生产废水分别进行了研究。溶解性有机碳(dissolved organic carbon,DOC)、氨氮 (NH₄⁺-N)、Al³⁺和全氟类化合物(perfluorinated compounds,PFASs)的污染负荷计算结果表明生产废水直接回用会为水厂带来一定的额外负荷,其中排泥水和反冲洗水分别对PFASs和Al³⁺负荷贡献较大;通过对小试中浊度,UV₂₅₄以及5种荧光组分去除效果的对比,反冲洗水的混凝效果稍好于排泥水,同时10 mg·L⁻¹的聚合氯化铝为最佳混凝剂方案;在中试过程中,两类水中的浊度、有机物、Al³⁺和PFASs均可被有效去除,出水差异较小,但反冲洗水中的亲水性和小分子有机物使得其去除效果低于排泥水。总体来说,经过处理之后,两类生产废水均可回用,回用可有效减少废水排放量,提高水厂水资源利用率。     

基于高效絮凝沉淀池与翻板滤池组合工艺的工程案例

以银川市某水厂为例,评估高效絮凝沉淀池与翻板滤池组合工艺的工程应用效果。结果表明,高效絮凝沉淀池与翻板滤池组合工艺能够适应较大水质波动,具有一定抗冲击负荷能力。其浊度去除率和高锰酸盐指数 (以COD_Mn计) 去除率较高,出水水质满足《生活饮用水卫生标准》 (GB/T5749-2006) 。通过调整排泥量和污泥回流比,能够有效解决沉淀池泥位超标问题。根据翻板滤池的过滤负荷和滤水阀门的开度调整反冲洗周期,能够提高过滤效率,节约电耗。少量无烟煤滤料的流失对翻板滤池出水浊度无影响。本研究结果可为低温低浊水处理工程提供设计经验和工程案例参考。     

制粒及工艺优化对工程化阴燃治理含油污泥的影响

针对含油污泥含水率高、含油率高、渗透性差导致应用工程化阴燃处置技术的适应性差、处置能力低等问题,采用制粒手段强化含油污泥的预处理过程,并对其阴燃点燃及推进方式加以调整,旨在筛选出较优的预处理和阴燃工艺参数。通过小试实验探索了含水率对油泥制粒的影响,以及含水率、制粒状态、辅助燃料、阴燃启动方式和推进方向对阴燃的影响。结果表明,某含油废水治理产生的含油污泥可采用对辊挤出制粒的方式进行预处理,含水率宜控制在33%~35%;油泥经脱水或制粒均可增强阴燃稳健性;含水率较高时添加质量分数5%的稻壳,点燃耗时可缩短约40%,阴燃蔓延速度提升约70%;采用木炭间接启动阴燃也可显著缩短点燃耗时。本研究结果可为工程化阴燃治理油泥的工艺和设备设计提供参考。     

印染污泥与铁尾矿磁化焙烧回收铁资源

我国铁尾矿累计堆存量超1×10¹⁰ t,主要为难选的赤铁矿、褐铁矿、菱铁矿等,由于脉石矿物组成复杂,重金属等有害杂质含量高,难以直接资源化利用。利用铁尾矿与印染污泥共同磁化焙烧,回收铁尾矿和印染污泥中铁资源,研究了焙烧温度、焙烧时间和印染污泥掺烧量对铁品位和铁回收率的影响及作用机制。最佳焙烧条件为,800 °C、30 min、印染污泥掺烧量15%,对焙烧产物进行120 mT的湿法磁选,得到铁品位63.78%,回收率92.58%的铁精矿。铁尾矿中的针铁矿失水留下孔隙转化为赤铁矿,进而被还原为磁铁矿,其还原路径为FeO(OH)→Fe₂O₃→Fe₃O₄。SEM+MAPPING分析结果表明,磁化焙烧后赤铁矿和铝化合物的连生体被破坏,通过磁选可提升铁精矿品位及回收率。本研究可为印染污泥和铁尾矿的协同处理及资源化利用提供参考。     

毛毯印染废水处理技术研究

本文采用投菌水解(酸化)--接触氯化法处理毛毯印染废水.试验表明该工艺流程简单,处理效果好,出水水质稳定.当进水CODc在480～750mg/L范围变化时,出水CODDc稳定在100mg/L以下.其中,水解池对色度有较好的去除效果,同时可提高后续接触氧化池的处理效率;而CODc的去除则主要在接触氧化池进行.     

印染废水生物强化处理技术研究进展

印染废水是国内外公认的难处理的工业废水之一 ,活性污泥法是目前最常用的处理方法 ,但还存在诸多问题。在分析中 ,主要从生物强化技术、固定化微生物技术和微生物活性增加技术等方面 ,总结了废水生物处理技术强化研究进展 ,并讨论了今后的研究方向。     

Fate of ah receptor agonists during biological treatment of an industrial sludge containing explosives and pharmaceutical residues

GOAL, SCOPE AND BACKGROUND: Sweden is meeting prohibition for deposition of organic waste from 2005. Since 1 million tons of sludge is produced every year in Sweden and the capacity for incineration does not fill the demands, other methods of sludge management have to be introduced to a higher degree. Two biological treatment alternatives are anaerobic digestion and composting. Different oxygen concentrations result in different microbial degradation pathways and, consequently, in a different quality of the digestion or composting residue, It is therefore necessary to study sludge treatment during different oxygen regimes in order to follow both degradation of compounds and change in toxicity. In this study, an industrial sludge containing explosives and pharmaceutical residues was treated with anaerobic digestion or composting, and the change in toxicity was studied. Nitroaromatic compounds, which are the main ingredients of both pharmaceutical and explosives, are well known to cause cytotoxicity and genotoxicity. However, little data are available concerning sludge with nitroaromatics and any associated dioxin-like activity. Therefore, we studied the sludge before and after the treatments in order to detect any changes in levels of Ah receptor (AhR) agonists using two bioassays for dioxin-like compounds. METHODS: An industrial sludge was treated with anaerobic digestion or composting in small reactors in a semi-continuous manner. The same volume as the feeding volume was taken out daily and stored at -20 degrees C. Sample preparation for the bioassays was done by extraction using organic solvents, followed by clean up with silica gel or sulphuric acid, yielding two fractions. The fractions were dissolved in DMSO and tested in the bioassays. The dioxin-like activity was measured using the DR-CALUX assay with transfected H4IIE rat hepatoma pGudluc cells and an EROD induction assay with RTL-W1 rainbow trout liver cells. RESULTS AND DISCUSSION: The bioassays showed that the sludge contained AhR agonists at levels of TCDD equivalents (TEQs) higher than other sludge types in Sweden. In addition, the TEQ values for the acid resistant fractions increased considerably after anaerobic digestion, resulting in an apparent formation of acid resistant TEQs in the anaerobic reactors. Similar results have been reported from studies of fermented household waste. There was a large difference in effects between the two bioassays, with higher TEQ levels in the RTL-W1 EROD assay than in the DR-CALUX assay. This is possibly due to a more rapid metabolism in rat hepatocytes than in trout hepatocytes or to differences in sensitivities for the AhR agonists in the sludge. It was also demonstrated by GC/FID analysis that the sludge contained high concentrations of nitroaromatics. It is suggested that nitroaromatic metabolites, such as aromatic amines and nitroanilines, are possible candidates for the observed bioassay effects. It was also found that the AhR agonists in the sludge samples were volatile. CONCLUSIONS: The sludge contained fairly high concentrations of volatile AhR agonists. The increase of acid resistant AhR agonist after anaerobic digestion warrants further investigations of the chemical and toxic properties of these compounds and of the mechanisms behind this observation. RECOMMENDATION AND OUTLOOK: This study has pointed out the benefits of using different types of mechanism-specific bioassays when evaluating the change in toxicity by sludge treatment, in which measurement of dioxin-like activity can be a valuable tool. In order to study the recalcitrant properties of the compounds in the sludge using the DR-CALUX assay, the exposure time can be varied between 6 and 24 hours. The properties of the acid-resistant AhR agonists formed in the anaerobic treatment have to be investigated in order to choose the most appropriate method for sludge management.     

活性污泥反应器流态研究中示踪剂的选择

针对活性污泥反应器中的流态研究需要,通过备选示踪剂氯化锂、亚甲蓝和氯化钠的污泥吸附试验以及曝气静沉试验,研究了活性污泥对这3种示踪剂的吸附作用,以及示踪剂浓度对污泥处理效果的影响情况。结果表明,亚甲蓝易被污泥吸附,对试验数据干扰较大,且吸附亚甲蓝后,水样中污泥对COD_Cr的处理效率下降幅度达50%以上;氯化锂和氯化钠是离子型示踪剂,本身不易被吸附,投加后的活性污泥对COD_Cr的处理效率基本不变,保持在70%以上。从示踪剂投加量以及出水水质控制方面考虑,确定氯化锂为3种示踪剂中的最佳示踪剂。     

负载型纳米CuO/MnO2催化剂的制备及催化氧化深度处理印染废水

以酸改性凹凸棒土(ATP)为载体,活性炭为添加剂,制备负载铜、锰过渡金属氧化物的凹凸棒土-活性炭催化剂。以印染废水生化处理后出水的COD和色度为处理对象,考察了不同的催化氧化条件,即凹凸棒土与活性炭的比例、pH、H2O2和催化剂的投加量对印染废水深度处理效果,并利用SEM、XRD对催化剂进行表征。结果表明:在室温25 ℃时,催化剂载体中凹凸棒土与活性炭的比例为2∶1,H2O2加入量为理论加入量的2倍,即2.4 mL·L-1,pH值为4,催化剂的使用量为15 g·L-1时,COD和色度的去除率最佳,分别达到93%和90%。扫描电镜结果表明铜、锰以颗粒的形式负载在催化剂的表面,XRD结果表明在催化剂载体表面,活性组分的存在形式为CuO、MnO2。     

Fenton氧化联合人工湿地处理污泥中的重金属

针对单独应用Fenton氧化技术处理污泥的不足以及人工湿地在处理污水污泥方面的优势,以污水处理厂污泥浓缩池中含重金属污泥为对象,研究其依次经过Fenton氧化和人工湿地处理后重金属的去除效果及形态变化,以及污泥pH、TN和TP的变化情况。结果表明,Fenton氧化提高了污泥重金属的生物有效性,并促进了人工湿地对重金属的去除。Fenton氧化污泥经人工湿地处理后,Cu、Zn、Ni和Mn的去除率分别为67.2%、79.7%、37.0%和17.0%,与对照相比重金属的平均去除率提高了27.5%。经人工湿地处理后Fenton氧化污泥和原污泥重金属的生物有效性均降低。Fenton氧化污泥pH为4.4～4.6,经人工湿地处理后为6.2～7.1。人工湿地对Fenton氧化污泥和原污泥中TN的影响较小,而对TP表现出较高的去除率,2系统TP的去除率分别为51.1%和45.5%。