水性聚氨酯/UHMWPE纤维防弹复合材料无纬布预浸料成型工艺研究

本文比较了纤维预浸料不同结构形式与防弹性能的关系，并详细研究了水性聚氨酯／UHMWPE纤维防弹复合材料的含胶量、面密度和叠层方式等预浸工艺参数对材料防弹性能的影响，结合弹道实验分析了各因素作用的机制。     

催化氧化技术在橡胶废气处理中的应用

采用催化氧化技术处理热塑性丁苯橡胶( SBS)生产装置D线后处理单元废气,废气的非甲烷总烃去除率和环己烷去除率均达到98％以上,非甲烷总烃质量浓度达到DB11/447-2007《炼油与石油化学工业大气污染物排放标准》的要求(小于100 mg/m3).对SBS生产装置凝聚单元进行两釜流程改三釜流程后,催化氧化反应器入口非甲烷总烃质量浓度由( 3.84～5.82)×103 mg/m3降至( 2.48～2.63)×103 mg/m3,反应器出口非甲烷总烃质量浓度均小于50 mg/m3.凝聚单元改造并采用催化氧化技术处理废气后,每年节约费用约80万元.     

雷达吸波复合材料外观失效机理分析及控制方法研究

目的 解决多层泡沫夹芯结构的雷达吸波复合材料在环境效应下产生外观失效的问题。方法 制备3种类型的雷达吸波复合材料,开展典型自然环境试验。观察试验样品外观状态,并检测变形量。通过观察泡沫的微观组织形貌,检测热膨胀量变化及泡沫与树脂间的粘黏强度,用气相色谱质谱联用仪GCMS检测复合材料裂解气体成分,分析复合材料外观失效成因,并提出解决技术途径。结果 6个月自然环境试验后,1#、2#样品外观失效,而3#样品无明显变化。复合材料100℃裂解气体成分为氮气、二氯一氟乙烷、甲基膦酸二甲脂。4种泡沫在22～85℃的最大热膨胀量分别为–0.18%、–0.37%、–0.30%、–0.45%。环氧树脂与4种泡沫的粘黏强度在41～52N,而聚氨酯树脂达到了54～81N。结论 雷达吸波复合材料泡孔内残留气体的释放,是导致外观失效的根本原因。通过热处理工艺,减少样品残留气体量,并提升胶黏剂与泡沫的粘黏复合强度,是提升复合材料环境适应性的有效技术途径。     

Optimized processing power and trainability of neural network in numerical modeling of Al Matrix nano composites

In this research, an experimental study of reinforcing alumina nano-particles into the aluminum alloy matrix was implemented to verify the accuracy of modeling results obtained by feed forward neural networks. Artificial neural network combined with numerical technique were used to predict the various parameters of mechanical properties such as hardness, tensile and compressive yield stress, UTS and elongation percentage. Much experimentation were taken to discover a suitable number of hidden neurons, avoid detraction from the trainability and enable feed forward neural networks to solve more complex problems. The predictions were found to be consistent with experimental measurements.     

Effect of cooling rate and laser process parameters on additive manufactured Fe–Ti–C metal matrix composites microstructure and carbide morphology

In this paper, laser additive manufacturing (LAM) of Fe–TiC composite coating on AISI 1030 carbon steel is investigated using a numerical and experimental method. In order to have a desired result using LAM, it is crucial to understand the effects of the process parameters’ values on the TiC morphology and microstructure. For this purpose, the LAM process is numerically simulated in order to calculate cooling rate and peak temperature. Experimental data and numerical results are in good agreement in terms of the phase development. Results show that cooling rate plays a crucial role in phase transformation in the clad, however, final microstructure strongly depends on the cooling rate and powder's chemical composition. Two main carbide morphologies (i.e. dendritic and particulate) are studied and relevant cooling rates are detected. Based on this paper and developed map, it is possible to control the cooling rate in order to achieve specific carbide morphologies in the clad. In this study, scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) are used to characterize clads’ microstructure.     

废印刷线路板非金属粉-木塑复合材料性能

利用废印刷线路板非金属粉、木粉和聚氯乙烯制备复合材料,研究了复合材料的物理力学性能.结果表明:添加40目(0.35 mm)粒径非金属粉的非金属粉-木塑复合材料的各项性能整体优于添加20目(0.83 mm)粒径的复合材料;随着复合材料中40目粒径非金属粉替代量的增加,复合材料冲击强度、静曲强度整体呈下降趋势,内结合强度总体呈上升趋势, m(非金属粉)∶m(木粉)为30∶20时,静曲强度和内结合强度分别为31.74 和2.10 MPa,满足相应的国家标准和行业标准;40目粒径非金属粉-木塑复合材料的静曲模量随着非金属粉和木粉比率的增加先上升后下降,在m(非金属粉)∶m(木粉)为15∶35时达到最大值(2 853 MPa);24 h吸水厚度膨胀率和24 h吸水率分别优于硬质纤维板国家标准和地板基材用纤维板行业标准要求值.      

多功能富氧净水器在养殖领域的研究与应用

多功能富氧净水器的研究,采用聚丙烯微孔滤膜、复合活性炭纤维、酸性洗涤纤维及复合炭粒作为过滤吸附材料,并采用三碘树脂杀菌剂和载银活性炭复合杀菌剂进行灭菌,应用"综合过滤渗透法"的机理,将净化、矿化、灭菌、增氧等有机结合并进行反复的研究和试验,有效去除了水中微生物、污染物,降低化学需氧量和水的硬度,达到净化水质,增加水中溶解氧等预期效果,成功的应用在水产养殖等领域。     

HfB2-HfC-SiC 改性 C/C 复合材料的超高温烧蚀性能研究

目的制备HfB_2-HfC-SiC复相陶瓷改性C/C复合材料,并探究该材料的超高温烧蚀性能。方法采用化学气相渗透结合前驱体浸渍热解工艺制备HfC-SiC复相陶瓷改性C/C复合材料(C/C-HfC-SiC)和HfB_2-HfC-SiC复相陶瓷改性C/C复合材料(C/C-HfB_2-HfC-SiC),采用大气等离子烧蚀实验研究材料的超高温烧蚀性能。结果C/C-HfC-SiC和C/C-HfB_2-HfC-SiC复合材料2200℃线烧蚀率分别为1.54×10~(-3),1.38×10~(-3)mm/s。结论复合材料具有独特的微结构特征,亚微米级的HfB_2和HfC基体均匀弥散分布在SiC基体中。复合材料表面原位生成的液相SiO_2和固相HfO_2复合氧化物膜,既可以抵抗高速气流的冲蚀,又可以抵抗氧化性气氛的向内扩散,是复合材料具有优异超高温抗烧蚀性能的主要原因。     

等离子喷涂制备 ZrB2-SiC 复合涂层及其静态烧蚀性能

目的提高C/C复合材料的抗静态烧蚀性能。方法利用大气等离子喷涂技术在C/C复合材料表面制备ZrB_2-SiC复合涂层,对其进行1500℃的静态烧蚀实验。利用X射线衍射仪(XRD)、扫描电子显微镜(SEM)及能谱分析仪(EDS)对涂层的物相成分、微观形貌等进行检测分析。结果采用大气等离子喷涂制备的ZrB_2-SiC涂层是由熔融的粉末粒子紧密堆积而成,呈现典型的层状结构,涂层均匀完整地覆盖于C/C基体表面,厚度约为200μm。涂覆有ZrB_2-SiC复合涂层的C/C复合材料试样在1500℃分别氧化2,3,4 h后,试样依旧保持完整,C/C基体未遭受损伤,试样的质量增加率依次为3.39%,2.95%,4.25%。结论采用大气等离子喷涂技术能够在C/C复合材料表面制备出厚度均匀、结构致密的ZrB_2-SiC复合涂层,ZrB_2-SiC复合涂层使C/C复合材料的抗静态烧蚀性能显著提高。     

Enhanced adsorption of Methylene Blue from aqueous solution by chitosan-g-poly （acrylic acid）/vermiculite hydrogel composites

A series of chitosan-g-poly (acrylic acid)/vermiculite hydrogel composites were synthesized and used as adsorbents for the investigation of the e ect of process parameters such as vermiculite content, pH of dye solution, contact time, initial concentration of dye solution, temperature, ionic strength and concentration of surfactant sodium dodecyl sulfate on the removal of Methylene Blue (MB) from aqueous solution. The results showed that the adsorption capacity for dye increased with increasing pH, contact time and initial dye concentration, but decreased with increasing temperature, ionic strength and sodium dodecyl sulfate concentration in the present of the surfactant. The adsorption kinetics of MB onto the hydrogel composite followed pseudo second-order kinetics and the adsorption equilibrium data obeyed Langmuir isotherm. By introducing 10 wt.% vermiculite into chitosan-g-poly (acrylic acid) polymeric network, the obtaining hydrogel composite showed the highest adsorption capacity for MB, and then could be regarded as a potential adsorbent for cationic dye removal in a wastewater treatment process.