CDPF对重型柴油车颗粒物排放特性的影响

采用实验室底盘测功机和全流定容稀释采样系统（CVS）,搭载EEPS3090,开展了国三重型柴油车加装催化型颗粒物捕集器（CDPF）前后颗粒物排放因子和粒径分布比较,进一步分析了不同工况下CDPF对各模态颗粒物排放因子的影响.结果表明,重型柴油车加装CDPF前后基于单位里程的颗粒物数量排放因子分别为（2.7±1.1）×10¹⁵ km^-1和7.9×10¹⁴ km^-1,CDPF对颗粒物数量减排率为71.10%,其中对核模态和聚集态颗粒物数量减排率分别为28.70%和84.95%.随着车速的增加,CDPF对聚集态颗粒物数量减排效果良好,核模态颗粒物数量减排率急剧下降.高速工况下颗粒物在CDPF内部出现大粒径颗粒物向小粒径颗粒物转化的现象,导致核模态颗粒物数量排放因子的增加,应引起足够的重视.     

城市汽车年检碳排放数据挖掘及其应用研究

基于城市汽车年检中CO₂的过程动态检测数据,对小型汽油客车CO₂的排放因子和排放水平信息进行了挖掘,并与文献研究结果进行了对比.结果表明,从城市汽车年检数据中挖掘的CO₂排放结果可以作为研究城市机动车碳排放的重要参考依据;合理有效地利用汽车年检数据可以为城市车辆尾气排放的精准分级管控、城市交通运输碳排放达峰的量化分析,以及城市交通源的污染物和CO₂协同减排提供重要的数据支撑;从国Ⅰ到国Ⅴ不同排放阶段汽油车的常规污染物CO、NO_x和HC的排放水平下降非常明显,而对应的CO₂排放水平差异不大;CO₂排放因子随累计行驶里程、车龄、基准质量和排量的变化关系反映出,如果需要削减城市汽车碳排放水平,应鼓励使用基准质量小或者排量小的车辆,淘汰高油耗高排放的老旧车辆,鼓励公共绿色出行而降低单车活动水平,增加纯电动车辆优化车队能源结构.     

自适应滑模控制器的EPS侧风反向控制研究

为了研究在侧风影响下汽车正向助力转向偏移过大而威胁驾驶员行车安全的问题,提出一种将反向助力和自适应滑模控制器相结合的控制方法。该方法通过驾驶员转矩和汽车车速的配比设计反向助力特性曲线,并利用自适应滑模电机控制器控制电机输出助力转矩,使汽车在转向过程中,增加了驾驶员转向的阻尼感,也同时提高了驾驶员对转向电机的实时操纵性。将其应用到汽车EPS系统中,仿真结果表明,在不同的车速、风速下,采用反向控制策略不仅减小了方向盘角度、齿条位移,还减小了汽车横摆角速度,可以显著地改善汽车行驶的稳定性和安全性。     

化工园区安全监控系统研究

化工园区内重大危险源数量多、密度大,存在着发生重特大事故的现实性和可能性。因此,亟需建立化工园区安全监控系统对化工园区内的固定危险源、危险工艺过程、危化品车辆和公共区域重要部位进行动态监控和安全监管,预防和消除事故风险,并为化工园区安全监控与事故应急提供技术支持。提出了化工园区安全监控系统系统硬件架构,介绍了化工园区安全参数设置方法、安全监控流程和事故预警机制,提出了系统软件的总体架构和功能。     

石斛气生的兰科菌根组织结构及其对御旱研究

基于过去对铁皮石斛（Dendrobium candidum Wall．Ex Lindl．）气生的兰科菌根适应干旱环境胁迫机理的研究鲜为涉及,现开展了培养基质的不同水分质量分数（W（水）1=43．6％、16．8％、5．5％）对兰科菌根的外部形态以及内部组织结构影响的研究。研究结果表明：基质水分质量分数降低使石斛菌根外部形态发生多样变化;随着基质水分质量分数的不断降低,石斛的生长受到显著的抑制。当基质水分质量分数为5．5％时,石斛的多数生长指标均小于其它处理,但是根冠比（R／S）增加显著,高达2．22;通过不同切片多重镜检测定和图像分析,发现菌根的形态结构产生了天然的适应突变,独特的根被组织细胞层数多达5层以上,细胞壁相对加厚,细胞腔内网、羽状结构比其它两处理明显增多,石斛菌根通过形态结构的改变来适应水分胁迫并维持其生长发育,石斛菌根组织结构的这些改变大大提高了石斛御旱的能力;水分质量分数高低与菌根感染率呈负相关,越是干旱条件菌根真菌繁衍越活跃,菌丝团结构相持时间越长,菌根的这些适应性响应都提高了石斛的抗旱能力。     

Investigation of the effects of battery types and power management algorithms on drive cycle simulation for a range-extended electric vehicle powertrain

Fuel cell (FC) hybrid vehicle power trains are an attractive technology especially for automotive applications because of their higher efficiency and lower emissions compared to conventional vehicles. This study focuses on the design of an FC hybrid power train system and evaluation of its simulations for a given speed profile through two alternative power management algorithms (PMAs). Parameters suitable for a small vehicle were taken into consideration in the mathematical model of the vehicle. The proposed hybrid power train consists of an energy storage system, composed of a 4-kg battery pack (either lithium-ion (Li-ion) battery, nickel metal hydride, or nickel–cadmium) and a direct methanol fuel cell (DMFC) as the range extender. The PMAs basically aim to fulfill the power requirements of the vehicle and decide how to command the power split between the battery and the FC. The model comprising a DMFC, a battery, and PMAs was developed in MATLAB/Simulink environment. The polarization curve of the FC was obtained using a one-dimensional DMFC model. Vehicle power requirements for a drive cycle were calculated using the equations of longitudinal dynamics of vehicle, and the results were integrated into MATLAB/Simulink model. As a result of the simulations, methanol consumption, state of charge of the battery, and power output of the FC were compared for the PMAs. This comparison shows the effect of PMAs on the hybrid vehicle performance for three battery types. The results indicate that the vehicle range could be increased when proper strategy is used as PMA.     

A remote sensing system of vehicle emissions based on tunable diode laser technology

As being an effective real-time method of monitoring vehicle emissions on-road, a remote sensing system based on the tunable diode laser （TDL） technology was presented, and the key technologies were discussed. A field test in Guangzhou（Guangdong, China） was performed and was found that the factors, such as slope, instantaneous speed and acceleration, had significant influence on the detectable rate of the system. Based on the results, the proposal choice of testing site was presented.     

基于锡合金的水下机器人密封自修复系统设计

目的 解决水下机器人推进器密封系统在驱动电机轴高速旋转和高水压情况下,密封件易磨损失效导致发生漏水故障的问题。方法 利用余度设计思想,在原有密封结构的基础上,设计一种基于锡合金的水下机器人密封自修复系统,当原有密封结构失效漏水,密封自修复系统便控制限位锡合金块加热至融化,使锡合金块的限位作用消失,进而释放冗余密封圈,并通过拉簧的作用将冗余密封圈推至密封槽内,从而恢复推进器的密封功能。为验证设计的可靠性,又通过有限元软件ANSYS对密封自修复结构中影响密封性能的关键部件进行静力学分析。结果 关键部件的强度仿真结果均满足设计要求,在密封自修复实验装置箱体内注适量水,并施加2 MPa的水压保持一段时间,密封自修复系统成功启动,且其密封性能传感器未检测到其漏水。结论 密封自修复系统可在漏水的情况下顺利启动,并起到密封的作用,验证了设计的可行性。     

热带海洋大气环境氯离子浓度立体化观测技术研究

目的 对热带海洋环境氯离子开展立体化观测,掌握热带海洋环境下大气氯离子浓度在空间上的分布规律,为海洋大气环境下装备产品和重大工程服役环境研究提供立体化观测数据支撑。方法 在观测海岸线附近科学选点,采用无人机搭载远程控制大气采样器开展大气氯离子浓度立体化观测,对不同空间高度氯离子浓度分布规律进行分析。结果 成功采集万宁某海岸线附近1 km×300 m×100 m区域1 a以上氯离子浓度数据,通过GIS技术分析并建立了氯离子浓度分布三维场,实现了氯离子浓度可视化,并随离海距离、离地高度剖切显示。结论 海南万宁某区域海岸线附近氯离子浓度在冬季最大,夏季最低,且在一定观测范围内,随观测高度增加而先增大、后降低,随离海距离增大而逐渐降低。     

Experimental research of the dynamic behavior of the natural gas suspension pipeline aerial crossing during pigging process

Suspension pipeline aerial crossings (SPAC) are mainly used to carry pipeline segments over large obstacles that are not suitable for trenchless technologies. It may suffer great vibrations and displacements during the pigging process due to the dynamic pigging loads and insufficient constraints from cables. Based on similarity criteria, an experimental scale model based on the Nujiang natural gas SPAC was designed and established. The vibration and displacement of the scale model were measured under different pigging velocities and liquid deposit volumes. The experimental results reveal that the natural gas SPAC vibrates during the pigging process, but the displacement versus time forms a U curve instead of a sinusoidal like curve. The extremum of the displacement is positively related to the pigging velocity and liquid deposit volume. In particular, the extremum increases by 0.37% with a 1% increase in the pigging velocity, while the displacement increases by 0.62% with a 1% increase in the liquid deposit volume. Under certain pigging conditions, or with damaged constraint components, the displacement extremum could be unacceptable. A low pigging velocity and a short time interval between two pigging operations are suggested to guarantee the safety of the natural gas SPACs. Besides, based on the experimental data, an empirical formula is developed to obtain the SPAC displacement-time curve with consideration of the span length, the pipeline diameter, the pigging velocity, the length and holdup of the liquid column. This formula can help to determine a suspicious displacement overrun, and to develop a data basis for choosing a safe pigging scheme of SPACs. This research provides insightful information to understand the mechanism of the SPAC's dynamic response as well as a practical tool to calculate the SPAC's displacement during the pigging process.