The formation of dithionate during the iron(III)-catalysed autoxidation of sulfur(IV)-oxides

The iron(III)-catalyzed autoxidation of sulfur(IV)-oxides results in the formation of two different oxidation products of sulfur(IV): dithionate, S₂O₆²⁻, and sulfate, SO₄²⁻. The yield of these reaction products depends on the experimental conditions. Under the studied conditions ([Fe(III)] : [SIV)] = 1:10, pH = 2–4) dithionate is the minor reaction product. The formation of dithionate is influenced by the initial pH but not by the initial O₂ concentration. The presence of CO²⁺, Mn²⁺, and Ni²⁺ have no influence on the yield of dithionate, whereas in the presence of Cr³⁺ less and, in the presence of Cu²⁺, no dithionate is formed.     

Adsorption of naphthalene onto a high-surface-area carbon from waste ion exchange resin

A high-surface-area carbon (KC-1) was prepared from waste polystyrene-based ion exchange resin by KOH activation and used for naphthalene adsorption. The carbon exhibited a good hydrophobic nature with developed porous structure, favoring the adsorption of organic compounds. The Brunauer-Emmett-Teller surface area and total pore volume of KC-1 were 3442.2 and 1.68 cm 3 /g, respectively, which can be compared with those of KOH-activated carbons prepared from other precursors. Batch experiments were carried out to investigate the adsorption of naphthalene onto KC-1. The equilibrium data were analyzed by the Langmuir, Freundlich, and Polanyi- Manes isotherms and agreed with the Polanyi-Manes Model. The adsorption of naphthalene depended greatly on the porosity of the carbon, and the dispersive interactions between naphthalene and carbon could be relatively weak. The pH variation in aqueous solution had little effect on the adsorption process. The equilibrium time for 0.04 g/L of carbon dose was around 5 hr. Different models were used to evaluate the kinetic data and the pseudo second-order model was suitable to describe the kinetic process of naphthalene adsorption onto KC-1. Regeneration of spent carbon could be carried out effectively by alcohol treatment. The results indicated that KC-1 was a promising adsorbent for the removal of polycyclic aromatic hydrocarbons from aqueous solutions.     

Preparation of magnetic nanocomposite beads and optimizing the conditions for effective removal of U(VI) from aqueous solutions

Magnetic ion-imprinted polymers (IIPs) were prepared by precipitate polymerization and leached with HCl to remove uranium. Their ability to remove hexavalent uranium from wastewater effluents was studied. Batch adsorption studies to determine the optimum conditions of U(VI) removal were conducted at different levels of sample pH, sorbent amount, agitation time, and initial uranium concentration. It was observed that, under optimum conditions (i.e. pH 4, adsorbent amount of 50 mg, 45 min agitation time, and initial U(VI) concentration of 2 mg L^?1), the maximum removal of U(VI) cations was >98% and 80% for the magnetic IIP and the corresponding magnetic non-imprinted polymers (NIP), respectively. Langmuir and Freundlich isotherms were used to describe the adsorption of U(VI) onto magnetic IIP and NIP. The adsorption capacity of U(VI) was determined to be 1.06 and 0.85 mg g^?1 for the two isotherms, respectively. The order of selectivity was found to be U(VI) > Fe(III) > Pb(II). For six cycles of regeneration and reuse, the magnetic polymers maintained their stabilities with only a 4% loss in the extraction efficiency. The average extraction efficiencies of the magnetic polymers for the spiked acid mine drainage and sewage wastewater effluents were 71% and 58% for the magnetic IIP and NIP, respectively. From powder X-ray diffraction analysis, application of the Scherrer equation yielded magnetic nanoparticles of an average mean diameter of 11.9 nm. Thermo-gravimetric analysis revealed that the HCl-leached magnetic polymers had a magnetite residual weight of 5%.     

重离子辐照1200V碳化硅二极管漏电退化的缺陷分析

目的研究1200 V碳化硅二极管重离子辐照诱生缺陷对漏电流退化的影响。方法以SiC结势垒肖特基二极管(Junction Barrier Schottky Diode,JBSD)为样品,采用能量为208 MeV,LET=37.3 MeV·cm^2/mg的锗离子进行辐照试验,利用半导体器件分析仪对重离子辐照前后1200 V SiC二极管的电学特性进行测试,利用深能级瞬态谱仪(Deep Level Transient Spectrum,DLTS)进行缺陷分析。结果辐照后,二极管的正向IV特性和CV特性未发生明显变化,反向IV特性退化。DLTS测试结果显示,E0.4能级和Z1/Z2能级基本未发生变化,EH能级有展宽的现象。测试电压VM=-8 V,填充脉冲电压VF=-1 V条件下测得的EH能级浓度比VF=-4 V条件下测得的高。结论分析认为,EH能级的缺陷复杂,推测是两个或多个缺陷能级的叠加(EH4、EH5、EH6、EH7等),此处缺陷的复杂程度与漏电流的退化成正相关,且这些缺陷的所在位置接近SiC外延层的表面。     

太湖淤泥烧结砖的制备及其性能

以太湖淤泥和粉煤灰为原料,干燥后混合加湿搅拌,压制成40 mm×40 mm×40 mm的试样,经干燥后放入电阻炉中焙烧,测试分析了不同粉煤灰掺量和焙烧温度下淤泥烧结砖的吸水率、抗压强度、腐蚀性及重金属浸出等性能。结果表明:增加粉煤灰掺量,砖体吸水率增大,抗压强度降低;当粉煤灰掺量30%、烧结温度950℃时,淤泥烧结砖强度可达到13.6 MPa,满足国家承重墙(MU10)使用标准。砖体浸出液微偏碱性,但不具有腐蚀性,高温焙烧可使淤泥中重金属得到有效固化。     

离子色谱法测定水中无机阴离子水样的预处理

本文介绍了用离子色谱法测定无机阴离子，对污染严重的水样通常采用预处理柱法。论述了预处理柱的制备、再生，测定了预处理柱对重金属及有机物的去除率及无机阴离子的回收率。     

用弱碱性离子交换树脂分离2-萘磺酸的研究

介绍了采用弱碱性离子交换树脂回收2－萘磺酸废水中的2－萘磺酸的试验研究。进行了pH、交换温度、共存阴离子等影响因素的条件试验及树脂再生试验,在较佳条件下,2－萘磺酸交换吸附率达98％以上,洗脱率接近100％。     

湿法烟气脱硫中亚硫酸钙氧化技术的研究进展

分析了国内外湿法脱硫工艺中亚硫酸钙的氧化反应控制因素研究成果,指出浆液pH值一般控制在4．5—5,采用Mn^2＋作为催化剂时,CaSO3有较高的氧化效率。对我国亚硫酸钙氧化技术的继续研究提出了一些建议,为湿法脱硫工艺设计提供参考。     

磁性活性炭处理含铜废水

利用自制磁性活性炭对水中Cu(Ⅱ)的去除进行静态吸附研究,考察了吸附时间、Cu(Ⅱ)初始浓度以及磁性活性炭投加量对铜离子去除率的影响。结果表明,磁性活性炭投加量为3 g/L时,对铜离子的去除率达92.6%;磁性活性炭对铜离子的吸附在最初的20 min是一个快速吸附,去除率达到总去除率的90%以上;随着Cu(Ⅱ)初始浓度的增大,Cu(Ⅱ)的去除率逐渐减小,磁性活性炭吸附铜离子可用Langmuir吸附等温式和Freundlich方程描述;利用磁铁对溶液中磁性活性炭进行回收,回收率达到87%。     

关于化学需氧量测定中化学反应的研究

研究了高氯样品COD测定中的化学反应,发现测定中产生的白色沉淀是AgCl而不是HgCl2,并推断了Cl-在COD测定中的反应机理.讨论了AgNO3、HgSO4加入量对测定结果的影响,重点分析了当AgNO3不足与过量时的数据.当试样体积20.00ml,按0.4g HgSO4络合2000mg/LCl-的比例,投加HgSO4掩蔽10000mg/L Cl-可取得满意结果.