Carbonyl sulfide and dimethyl sulfide fluxes in an urban lawn and adjacent bare soil in Guangzhou, China

Carbonyl sulfide (COS) and dimethyl sulfide (DMS) fluxes from an urban Cynodon dactylon lawn and adjacent bare soil were measured during April–July 2005 in Guangzhou, China. Both the lawn and bare soil acted as sinks for COS and sources for DMS. The mean fluxes of COS and DMS in the lawn (–19.27 and 18.16 pmol/(m2 sec), respectively) were significantly higher than those in the bare soil (–9.89 and 9.35 pmol/(m2 sec), respectively). Fluxes of COS and DMS in mowed lawn were also higher than those in bare soils. Both COS and DMS fluxes showed diurnal variation with detectable but much lower values in the nighttime than in the daytime. COS fluxes were related significantly to temperature and the optimal temperature for COS uptake was 29°C. While positive linear correlations were found between DMS fluxes and temperature. COS fluxes increased linearly with ambient COS mixing ratios, and had a compensation point of 336 ppt.     

福州城市边缘区森林土壤重金属污染特征及评价

为掌握福州城市边缘区森林土壤重金属污染特征,选取10个典型区域作为研究对象,分析森林土壤中Zn、Mn、Cr、Pb、Cu 5种重金属的含量及分布特征,并采用单项污染指数和综合污染指数法对土壤进行质量评价,结果表明:Cr、Pb是该区土壤重金属污染最主要的元素;Zn、Cu、Pb、Cr含量随土层深度增加而减少,Mn则相反;Zn...     

动力与热力抬升对烟气抬升高度的影响分析

通过模式选择和计算,得出烟气抬升高度的增加与动能和热能的关系,表明当烟囱出口处风速分别为3 m/s、2 m/s和1 m/s时欲增加同样大小的烟气抬升高度,需要的动能比热能要高,结论认为烟气的热力提升比动力提升的贡献大。     

抚仙湖流域城镇污染分析及控制策略

对抚仙湖流域城镇生活污染、城镇径流污染及污水处理设施等进行了全面调查与分析,并提出了相应的污染控制策略。     

县级城市人居环境主客观指标体系与评价模型对比研究

本文对人居环境相关研究进行了阐述,并就城市人居环境指标体系与评价模型进行了分析研究。提出了人居环境质量主客观评价结合模型,其中指标体系包括四个一级指标和18个单项指标,并依据我国黄河三角洲高效经济区内14个县级城市2007年的调查统计资料,对人居环境客观建设水平和居民满意度进行了对比评价。运用因子分析法处理指标数据,问卷调查的方法进行满意度评价。评价结果科学可行,并揭示出影响县级城市人居环境的根本因素。     

城市环境保护中污水治理的相关问题研究

随着我国向工业型国家转型的进程加快,我国作为一个水资源贫乏的国家,水污染的问题日益突出。因此,对于我国城市污水处理问题进行研究探讨,对于实现我国可持续发展战略有着重大的意义。本文主要对目前我国城市污水处理中存在的问题进行了分析研究,并在此基础上,对我国的城市污水处理提出了一些有针对性地对策与措施。     

基于快速聚类方法分析常州市区PM2.5的统计特性

运用统计方法研究常州市区2013~2014年6个国控点六项基本污染物(SO_2、NO_2、CO、O_3、PM_(2.5)和PM_(10))月平均浓度变化,结果表明,除O_3外,其它五项污染物月平均浓度夏季较低冬季较高.颗粒物与风速之间的关系为PM_(2.5)浓度随风速的升高一直降低,PM_(10)随风速的升高浓度先降低后升高.采用快速聚类分析(k-means)并运用SWV和DIV指数对六项基本污染物进行分类,得到4个样本分类.与依据颗粒物化学成分或粒径谱对PM进行源解析方法不同,本研究更多是从PM_(2.5)与其它污染物相关关系以及污染程度等角度按照欧式距离进行分类.不同类中PM_(2.5)来源明显不同,类1中PM_(2.5)与化石燃料燃烧排放密切相关,类2与O_3密切相关,类3与城市不完全燃烧排放、区域灰霾污染密切相关,类4可以归类于城市"背景"类.快速聚类分析结果也表明常州市区PM_(2.5)有着复杂的来源.     

Evaluation of accuracy of linear regression models in predicting urban stormwater discharge characteristics

Stormwater runoff has been identified as a source of pollution for the environment, especially for receiving waters. In order to quantify and manage the impacts of stormwater runoff on the environment, predictive models and mathematical models have been developed. Predictive tools such as regression models have been widely used to predict stormwater discharge characteristics. Storm event characteristics, such as antecedent dry days （ADD）, have been related to response variables, such as pollutant loads and concentrations. However it has been a controversial issue among many studies to consider ADD as an important variable in predicting stormwater discharge characteristics. In this study, we examined the accuracy of general linear regression models in predicting discharge characteristics of roadway runoff. A total of 17 storm events were monitored in two highway segments, located in Gwangju, Korea. Data from the monitoring were used to calibrate United States Environmental Protection Agency＇s Storm Water Management Model （SWMM）. The calibrated SWMM was simulated for 55 storm events, and the results of total suspended solid （TSS） discharge loads and event mean concentrations （EMC） were extracted. From these data, linear regression models were developed. R2 and p-values of the regression of ADD for both TSS loads and EMCs were investigated. Results showed that pollutant loads were better predicted than pollutant EMC in the multiple regression models. Regression may not provide the true effect of site-specific characteristics, due to uncertainty in the data.     

Microstructure of 2205 duplex stainless steel joint in submerged arc welding by post weld heat treatment

The 2205 duplex stainless steel (DSS) is of both good properties austenitic steel and ferritic steel, which applies to the shipbuilding industry usually. In this paper, the OM, XRD and microhardness test methods are used to analyze the variation of submerged arc welded (SAW) joints with and without post weld heat treatment (PWHT). The research results show that the σ phase disappear in the fusion edge zone near heat affect zone (HAZ) and an increase in the welded center zone during the follow-up PWHT, while the amount of γ phase is decreased in the welded center zone with PWHT. A segregation distribution of some second phases is also found in the welded center zone after PWHT. There have two pick values of microhardness arise in the fusion edge zone and the welded center zone separately without PWHT. However, a maximum value of microhardness at the fusion edge zone near HAZ is disappeared and the other is still held at the welded center zone during PWHT. It can be attributed to the changes of second phases, element diffusions and particle segregation during PWHT. A developing mechanism is issued to demonstrate the second phases transferring of the 2205 DSS SAW joints by PWHT.     

Improvement of welding heat source models for TIG-MIG hybrid welding process

Tungsten inert gas-metal inert gas (TIG-MIG) hybrid welding process is an effective way to improve welding productivity and quality due to advantages of the two processes. Mathematical analysis is crucial to fundamentally understand this synergetic welding process. In this study, based on experimental visualization of arc behaviors, some assumptions are proposed to deduce adaptive plane and volumetric heat source models separately for each involved welding method first. The influence of torch angles on distribution of temperature and geometry of weld bead are calculated and compared with experimental results. It shows that this developed algorithm of heat source can be employed to accurately predict welding process whether the electrode gun is slanted backward or forward to the direction of welding. Then TIG-MIG hybrid welding process is simulated and analyzed without considering the attractive or repulsive force of two arcs. The characteristic of TIG-MIG welding process is discussed compared to single MIG. It lays the foundation for the further research on the interaction of the two arcs during TIG-MIG hybrid welding.