A solid-phase microextration-based sampling method was employed to determine the concentrations of 1,1,1-trichloro-2,2-bis(p-chlorophenyl)ethane (DDT) and its metabolites, 1,1-dichloro-2,2-bis(p-chlorophenyl)ethane (DDD), 1,1-dichloro-2,2-bis(p-chlorophenyl)ethene (DDE) and 1-chloro-2,2-bis(p-chlorophenyl)ethene (DDMU), in two estuarine bays, Daya Bay and Hailing Bay, of South China. Six DDT components including p,p′-DDT, o,p′-DDD, p,p′-DDD, o,p′-DDE, p,p′-DDE, and p,p′-DDMU were detected in Hailing Bay, while only p,p′-DDD was found in Daya Bay. p,p′-DDD was the most abundant DDT component in both bays, sharply different from the previous finding in the water column of the Palos Verdes Shelf, California, USA that p,p′-DDE was prevalent. In addition, the occurrence of p,p′-DDMU (with a range of 0.047-0.21 ng/L in Hailing Bay) has not been reported around the globe, and its presence in our study region appeared to stem from dehydrochlorination of p,p′-DDD, favored under aerobic conditions, but further investigations are clearly needed to confirm the mechanism for generation of DDMU in estuarine environments. 相似文献
An inexpensive and effective adsorbent was developed from waste tea leaves for the dynamic uptake of Pb(II). Characterization of the adsorbents showed a clear change between physico-chemical properties of activated tea waste and simply tea waste. The purpose of this work was to evaluate the potential of activated tea waste in continuous flow removal of Pb(II) ions from synthetic aqueous effluents. The performance of the system was evaluated to assess the effect of various process variables, viz., of bed height, hydraulic loading rate and initial feed concentration on breakthrough time and adsorption capacity. The shape of the breakthrough curves was determined for the adsorption of Pb(II) by varying different operating parameters like hydraulic loading rate (2.3–9.17 m3/h m2), bed height (0.3–0.5 m) and feed concentration (2–10 mg/l). An attempt has also been made to model the data generated from column studies using the empirical relationship based on the Bohart–Adams model. There was an acceptable degree of agreement between the data for breakthrough time calculated from the Bohart–Adams model and the present experimental study with average absolute deviation of less than 5.0%. The activated tea waste in this study showed very good promise as compared with the other adsorbents available in the literature. The adsorbent could be suitable for repeated use (for more than four cycles) without noticeable loss of capacity. 相似文献
Objective: A novel anthropomorphic test device (ATD) representative of the 50th percentile male soldier is being developed to predict injuries to a vehicle occupant during an underbody blast (UBB). The main objective of this study was to develop and validate a finite element (FE) model of the ATD lower limb outfitted with a military combat boot and to insert the validated lower limb into a model of the full ATD and simulate vertical loading experiments.
Methods: A Belleville desert combat boot model was assigned contacts and material properties based on previous experiments. The boot model was fit to a previously developed model of the barefoot ATD. Validation was performed through 6 matched pair component tests conducted on the Vertically Accelerated Loads Transfer System (VALTS). The load transfer capabilities of the FE model were assessed along with the force-mitigating properties of the boot. The booted lower limb subassembly was then incorporated into a whole-body model of the ATD. Two whole-body VALTS experiments were simulated to evaluate lower limb performance in the whole body.
Results: The lower limb model accurately predicted axial loads measured at heel, tibia, and knee load cells during matched pair component tests. Forces in booted simulations were compared to unbooted simulations and an amount of mitigation similar to that of experiments was observed. In a whole-body loading environment, the model kinematics match those recorded in experiments. The shape and magnitude of experimental force–time curves were accurately predicted by the model. Correlation between the experiments and simulations was backed up by high objective rating scores for all experiments.
Conclusion: The booted lower limb model is accurate in its ability to articulate and transfer loads similar to the physical dummy in simulated underbody loading experiments. The performance of the model leads to the recommendation to use it appropriately as an alternative to costly ATD experiments. 相似文献