Development of a static test apparatus for evaluating the performance of three PM2.5 separators commonly used in China

PM_(2.5) separator directly affects the accuracy of PM_(2.5) sampling.The specification testing and evaluation for PM_(2.5) separator is particularly important,especially under China's wide variation of terrain and climate.In this study,first a static test apparatus based on polydisperse aerosol was established and calibrated to evaluate the performance of the PM_(2.5) separators.A uniform mixing chamber was developed to make particles mix completely.The aerosol concentration relative standard deviations of three test points at the same horizontal chamber position were less than 0.57%,and the particle size distribution obeyed logarithmic normal distribution with an R~2 of 0.996.The flow rate deviation between the measurement and the set point flow rate agreed to within ± 1.0% in the range of -40 to 50℃.Secondly,the separation,flow and loading characteristics of three cyclone separators(VSCC-A,SCC-A and SCC112) were evaluated using this system.The results showed that the 50% cutoff sizes(D_(50)) of the three cyclones were 2.48,2.47 and 2.44 μm when worked at the manufacturer's recommended flow rates,respectively.The geometric standard deviation(GSD) of the capture efficiency of VSCCA was 1.23,showed a slightly sharper than SCC-A(GSD = 1.27),while the SCC112 did not meet the relevant indicator(GSD = 1.2 ± 0.1) with a GSD = 1.44.The flow rate and loading test had a great effect on D_(50),while the GSD remained almost the same as before.In addition,the maintenance frequency under different air pollution conditions of the cyclones was summarized according to the loading test.     

两种奥氏体不锈钢酸性盐雾腐蚀行为研究

目的研究0Cr18Ni9(钝化)不锈钢与0Cr18Ni10Ti(钝化)不锈钢在酸性盐雾条件下的腐蚀行为,为发动机零件选材及防护措施的改进提供依据。方法按GJB150.11A—2009《军用装备环境试验方法盐雾试验》进行,调节溶液p H到3.5±0.5,以24 h喷雾润湿+24 h干燥为一个循环,分别开展2(96 h)、4(192 h)、5(240 h)个循环的酸性盐雾试验。采用目视、称量、X射线衍射(XRD)、扫描电子显微镜(SEM)及能谱仪(EDS)对盐雾腐蚀后试样进行观察及分析。结果 0Cr18Ni9(钝化)与0Cr18Ni10Ti(钝化)两种奥氏体不锈钢均发生了轻微的腐蚀,主要为局部腐蚀及均匀腐蚀。结论两种金属在酸性盐雾条件下耐蚀性良好,且可满足目前海军型发动机对材料耐酸性盐雾腐蚀的要求,0Cr18Ni9(钝化)略优于0Cr18Ni10Ti(钝化)。     

布置压电阵列元件薄壁结构的振动控制技术研究

目的形成布置压电阵列元件薄壁结构的建模方法,通过时域仿真验证控制效果。方法通过有限元软件建立了布置压电阵列元件薄壁结构的动力学模型,采用ANSYS APDL参数化语言编写程序,自动生成带有压电阵列分流电路的薄壁结构有限元模型,并开展了动力学仿真研究。结果实现了连接分流电路的周期压电结构时域仿真,验证了压电阵列分流阻尼技术在薄壁结构振动控制中的有效性。结论所形成的布置压电阵列元件薄壁结构的建模和仿真方法,可为航空薄壁结构的振动控制提供技术支持。     

美军标MIL-STD-810与国军标150

分析了湿热环境对装备的影响及机理,介绍了美国军标810C/D/E/F各版本中湿热试验程序的特点,分析了这些程序的变化过程及其对GJB 150/150A湿热试验程序的影响,指出了810F/和GJB150A的湿热试验的目的仅是用以加速发现装备湿热问题,不再模拟寿命期遇到的复杂的温、湿度环境,实际上是一种加速试验。     

铸态珠光体基体球墨铸铁 S195曲轴的研制

针对生产实际要求,研究了微量元素加入量、开箱时间等对铸态球墨铸铁珠光体量及性能的影响,试验了铸态球墨铸铁曲轴的各种常规性能.     

减振复合钢板的成形性及其数值模拟研究进展

减振复合钢板是一种应用于汽车覆盖件方面的新型材料 ,有利于减振和减轻重量。介绍了其成形性和成形过程数值模拟的研究进展 ,并对未来发展进行了展望     

汽车尾气净化催化剂Ag/SAPO-34选择性催化还原NO

评价了Ag/SAPO-34分子筛催化剂选择性还原NO的活性,并运用漫反射红外光谱原位研究NO在Ag/SAPO-34催化剂上的选择性催化还原机理.结果表明Ag/SAPO-34有良好的低温活性,在氧气浓度为3.6%和温度为573K～673K时NO还原成N2的转化率达70%;催化剂活性随C3H6浓度的增加而升高,随空速的增加而稍有下降.基于漫反射红外光谱,认为反应机理为:NO、丙烯和氧反应,在Ag/SAPO-34催化剂上生成吸附的有机-氮氧化物,再由这些吸附物种分解成N₂,催化还原的关键是形成有机-氮氧化物中间体.氧的作用是充分促进丙烯活化以及增加NO_x吸附态含量,并且氧的存在是有效产生一系列中间物不可缺少的条件.     

唐山市大气中多环芳烃污染现状研究

通过污染源调查和采集样品分析得出唐山市大气中多环芳烃污染现状，与国内外一些城市相比较，了解目前唐山市大气中多环芳烃污染水平。     

阿尔山市TSP(总悬浮微粒)浓度变化与气象因素关系探讨

通过阿尔山市2005年大气中总悬浮微粒（TSP）的全年三个监测点的监测结果，结合采样时有关气象参数，着重对TSP与气象条件的关系做一下分析、研讨。