某垃圾焚烧厂投产前后周边土壤二英类化合物的分布

为研究垃圾焚烧厂运行对周边土壤二英类化合物（PCDD/Fs）含量的影响,采集了珠三角地区某垃圾焚烧厂投产前和投产后周边土壤样品,分析研究了该垃圾焚烧厂运行对周边土壤中PCDD/Fs含量和组分的变化.结果表明:①2012年（投产前）珠三角地区某垃圾焚烧厂周边土壤PCDD/Fs含量较低,范围为163~591 ng/kg（毒性当量范围为0.198~0.863 ng I-TEQ/kg,I-TEQ为国际毒性当量因子折算的毒性当量值）;2017—2019年（投产后）周边土壤PCDD/Fs含量范围为151~1.75×103 ng/kg（毒性当量范围为0.812~3.88 ng I-TEQ/kg）,与其他研究相比处于较低的水平.②投产后,距该垃圾焚烧厂较近（1.5 km）的采样点（S1）土壤PCDD/Fs含量逐年增长,在较远（5.2 km）但人口较密集的采样点（S3）土壤PCDD/Fs含量整体较高,但呈逐年下降趋势.③投产后,土壤中的17种PCDD/Fs单体组分中,毒性当量贡献率最高的单体为八氯二苯并二英（OCDD）和2,3,4,7,8-五氯二苯并呋喃（2,3,4,7,8-PeCDF）,二者毒性当量贡献率范围为15.7%~45.4%.④在同一采样点土壤PCDD/Fs单体组分年间差异不明显,但同一年份不同采样点差异明显.研究显示,目前该垃圾焚烧厂周边土壤PCDD/Fs含量较低,但仍需要长期监测其可能带来的风险.      

废塑料再生过程废水中微塑料去除模拟试验

微塑料是一种存在于不同环境介质中的新兴污染物,主要来源于废弃塑料制品,其存在污染范围广、潜在环境污染大的问题.废塑料再生企业生产废水中微塑料浓度远高于其他类型废水,对其生产废水中的微塑料进行处理具有重要的环境意义.模拟废塑料再生过程的生产废水并进行微塑料去除的絮凝沉淀试验,研究絮凝剂投加量、pH、水力快速搅拌条件的单因素和正交试验对废水中微塑料去除率及其各因素作用的影响.结果表明:①当PAC (聚合氯化铝)投加量为10 mL,PAM (聚丙烯酰胺)投加量为7 mL,pH为9,水力快速搅拌条件为100 r/min下维持40 s再200 r/min下维持40 s时,微塑料的总去除率最高,达91%.②PAC投加量是影响微塑料去除效果的主要因素,其次是pH.③微塑料的去除率与其本身的密度有关,密度大的ABS (acrylonitrile butadiene styrene,丙烯腈-丁二烯-苯乙烯)去除率最高,密度小的PE (polyethylene,聚乙烯)去除率最低.④不同粒径区间的微塑料去除率区别较大,粒径小(0.1~0.25 mm)的微塑料去除效果最好.研究显示,通过控制PAC和PAM的投加量、pH和水力搅拌速率等条件,能够有效将废水中的微塑料通过絮凝沉淀的方法去除,从而达到净化含微塑料生产废水的目的.      

内饰材料发射率对密封舱室热防护效率的影响

目的探究密封舱室热防护效率与其内饰材料表面发射率的关系,分析内饰材料发射率对其表面温度、舱室内温度的影响规律。方法采用自行设计的小型密封舱室和加热测量装置,对内饰材料表面及舱室内温度进行测量。结果当内饰材料发射率为0.09时,内饰表面温度为141.2℃,舱室内平均温度仅为90.8℃;内饰材料发射率为0.91时,内饰表面温度为124.4℃,舱室内平均温度为109.1℃。结论试样表面温度随材料发射率的提高而降低,舱室内部空气平均温度随材料发射率的提高而升高;试样表面温度与舱室空气平均温度的温度差随材料发射率的提高而减小;同时,相同试样表面温度与舱室平均温度的温度差随加热温度的提高而增加。     

温度和含水率对村镇垃圾焚烧烟气中有机物排放的影响

使用管式炉模拟村镇生活垃圾焚烧过程,研究不同焚烧温度和不同垃圾含水率条件下,村镇垃圾焚烧烟气中多环芳烃（PAHs）、氯苯及苯系物的生成和分布特性.结果表明,焚烧温度为550℃时,烟气中多环芳烃和氯苯的释放量最大,当温度小于550℃时,多环芳烃和氯苯的释放量随温度升高而增加,温度大于550℃时,多环芳烃和氯苯的释放量随温度升高而降低.高温焚烧不仅可以抑制烟气中多环芳烃的浓度及减少大分子量PAHs的排放,还能降低氯苯的释放量和氯代数,从而减小村镇垃圾焚烧烟气中的毒性;苯系物随着温度升高,由热解转变为高温合成,释放量也随着增加.水分对多环芳烃和氯苯有较大影响,对苯系物的影响较小.在400℃条件焚烧时,水分含量对多环芳烃总体上是促进的,而在850℃焚烧条件下则表现出抑制作用;而水分对氯苯则均表现出抑制作用,并且可以降低氯苯化合物的氯代数.     

有机垃圾厌氧消化泡沫产生机理及控制方法

为了分析厌氧消化泡沫的产生机理和控制方法有助于解决有机垃圾厌氧消化起泡问题,本文调研了近年来报道的厌氧消化系统起泡现象,并从底物特性、反应器构造及运行条件和消化过程相关特性3方面分析了不同底物、工艺和环境条件下厌氧消化反应器的起泡机理;讨论了丝状菌指数、表面张力、粘度、有机负荷、起泡趋势和泡沫稳定性等参数作为起泡风险评价指标的合理性;介绍和比较了4类消泡方法（物理法、机械法、生物法和化学法）的消泡原理及优缺点.目前,除污泥厌氧消化系统外,其他有机垃圾厌氧消化系统起泡的主要因素尚不明确,而这也限制了泡沫控制方法的开发.后期探索关键起泡微生物或研究生物表面活性物质与起泡的相关性,将有助于从新的角度揭示起泡机理,并开发出针对性更强的泡沫控制方法.     

不同基质生物炭对厌氧处理餐厨垃圾效能及微生态的影响

探究了剩余污泥（SS）、餐厨垃圾（FW）、玉米芯（CC）、甘蔗渣（BG）4种不同基质生物炭对厌氧生物处理餐厨垃圾效能的影响,对厌氧污泥的关键酶活性、微生物群落分布以及代谢途径等微生态进行了分析.结果表明,厌氧反应器分别加入4种生物炭后,COD平均去除率分别提高了29.49%、23.16%、29.42%、40.32%;傅里叶红外分析表明,投加SS生物炭组出水中羟基、酰胺基以及C-O-C伸缩振动峰减弱.4个厌氧反应器中厌氧污泥的乙酸激酶活性分别为0.40,0.42,0.96,0.98 μmol/g,表明投加CC与BG生物炭促进了餐厨垃圾的厌氧水解酸化过程;厌氧污泥胞外聚合物的蛋白质/多糖之比分别为0.415、0.56、1.89、2.8,投加CC、BG生物炭提高了污泥的稳定性.4个厌氧反应器中拟杆菌门、变形菌门、厚壁菌门为主要菌群,投加BG生物炭促进了变形菌门与厚壁菌门的生长;对于古细菌而言,甲烷杆菌属与甲烷丝菌属为优势种群,SS组的甲烷杆菌属丰度最高（53.48%）,而BG组中甲烷丝菌属丰度最高（42.72%）.KEGG功能分析表明古菌及细菌均以碳水化合物代谢、氨基酸代谢为主;而投加BG与SS生物炭后,微生物膜运输水平得到了提高.     

Induction of cytochrome P4501A and endocrine disrupting effects of school incinerator residues

The emission of the dioxin-like compounds from on-site waste incinerators of seven schools in Kyonggi Province of Korea was evaluated by determination of the cytochrome P4501A(CYP1A) catalytic activity and antiestrogenic activity using cell culturemicrobioassay. The residue samples were extracted in a Soxhlet apparatus using toluene for 20 hr. The concentrated crude extractswere fractionated with a basic alumina column. Dioxin-like compounds were then extracted. Induction of CYP1A activity in a rat(H4IIE) hepatoma cell line was used as indicator of biologicaleffect of incinerator residues and measured as 7-ethoxyresorufin-O-deethylase(EROD) activities. The EROD activities of fraction II extracts (one of the two extracts) in the H4IIE cells were from 0.044±0.002 to 4.424±0.351 ng-TEQ g^-1 (TCDD Toxicity equivalent), showing relatively high inducing capacity. Antisetrogenicity of the extracts was measured as decrease in E₂-induced cell proliferation. Most of the extracts showed antiestrogenic activity in MCF7-BUS cell.The TEQ levels of the incinerator residues and the antiestrogenicactivities were in good correlation, strongly suggesting that thepotent toxic emissions were indeed produced from the on-site school waste semi-incinerators and could cause the antiestrogenicity.     

Air Pollution and Heat Exposure Study in the Workplace in a Glass Manufacturing Unit in India

Air pollution in the workplace environment due to industrial operation have been found to cause serious occupational health hazard. Similarly, heat stress is still most neglected occupational hazard in the tropical and subtropical countries like India. The hot climate augments the heat exposure close to sources like furnaces. In this study an attempt is made to assess air pollution and heat exposure levels to workers in the workplace environment in glass manufacturing unit located in the State of Gujarat, India. Samples for workplace air quality were collected for SPM, SO₂, NO₂ and CO₂ at eight locations. Results of workplace air quality showed 8-hourly average concentrations of SPM: 165–9118 μg/m³, SO₂: 6–9 μg/m³ and NO₂: 5–42 μg/m³, which were below the threshold limit values of workplace environment. The level of CO₂ in workplace air of the plant was found to be in the range 827–2886 μg/m³, which was below TLV but much higher than the normal concentration for CO₂ in the air (585 mg/m³). Indoor heat exposure was studied near the furnace and at various locations in an industrial complex for glass manufacturing. The heat exposure parameters including the air temperature, the wet bulb temperature, and the globe parameters were measured. The Wet Bulb Globe Temperature (WBGT), an indicator of heat, exceeded ACGIH TLVs limits most of the time at all the locations in workplace areas. The recommended duration of work and rest have also been estimated.     

C OD在线分析仪比对中应注意的问题

分析了COD在线分析仪和实验室比对结果人为差异的原因是样品不均匀,在线分析仪取样装置滤过,取样层面和采样方式以及沉淀消除的方法不同造成的.提出应在相同的地点、层面和同一容器取样,用相同沉淀消除方法去除样品中氯离子干扰,保证两方法比对中使用水样的一致均匀,使测试结果正确可信.     

Environmental Impact Assessment of the Mining and Concentration Activities in the Kola Peninsula, Russia by Multidate Remote Sensing

On the Kola Peninsula, the mining and concentration industry exerts anthropogenic impact on the environment. Tailing dumps cause airborne pollution through dusting, and waterborne pollution due to direct dumping and accidental releases. The objectives were: (1) to analyse multidate satellite imagesfor 1964–1996 to assess the environmental pollution from themining and concentration activity in the Kola in temporal perspective; (2) to evaluate remote sensing methods for integrated environmental impact assessment. The area of mining and industrial sites steadily expands and amounted to 94 km² in 1996. The polluted water surface amounted to at least 150 km² through dumping in 1978 and to 106 km² in1986 due to dusting. Thus, the impact from the mining and concentration activity should be reconsidered as more significant than it was officially anticipated. In the past the main mechanism of pollution wasdirect dumping into the lakes. Currently and in future, airborne pollution after dusting storms will dominate. The effective recultivation of the tailing dumps will be a long-term process. For effective assessment of impacts from the mining and concentration industry, remote sensing methods should be complemented by in-situ measurements, fieldwork, and mathematical modelling.