攀钢炼钢厂提钒转炉浊环水水质稳定研究

在对转炉提钒浊环水质状况进行分析化验的基础上提出了水质调整措施,实施后有效地稳定了提钒浊环水质,改善了因提钒浊环酸性水质导致的缺陷,较好地满足了生产需要。     

纺织印染厂废水的深度处理中试及工程应用

采用曝气生物滤池(BAF)-臭氧-曝气生物滤池工艺对广东某大型纺织印染厂的常规水解酸化-接触生物氧化处理出水进行深度处理回用中试,在中试研究成功的基础上,设计了每小时处理5 t的工业化试验装置。试验运行结果表明:进水COD为100~150 mg/L,色度约80倍,浊度约10 NTU,在前BAF水力停留时间3 h,中间化学氧化池中臭氧投加量40 mg/L,后BAF水力停留时间2 h的情况下,经组合工艺处理后出水COD约30 mg/L,色度2倍,浊度<1 NTU,该工艺处理后的出水,可直接回用于对电解质浓度要求不高的生产工艺中,也可作为反渗透或纳滤膜的预处理工序。     

Combined alkaline and ultrasonic pretreatment of sludge beforeaerobic digestion

Alkaline and ultrasonic sludge disintegration can both be used as pretreatments of waste activated sludge (WAS) for improving the subsequent anaerobic or aerobic digestion. The pretreatment has been carried out using different combination of these two methods in this study. The effect was evaluated based on the quantity of soluble chemical oxygen demand (SCOD) in the pretreated sludge as well as the degradation of organic matter in the following aerobic digestion. For WAS samples with combined pretreatment, the released COD was in high level than those with ultrasonic or alkaline treatment. When combined with the same ultrasonic treatment, NaOH treatment resulted in more solubilization of WAS than Ca(OH)2. For combined NaOH and ultrasonic treatments with different sequences, the released COD were in the order: simultaneous treatment > ultrasonic treatment following NaOH treatment > NaOH treatment following ultrasonic treatment. For simultaneous treatment, low NaOH dosage (100 g/kg dry solid), short duration (30 min) of NaOH treatment, and low ultrasonic specific energy (7 500 kJ/kg dry solid) were beneficial for sludge disintegration. Using combined NaOH and ultrasonic pretreatment with the optimium parameters, the degradation efficiency of organic matter was increased from 38.0% to 50.7%, which is much higher than with ultrasonic (42.5%) or with NaOH pretreatment (43.5%) in the subsequent aerobic digestion at the same retention time.     

Pollutants removal and simulation model of combined membrane process forwastewater treatment and reuse in submarine cabin for long voyage

A laboratory scale test was conducted in a combined membrane process (CMP) with a capacity of 2.91 m3/d for 240 d totreat the mixed wastewater of humidity condensate, hygiene wastewater and urine in submarine cabin during prolonged voyage.Removal performance of chemical oxygen demand (COD), ammonia nitrogen (NH4+-N), turbidity and anionic surfactants (LAS)was investigated under di erent conditions. It was observed that the e uent COD, NH4+-N, turbidity and LAS flocculated in ranges of0.19–0.85 mg/L, 0.03–0.18 mg/L, 0.0–0.15 NTU and 0.0–0.05 mg/L, respectively in spite of considerable fluctuation in correspondinginfluent of 2120–5350 mg/L, 79.5–129.3 mg/L, 110–181.1NTU and 4.9–5.4 mg/L. The e uent quality of the CMP could meet therequirements of mechanical water and hygiene water according to the class I water quality standards in China (GB3838-2002). Theremoval rates of COD, NH4+-N, turbidity and LAS removed in the MBR were more than 90%, which indicated that biodegradationis indispensable and plays a major role in the wastewater treatment and reuse. A model, built on the back propagation neural network(BPNN) theory, was developed for the simulation of CMP and produced high reliability. The average error of COD and NH4+-N was5.14% and 6.20%, respectively, and the root mean squared error of turbidity and LAS was 2.76% and 1.41%, respectively. The resultsindicated that the model well fitted the laboratory data, and was able to simulate the removal of COD, NH4+-N, turbidity and LAS. Italso suggested that the model proposed could reflect and manage the operation of CMP for the treatment of the mixed wastewaters insubmarine.     

进口含铅物品的固体废物属性鉴别研究

以进口“未锻轧铅合金物品为例,对其固体废物属性进行鉴别研究. 在分析送检物品的基本理化特征、危险特性和产生属性的基础上,对未锻轧铅合金的固体废物属性进行综合分析. 结果表明,未锻轧铅合金不是合金金属,可能属于回收废铅酸电池的简单熔炼产物,虽然金属铅得到一定程度富集,但在该物品中仍含有大量杂质成分,在进一步生产中可能会对环境造成污染. 根据《固体废物鉴别导则》的判别原则,最终判定未锻轧铅合金属于固体废物,为海关部门的监管和执法提供了技术依据.      

双室微生物燃料电池不同接种条件下处理薯蓣素废水

比较了在5种不同接种条件下,利用双室微生物燃料电池(Microbial Fuel Cells,MFCs)处理薯蓣素生产废水的污染物去除和产电效果. 结果表明,该种废水可以用作微生物燃料电池的底物,在去除有机物的同时能够获得电能;采用全混合接种对污染物的去除效果最好,在350 h时COD_Cr去除率达到90%;采用污水处理厂厌氧污泥和薯蓣素废水驯化菌液混合接种的产电效果最好,在1 000 Ω的外电阻下得到了370 mV的输出电压,最大输出功率密度达到10.32 mW/m2;不同菌属在MFCs中的作用差别显著,产电与去污功能可能由不同优势菌属承担;初步富集到优势菌菌b,菌d和菌e;PCR-DGGE和DNA序列分析结果显示,菌d和菌e与β-变形菌具有较好的同源性.      

表面活性剂协同膨润土处理染料废水的研究

文章用两种阳离子表面活性剂溴化十六烷基三甲铵(CTMAB)、氯化十六烷基吡啶(CPC)与膨润土直接混合,协同处理模拟印染废水。研究了不同配比的CTMAB、CPC和膨润土混合物对靛红染料废水脱色的适宜条件,并与经过这两种表面活性剂改性的有机膨润土脱色效果作对比,初步分析了其作用机理。结果表明:表面活性剂(CTMAB和CPC)用量对脱色效果影响最大;表面活性剂协同膨润土体系的脱色效果明显优于其改性有机土,其中CTMAB混合膨润土体系效果最好,脱色率达99%以上;且表面活性剂混合膨润土体系的脱色效果受pH值和处理时间变化的影响较小,沉降速度快,表现出良好的吸附、脱色、絮凝沉降的协同效应。     

金属波纹填料在废油处理中应用的研究

文章主要对其结构特征进行剖析,并对波纹板在油液处理过程中的作用原理进行分析。通过两种油水分离材料进行真空脱水试验,真空脱水第一次循环中,金属波纹板的脱水率为79.12%,较传统折叠丝网脱水率高21%,证明金属波纹填料对废油真空脱水有良好的效果。最后通过两种不同规格的金属波纹板填料进行真空脱水试验,证明比表面积较大的350Y波纹板填料在废油脱水中并不优于比表面积较小的250Y金属波纹板填料。     

湿地植物在城镇污水处理系统中的作用特性研究

将不同类型湿地植物如凤眼莲、荇菜、稗草、黑藻、皇竹草、美人蕉等,引入城镇污水处理系统,考察其对污染物的去除效果和在湿地组合系统中的作用特性。盆栽实验发现,虽然植物对污水N、P营养元素的直接去除率分别只有14.0%～59.4%和8.6%～55.2%,但植物通过过滤、截留及加强有机物降解转化的作用,对水体中污染物的去除具有协同效应,使水体N、P的总去除率分别达65.4%～83.8%和43.5%～69.5%。将植物引入组合处理系统,中试实验结果表明,水体TN、TP和COD月平均去除率分别高达80.4%、74.3%和81.3%。与常规生化处理系统相比,处理效果大为增强,生化反应的能耗相对减少,出水水质较稳定,使湿地组合系统成为一种去N除P,防止水体富营养化的有效处理方法。     

构建湿地系统水力学参数的设计模型研究

构建湿地污水处理系统的水力学参数对于其功能的发挥起着非常重要的作用。在探讨构建湿地主要水力学设计参数的基础上,根据描述构建湿地污染物去除的几类机理模型:一级动力学模型、连续完全混合反应器模型、Monod动力学模型、Ergun公式以及对流-弥散模型,分别导出了相应的构建湿地污水处理系统水力学设计参数的计算模型并分析了不同设计模型的特点。