几种腐殖填料生物滤池COD去除效能比较研究

分别采用腐殖垃圾、泥炭、煤炭等腐殖填料及河沙构筑生物滤池,处理模拟废水,比较研究其COD去除效能及降解特征,为工艺填料改性提供理论依据。几种填料的扫描电镜分析图显示腐殖垃圾及泥炭以团聚体三维空间结构为主;煤炭与河沙表面粗糙程度较小,且主要由颗粒状物质构成。稀释平板涂布法分离出各生物滤池中发挥主要作用的微生物共3种,各系统菌落数量有差异,但种类相同。3种腐殖填料生物滤池在进水有机物浓度为500 mg/L及1000 mg/L时均有较理想的有机物去除效率。3种腐殖填料生物滤池中泥炭构筑的腐殖填料生物滤池有机物比降解速率最小,因而微生物比增长速率最小,微生物增长和自身氧化最易趋向于动态平衡,对应的饱和水力渗透系数最大,滤池最不易发生堵塞,最有利于腐殖填料生物滤池长期稳定运行,证明泥炭是一种优良的生物介质。     

地面浓度反推法计算石化企业无组织排放源强

对某石化企业储罐区和原油脱酸装置区的无组织排放非甲烷总烃进行监测,对监测数据进行Pearson相关分析,运用地面浓度反推法计算源强。实验结果表明：原油脱酸装置区各采样线浓度间的相关性好,反推出的源强较为准确,50,100,150 m采样线的反推源强非常接近,分别为21.68,21.60,19.76 t/a;而储罐区监测浓度的相关性不佳,该区域的非甲烷总烃无组织排放源可能不单一,不适用地面浓度反推法计算其源强。     

QSPR prediction of chromatographic retention times of pesticides: Partition and fractal indices

The high‐performance liquid‐chromatographic retentions of red‐wine pesticide residues are modeled by structure–property relationships. The effect of different types of features is analyzed: geometric, lipophilic, etc. The properties are fractal dimensions, partition coefficient, etc., in linear and nonlinear correlation models. Biological plastic evolution is an evolutionary perspective conjugating the effect of acquired characters and relations that emerge among the principles of evolutionary indeterminacy, morphological determination and natural selection. It is applied to design the co‐ordination index that is used to characterize pesticide retentions. The parameters used to calculate the co‐ordination index are the molar formation enthalpy, molecular weight and surface area. The morphological and co‐ordination indices barely improve the correlations. The fractal dimension averaged for non?buried atoms, partition coefficient, etc. distinguishes the pesticide molecular structures. The structural and constituent classification is based on nonplanarity, and the number of cycles, and O, S, N and Cl atoms. Different behavior depends on the number of cycles.     

实验室率定法测算长江南通段污染物降解系数

污染物降解系数是确定水环境容量的关键参数之一,本文采用实验室率定法,采集长江南通段的水样,分别于6℃、10℃、16℃、20℃室温下,在实验室内进行周期为20天的室内水质分析,根据室内水质分析结果,测算出不同温度下长江南通段"十二五"减排的约束性指标化学需氧量、氨氮的降解系数,并定性分析了长江水体中污染物本底浓度、可生化性、pH值等环境因子对污染物降解系数可能发生的影响。     

单体米黄大理石矿粉对小麦产量及各器官重金属含量的影响

采用盆栽法,研究大理石矿粉对小麦产量及对成熟期小麦根、茎叶、果实中重金属含量的影响。结果表明:添加大理石矿粉会显著影响小麦的生长及产量(P<0.05),添加矿粉的量不大于60g/kg时,小麦的结实小穗数、穗粒数、千粒重和产量随添加量的增加而增加,而含量再继续增大时,对小麦产量的促进作用将减弱;低含量的大理石矿粉能缓解Pb、Cu、Zn对小麦的毒害,而高含量的对小麦的影响各异,小麦各器官中重金属Cd、Cr与添加大理石矿粉含量呈显著正相关;重金属对小麦各器官的影响排序,根:Cd>Cr>Pb>Cu>Zn,茎叶:Cd>Cr>Cu>Pb>Zn,果实:Cd>Cr>Pb>Zn>Cu。在大理石开采区应该采取一定的措施,避免大量的大理石矿粉散入周围的耕地。     

Photo-dissociation of dimethylamine by KrBr excilamp

A study of dimethylamine photo-dissociation in the gas phase has been conducted using UV radiation delivered from a KrBr^* excilamp, driven by a sinusoidal electronic control gear with maximum emission at wavelength of 207 nm. The electrical input power and radiant power of the lamp were measured to determine their effects on the degradation. The influence of flow velocity and initial concentration of dimethylamine were also examined. In order to evaluate the photo-dissociation process comprehensively, several parameters were investigated, including removal efficiency, energy yield, carbon balance and CO₂ selectivity. It is shown that the removal efficiency increases with enhanced input power and decreased gas flow rate. A high removal efficiency of 68% is achieved for lamp power 102 W and flow velocity 15 m³ h⁻¹. The optimum dimethylamine initial concentration is around 3520 mg m⁻³, for which the energy yield reaches up to 442 g kW h⁻¹ when the input power is 65 W. In addition, two chain compounds (1,3-bis-dimethylamino-2-propanol; 3-penten-2-one, 4-amino) and three ring organic matters (1-azetidinecarboxaldehyde, 2,2,4,4-tetramethyl; N-m-tolyl-succinamic acid; p-acetoacetanisidide), were identified by GC–MS as secondary products, in order to demonstrate the pathways of the dimethylamine degradation.     

Electrochemical determination of anaerobic microbial decay coefficients

The biokinetics of attached and suspended bacteria are an essential component of activated sludge models, anaerobic digestion models and biofilm models. These parameters are often assumed or “confirmed” based on the goodness-of-fit of the bioprocess models. Using a microbial fuel cell with a baffled reactor chamber, the attached- and mixed-growth microbial decay coefficients were evaluated under anaerobic conditions. The capability for real-time voltage recording allows easy and accurate measurement of the anaerobic microbial decay coefficients (b_L, lysis-regrowth approach), which were determined to be 0.11 ± 0.01 and 0.15 ± 0.01 d⁻¹ for attached (to anode) and mixed (present in the anode chamber) growth microorganisms, respectively. The corresponding half-saturation constants using glucose as a substrate were 204 ± 10 and 123 ± 1 mg COD l⁻¹. Hence, like an oxygen uptake rate-based approach to measure the microbial kinetics under aerobic conditions, the electrochemical recording provides an attractive method to measure anaerobic microbial decay coefficients.     

Behavior and prediction of photochemical degradation of chlorinated polycyclic aromatic hydrocarbons in cyclohexane

The photochemical degradation of 11 chlorinated polycyclic aromatic hydrocarbons (ClPAHs) and the corresponding 5 parent PAHs was examined to simulate the compound’s fate on aerosol surfaces. All the ClPAHs and PAHs decayed according to the first-order reaction rate kinetics. The photolysis rates of ClPAHs varied greatly according to the skeleton of PAHs; the rates of chlorophenanthrenes (ClPhes) and 1-chloropyrene were higher than those of corresponding parent PAHs, whereas chlorofluoranthenes, 7-chlorobenz[a]anthracene and 6-chlorobenzo[a]pyrene were more stable under irradiation compared to respective parent PAH. Considering the photoproducts of ClPhes detected, the oxidation could occur immediately at positions of the highest frontier electron density. Finally, the quantitative structure-property relationship models were developed for direct photolysis half-lives and average quantum yields of the ClPAHs and parent PAHs, in which the significant factors affecting photolysis were E_LUMO+1, total energy and surface area, and E_LUMO, E_LUMO − E_HOMO and total energy, respectively.     

Solubility of toluene, benzene and TCE in high-microbial concentration systems

We report measurements of solubility limits for benzene, toluene, and TCE in systems that contain varying levels of biomass up to 0.13 g mL⁻¹ for TCE and 0.25 g mL⁻¹ for benzene and toluene. The solubility limit increased from 21 to 48 mM when biomass (in the form of yeast) was added to aqueous batch systems containing benzene. The toluene solubility limit increased from 4.9 to greater than 20 mM. For TCE, the solubility increased from 8 mM to more than 1000 mM. Solubility for TCE (trichloroethylene) was most heavily impacted by biomass levels, changing by two orders of magnitude as the microbial concentrations approach those in biofilms.     

Laboratory longitudinal diffusion tests: 2. Parameter estimation by inverse analysis

This study focuses on the verification of test interpretations for different state analyses of diffusion experiments. Part 1 of this study identified that steady, quasi-steady and equilibrium state analyses for the through- and in-diffusion tests with solution reservoirs are generally feasible where the tracer is not highly sorptive. In Part 2 we investigate parameter identifiability in transient-state analysis of reservoir concentration variation using a numerical approach. For increased generality, the analytical models, objective functions and Jacobian matrix necessary for inverse analysis of transient-state data are reformulated using unified dimensionless parameters. In these dimensionless forms, the number of unknown parameters is reduced and a single dimensionless parameter represents the sorption property. The dimensionless objective functions are evaluated for individual test methods and parameter identifiability is discussed in relation to the sorption property. The effects of multiple minima and measurement error on parameter identifiability are also investigated. The main findings are that inverse problems for inlet and outlet reservoir concentration analyses are generally unstable and well-posed, respectively. Where the tracer is sorptive, the inverse problem for the inlet reservoir concentration analysis may have multiple minima. When insufficient measurement data is collected, multiple solutions may result and this should be taken into consideration when inversely analyzing data including that of inlet reservoir concentration. Verification of test interpretation by cross-checking different state analyses is feasible where the tracer is not highly sorptive. In an actual experiment, test interpretation validity is demonstrated through consistency between theory and practice for different state analyses.