Fast and efficient aqueous arsenic removal by functionalized MIL-100(Fe)/rGO/δ-MnO2 ternary composites: Adsorption performance and mechanism

Because of its significant toxicological effects on the environment and human health,arsenic(As) is a major global issue.In this study,an Fe-based metal-organic framework(MOF)(Materials of Institut Lavoisier:MIL-100(Fe)) which was impregnated with reduced graphene oxide(rGO) by using a simple hydrothermal method and coated with birnessitetype manganese oxide(δ-MnO_2) using the one-pot reaction process(MIL-100(Fe)/rGO/δ-MnO_2 nanocomposites) was synthesized and applied successfully in As removal.The removal efficiency was rapid,the equilibrium was achieved in 40 min and 120 min for As(Ⅲ) and As(Ⅴ),respectively,at a level of 5 mg/L.The maximum adsorption capacities of As(Ⅲ) and As(Ⅴ) at pH 2 were 192.67 mg/g and 162.07 mg/g,respectively.The adsorbent revealed high stability in pH range 2-9 and saturated adsorbent can be fully regenerated at least five runs.The adsorption process can be described by the pseudo-second-order kinetic model and Langmuir monolayer adsorption.The adsorption mechanisms consisted of electrostatic interaction,oxidation and inner sphere surface complexation.     

A comparison of hydrocarbons emission from engine running 85# gasoline and M-100 methanol fuel

Increasing global interest in methanoi fuel has led us to investigate the exhaust emissionsof its engine. Analysis of its inorganic and organic emissions. such as CO. NO_x and hydrocarbons(total HC) have been widely reported. This paper presents an analysis of more than 20 kinds ofhydrocarbons in the emissions obtained from a spark-ignition Shanghai car running 85^# gasoline anda comparison with emission from a Santana test car running M-100 methanol fuel. A set ofenrichment method has also been described. Test results show that at the current stage of methanolengine development the concentration of individual hydrocarbon including some poisonous substancesis lower than those of normal gasoline engine.     

S-100 protein and neuron-specific enolase in amniotic fluid as markers of abdominal wall and neural tube defects in the fetus

The aim of this study was to determine whether there is increased leakage of neuron-specific enolase (NSE) and S-100 protein into amniotic fluid in pregnancies with neural tube defects, since both these proteins are produced by neural tissue, and to compare the value of these substances for detecting such defects with that of the more conventional techniques of alpha-fetoprotein (AFP) and acetylcholinesterase (AChE) gel electrophoresis. Amniotic samples from 25 mid-pregnancies (15–17 weeks' gestation) with neural tube defects (14 with open spina bifida and 11 with anencephaly) and from seven mid-pregnancies with abdominal wall defects were compared with a control material consisting of 80 amniotic fluid samples from 80 consecutive mid-pregnancy amniocenteses, with normal karyotypes and AFP concentrations. All of the above cases of abnormalities were primarily detected through increased AFP levels in the amniotic fluid. Amniotic fluid samples from 13 pregnancies with fetuses with autosomal chromosomal abnormalities and seven amniotic fluid samples contaminated with blood were also included in the investigation. It is concluded from the results that the conventional AFP assay combined with AChE gel electrophoresis is the best method for screening amniotic fluid for neural tube defects and defects of the abdominal wall. Neither NSE nor S-100 assay alone proved to be superior for the detection of these cases in mid-trimester amniotic fluid. The S-100 assay, however, could give additional information in cases where AChE gel electrophoresis is not decisive; for example, in samples contaminated with blood.     

DDTC—TX—100胶束增溶直接光度法测定水中低含量铜

ＴｒｉｔｏｎＸ１００对ＤＤＴＣ（二乙基二硫代氨基甲酸钠）与铜反应生成的络合物Ｃｕ（ＤＤＴＣ）２有增溶增敏作用,建立了低含量铜直接光度测定法。操作简便快速,选择性、精密度和回收率均较好,相对标准偏差为０８％～４３％,回收率为９６％～１０６％,摩尔吸光系数ε＝６４×１０３Ｌ／（ｍｏｌ·ｃｍ     

新型MIL-100(Fe)基MOFs材料的制备及其对Sr2+的吸附

采用水热法和溶剂热法制备了金属有机骨架材料——MIL-100(Fe)和MIL-100(Fe)-DMA.利用FTIR、XRD、SEM、XPS和N₂吸附/脱附对材料结构进行了表征.通过静态吸附实验,探究了初始Sr²⁺浓度、吸附时间、溶液pH值和不同共存阳离子对材料吸附性能的影响,研究了两种材料对Sr²⁺吸附过程的吸附动力学和吸附等温线模型.表征结果表明:两种材料基本骨架一致,吸附Sr²⁺对材料骨架影响均可忽略;虽然MIL-100(Fe)-DMA比表面积小于MIL-100(Fe),但由于晶粒尺寸小,堆积形成的介孔结构更有利于Sr²⁺的扩散.吸附实验结果表明:随着反应时间和初始Sr²⁺浓度的增加,两种材料对Sr²⁺的吸附量先迅速增大再逐渐达到平衡;随着pH值的增大,两种材料对Sr²⁺的吸附量增大,且碱性条件下吸附效果好;两种材料吸附过程均符合准二级动力学模型、颗粒内扩散模型和Langmuir吸附等温模型;采用三价铁盐作为铁源以及DMA作为有机溶剂可提高MIL-100(Fe)材料对Sr²⁺的吸附效果.     

Triton X-100对土壤中柴油的解吸特征及影响因素

为考察非离子表面活性剂Triton X-100对土壤中柴油解吸特性及土壤理化性质对其解吸的影响,通过振荡平衡法研究Triton X-100对浙江水稻土、重庆紫壤、江西红壤、海南沙土、青海灰漠土和黑龙江黑土中柴油解吸行为及其影响因素.结果表明,Triton X-100对浙江水稻土、重庆紫壤、江西红壤、海南沙土、青海灰漠土和黑龙江黑土中柴油的解吸均符合先快后慢、最后达到解吸平衡的规律,平衡时解吸量分别1.61、1.85、1.80、2.29、2.01和1.13 mg/g.其解吸动力学过程均符合准二级动力学模型（R2>0.99）;6种典型土壤中柴油的等温解吸特征可较好地用修正的米氏方程模型进行描述（R2>0.92）.Q_max（柴油最大解吸量）介于1.81~2.23 mg/g之间,浙江水稻土、重庆紫壤、江西红壤、海南沙土、青海灰漠土和黑龙江黑土中ρ_max（柴油最大解吸率）分别为73.20%、78.06%、75.63%、90.36%、79.89%和62.92%;土壤各理化性质对Triton X-100解吸土壤中柴油的影响起综合作用,其中土壤w（砂粒）与ρ_max呈显著正相关（R2=0.993 6,P < 0.01）,对Triton X-100解吸柴油的影响最大;而CEC（阳离子交换量）、w（OM）、w（黏粒）均与ρ_max呈显著负相关（P < 0.05）.研究显示,修正的米氏方程可用于描述柴油在土壤-水-表面活性剂Triton X-100系统中的解吸行为,w（砂粒）是影响不同土壤中柴油解吸的关键因子,可为应用Triton X-100修复柴油污染土壤提供理论基础.      

表面活性剂对热带假丝酵母降解苯酚的影响

通过液态发酵培养法探讨了添加2种化学表面活性剂十六烷基三甲基溴化铵(CTAB)、曲拉通X-100(Triton X-100)以及生物表面活性剂二鼠李糖脂(dirhamnolipid,diRL)对1株热带假丝酵母(Candida tropicalis)降解苯酚的影响.结果表明,发酵液中苯酚的分解和菌体生长的不同步,反映了苯酚对该菌的毒性作用以及苯酚降解过程中中间产物的形成.CTAB对热带假丝酵母具有毒性作用,抑制菌体对苯酚的降解.低浓度(0.1、0.3CMC)的Triton X-100对C.tropicalis的生长及对苯酚的降解有一定的促进作用,分别将苯酚降解完全的时间由空白的48h提前至24h和36h;随着Triton X-100浓度增大(1.0、3.0CMC),降解初期菌体的衰亡减缓,但使菌体生长滞后,苯酚分解完全的时间延长.生物表面活性剂diRL促进菌体对苯酚降解的同时显著地促进了C.tropicalis的生长,且促进作用随着加入diRL浓度的增大而增强,1.0、3.0CMC的diRL将苯酚降解完全的时间都提前到24h;而diRL在发酵过程中浓度也逐渐降低,这表明diRL很大程度上减弱了苯酚对菌体的毒性,并且可以共同作为碳源促进菌体的生长.     

选择性吸附法处理含表面活性剂和多环芳烃的土壤淋洗液研究

比较研究了H103树脂、活性炭、沸石、硅藻土和膨润土等5种吸附剂对土壤淋洗液中TX-100与PAHs的吸附性能.批实验结果表明,H103树脂、活性炭、沸石、硅藻土和膨润土吸附后,淋洗液中T-PAHs及TX-100浓度分别为0.03和0 mg·L~(-1)、0.16和3623 mg·L~(-1)、15.21和6175 mg·L~(-1)、15.98和6555 mg·L~(-1)、9.49和4332 mg·L~(-1),选择性吸附系数排序依次为活性炭膨润土沸石硅藻土H103树脂.其中,活性炭能够去除淋洗液中99%的PAHs,同时保留51.33%的TX-100回收再利用,选择吸附系数达到109.5.活性炭固定床实验中,由淋洗液溶质的穿透曲线计算出物质的吸附容量.当空隙体积为2.5-7PV时,活性炭能够去除淋洗液中72%的PAHs,同时保留81%的TX-100,平均选择吸附系数为10.08.由此可见,活性炭固定床可有效处理含表面活性剂土壤淋洗液中的多环芳烃,同时实现表面活性剂的回收再利用.     

利用固定化技术与添加表面活性剂增强双酚A降解率的研究

以SiO_2为载体,戊二醛为交联剂,用以固定游离态漆酶降解双酚A(Bisphenol A,BPA).同时,对比了游离态漆酶与固定化漆酶在不同pH值与温度下的最佳酶活与酶稳定性,再通过添加表面活性剂来增加酶活及BPA去除效果.结果表明,与游离态漆酶相比,固定化漆酶对不同酸碱的适应性与耐热性均有所提高,在pH为2~8时,固定化漆酶的活性均高于游离态漆酶,且最佳活性温度也从游离态漆酶的40℃提高至50℃.在BPA降解率方面,固定化漆酶的降解率皆高于游离态漆酶,反应6 h后,对100 mg·L~(-1)BPA的去除率可分别达到92%与85%.通过添加非离子型表面活性剂Triton X-100,反应4 h后固定化漆酶可完全降解BPA,相对活性为67%;游离态漆酶于6 h将BPA降解完全,相对活性为32%.实验证实Triton X-100可作为酶活诱导剂用以提高漆酶活性及BPA的降解率,降低了处理成本且具有一定的应用前景.     

Growth factors, kinetics and biodegradation mechanism associated with Pseudomonas nitroreducens TX1 grown on octylphenol polyethoxylates

The growth properties and biodegradation mechanism of a Gram-negative bacterium, Pseudomonas nitroreducens TX1 that was able to grow on branched octylphenol polyethoxylates (OPEO(n), average n=9.5) as the sole carbon source over a wide concentration range (1-100,000 mgl(-1)) were studied. Analysis of growth factors indicated the highest specific growth rate (micro) of 0.53 h(-1) was obtained at an initial concentration of 5,000 mgl(-1) OPEO(n). An optimal C/N ratio of 12 was obtained for (NH(4))(2)SO(4) as the nitrogen source in a cultivated medium at pH 7. The kinetic analysis demonstrated that bacterial growth and OPEO(n) degradation followed the Monod equation and were based on a substrate concentration inhibition model and pseudo-first-order reaction, respectively. The substrate inhibition coefficient was over 18,000 mgl(-1) and this indicates that the strain has an ability to sustain growth at high concentrations of OPEO(n) and use it as the sole carbon source under such a stress condition. Furthermore, LC-MS analysis showed that the biodegradation mechanism of dodecyl octaethoxylate (AEO8) by P. nitroreducens TX1 was the sequential cleavage of the ethoxylate chain.