一株苯酚降解菌的分离鉴定及响应面法优化其固定化

从太原市焦化厂废水活性污泥中分离、筛选出一株苯酚降解细菌,经生理生化反应和16S rRNA鉴定,该菌株为Diaphorobacter属细菌,命名为PD-07.代谢机制研究表明,苯酚可诱导该菌合成邻苯二酚2,3-加氧酶降解苯酚.为了提高该菌株对苯酚的降解率,以海藻酸钙为材料,对该菌株进行包埋固定化研究.首先采用Plackett–Burman实验设计筛选出影响固定化菌株苯酚降解率的关键因素,然后采用最陡爬坡实验逼近最大苯酚降解率响应区域.最后用Box–Behnken实验设计及响应面回归分析,应用二次方程对实验数据进行拟合得,拟合曲线与实验实测值相关性良好,最佳条件为海藻酸钠浓度3.83%(m/V)、CaCl20.3mol/L、菌胶比1:26.73、固定化时间2h、摇床转速180r/min、培养温度30℃、初始pH值7.2、液固比4.86:1,在此条件下苯酚降解率可达96.89%.     

乌鲁木齐大气PM2.5对质粒DNA的损伤研究

2012年1月~2012年12月采集乌鲁木齐大气PM2.5样品,使用质粒DNA评价法研究了不同季节PM2.5的氧化能力,并进行氧化性毒性与相应气象因素和质量浓度之间的相关性研究.结果表明,乌鲁木齐大气PM2.5的质量浓度具有冬季最高,春季和秋季次之,夏季最低的季节性变化特征;PM2.5全样和水溶部分氧化能力的季节差异较大,对质粒DNA的氧化性损伤具有冬季最大,春季和夏季之次,秋季最低.冬、春、夏、秋季大气PM2.5全样的TD30(PM2.5对质粒DNA造成破坏达到30%所需要的颗粒物的剂量)平均值分别为440,491,503,515μg/mL,水溶部分分别为474,721,666,600μg/mL.绝大部分PM2.5样品全样的TD30值均小于水溶部分样,表明全样的毒性大于相应的水溶部分样.全样TD30值与平均温度显著(P<0.05)正相关,表明寒冷的天气/季节可能造成PM2.5的高毒性.水溶样TD30值与风速显著(P<0.01)正相关,与相对湿度显著负相关.这表明,高的风速和低的相对湿度可能跟较低和较高的PM2.5的毒性有关.PM2.5氧化性损伤能力的大小与其质量浓度之间的相关性不明显,表明仅以颗粒物的质量浓度来评价大气颗粒物氧化性损伤能力大小的方法并不能真实地反映其对人体健康的危害程度,起决定作用的还是颗粒物的化学组成及其表面吸附的有害成分.     

海岸带表层沉积物中磷的地球化学特征

通过连续提取法对莱州湾主要入海河流及近岸海域表层沉积物中5种形态磷进行了定量分析.结果表明,近海沉积物自生钙结合磷含量(45.6%)高于河流(37.3%),而铁结合磷(Fe-P)含量(18.2%)却低于河流(31.3%).在近海,可交换或弱结合磷含量和粉砂比例呈正相关,表明该形态磷主要吸附于细粒粉砂.河流沉积物Fe-P与Fe浓度呈显著正相关(P0.01),表明河流沉积物Fe-P分布受沉积物活性铁含量的控制.河口处Fe-P普遍低于相应河流,这可能与海相泥沙输入及河口厌氧区硫酸盐还原或硫化物累积有关.近海沉积物总可提取态磷平均浓度总体呈现出由海洋向河口方向递减的趋势.     

响应面法优化厌氧上清液除磷的研究

在用铁盐对厌氧段富磷上清液进行化学磷沉淀以实现磷的回收和达标排放的SBR系统中,为了减少铁盐化学除磷残余物可能对生物处理系统的影响,采用Box-Benhnken中心组合试验原理和响应面分析法,选择Fe:P、混凝搅拌强度、絮凝搅拌强度、搅拌时间等为自变量,残余铁离子为响应值,研究自变量之间的交互作用,以期优化化学除磷条件.通过Design-Expert 8.0软件得到1个二次响应曲面模型.得出最佳除磷条件:Fe:P比为1.40:1,搅拌强度为275r/min,快速搅拌时间为30s,絮凝搅拌强度为60r/min,絮凝时间为18min,沉淀时间为20min.在此条件下,化学混凝后残余铁离子浓度为0.37mg/L,化学除磷率大于97.66%.     

模拟环境条件下δ-MnO_2氧化As(Ⅲ)的搅拌流动动力学特征

采用搅拌流动法研究了酸性水钠锰矿及水羟锰矿2种δ-MnO2矿物氧化As(Ⅲ)的动力学过程,构建了可用于多相体系的搅拌-流动氧化还原反应动力学模型.经过As吸附量的校正后,该模型对酸性水钠锰矿及水羟锰矿氧化As(Ⅲ)动力学数据拟合度分别为0.980和0.951,模型拟合得到pH 7时2种矿物单位比表面上氧化As(Ⅲ)的初始反应速率常数k分别为0.131,0.014min-1·m-2.相比而言,该速率常数明显高于批量法得到的表观速率常数kobs,0.021,0.001min-1?m-2更接近真实的化学动力学参数.搅拌流动法与批量法得到的不同矿物的速率常数大小趋势一致,即尽管酸性水钠锰矿对As(Ⅲ)的氧化率低于水羟锰矿,单位比表面上酸性水钠锰矿氧化As(Ⅲ)初始反应速率却远高于水羟锰矿.反应过程分析表明,反应初始阶段,As(Ⅲ)的吸附为主要限速步骤;而随着反应的进行,矿物表面反应位点逐渐钝化或减少,反应位点数量成为限速步骤.     

Electro-Fenton法处理印染废水应用研究进展

Electro-Fenton法是利用电解的方法产生Fe2+和H2O2,新生的Fe2+和H2O2作用产生·OH。作为一种新兴的废水处理技术,在处理难降解有机废水方面,国内外已开展了广泛的研究,对于处理高浓度难降解有机废水效果良好。阐述了Electro-Fenton法的发展、分类、反应机理及其在印染废水处理中的应用研究现状,并指出Electro-Fenton法存在的主要问题和今后的发展方向。     

生物法处理海上油田含聚生产污水研究报告

应用"倍加清"特种微生物技术,结合"气浮+生化+固液分离"的处理工艺,以中海油绥中SZ36-1陆上终端含聚污水为水质样本,研究生物法处理海上油田含聚生产污水的效果。结果表明,该工艺处理后出水可达"1.5.2"的水质标准,远优于"10.10.3"的注入水质指标要求,并确定了相关技术参数。该技术具备处理效果好、适应来水水质范围大、环境友好等优势。但由于空间重量的限制,尚不适用于海上油田平台的生产水处理工艺。     

电感耦合等离子体原子发射光谱法测定电路板中金属含量的方法改进

根据样品中被测元素的特点,采用硝酸-氢氟酸-高氯酸-硼酸-硝酸和硝酸体系,对电路板中金属元素进行消解,用电感耦合等离子体原子发射光谱法对电路板中的金属元素含量进行定量分析。该方法具有简单、准确的特点,可以快速分析电路板中的金属元素含量。     

Effects of metal and acidic sites on the reaction by-products of butyl acetate oxidation over palladium-based catalysts

Catalytic oxidation is widely used in pollution control technology to remove volatile organic compounds. In this study, Pd/ZSM-5 catalysts with different Pd contents and acidic sites were prepared via the impregnation method. All the catalysts were characterized by means of N2 adsorption- desorption, X-ray fluorescence （XRF）, HE temperature programmed reduction （H2-TPR）, and NH3 temperature programmed desorption （NH3-TPD）. Their catalytic performance was investigated in the oxidation of butyl acetate experiments. The by-products of the reaction were collected in thermal desorption tubes and identified by gas chromatography/mass spectrometry. It was found that the increase of Pd content slightly changed the catalytic activity of butyl acetate oxidation according to the yield of CO2 achieved at 90%, but decreased the cracking by-products, whereas the enhancement of strong acidity over Pd-based catalysts enriched the by-product species. The butyl acetate oxidation process involves a series of reaction steps including protolysis, dehydrogenation, dehydration, cracking, and isomerization. Generally, butyl acetate was cracked to acetic acid and 2- methylpropene and the latter was an intermediate of the other by-products, and the oxidation routes of typical by-products were proposed. Trace amounts of 3-methylpentane, hexane, 2-methylpentane, pentane, and 2-methylbutane originated from iso4merization and protolysis reactions.     

Ultrasonic preparation of nano-nickel/activated carbon composite using spent electroless nickel plating bath and application in degradation of 2,6-dichlorophenol

Ni was effectively recovered from spent electroless nickel （EN） plating baths by forming a nano-nickel coated activated carbon composite. With the aid of ultrasonication, melamine- formaldehyde-tetraoxalyl-ethylenediamine chelating resins were grafted on activated carbon （MFT/AG）. PdC12 sol was adsorbed on MFT/AC, which was then immersed in spent electroless nickel plating bath; then nano-nickel could be reduced by ascorbic acid to form a nano-nickel coating on the activated carbon composite （Ni/AC） in situ. The materials present were carefully examined by Fourier transform infrared spectroscopy, X-ray diffraction, field emission scanning electron microscopy, X-ray photoelectron spectroscopy and electro- chemistry techniques. The resins were well distributed on the inside and outside surfaces of activated carbon with a size of 120 ± 30 nm in MFT/AC, and a great deal of nano-nickel particles were evenly deposited with a size of 3.8 ± 1.1 nm in Ni/MFT. Moreover, Ni/AC was successfully used as a catalyst for ultrasonic degradation of 2.6-dichloronhenol.