高压脉冲电凝聚技术处理活性染料废水试验研究

难生物降解有机废水是废水处理的难点。阐述了高压脉冲电凝聚技术处理高浓度、难生物降解有机废水的最新机理。采用高压脉冲电凝聚技术处理活性染料（活性红）生产废水．研究了影响高压脉冲电凝聚技术处理活性染料废水效果的操作条件及影响因素．结果表明，在最佳处理工艺条件下。CODCr浓度12628mg／L的生产废水经处理后CODCr去除率为65％左右。再经后续混凝沉淀，最终出水CODCr可降低到1000mg／L以下。     

不同pH条件下Fe~(2+)/Fe~(3+)/Ni~(2+)/O_3体系对活性艳蓝X-BR的催化氧化

臭氧和催化臭氧氧化法是对印染废水有效的处理手段之一。选取用途较广的活性艳蓝X-BR为研究对象,探讨了氧化过程中染料的降解和结构变化情况。并选取了Fe2+、Fe3+和Ni2+为均相催化剂,讨论了pH对催化效果的影响。实验表明,均相催化体系中,酸性条件下更有利。     

铁阳极电凝聚处理活性黑KN-B染料废水

对铁阳极电凝聚处理活性黑KN-B染料废水过程进行了实验研究.考察了电流密度、染料溶液初始pH值、电介质浓度及种类、温度、染料浓度等因素对脱色效率的影响.结果表明,在一定实验条件下,活性黑KN-B模拟废水的脱色效率达93%;电流强度、染料浓度、电解液初始pH值及电解质的种类对染料溶液脱色效率影响显著,电解液温度、电解质的浓度对脱色效率的影响不明显;以铁为阳极的原位电凝聚处理活性黑KN-B模拟废水混凝过程中主要作用机理以吸附电性中和为主;电凝聚过程中活性黑KN-B在阴极上发生了还原反应.     

活性艳橙K-7R分子印迹聚合物微球的制备及结合特性研究

以微米级聚苯乙烯微球为种球,活性艳橙K-7R为模板分子,甲基丙烯酸为功能单体,乙二醇二甲基丙烯酸酯为交联剂,采用单步溶胀聚合法在水相中制得了分子印迹聚合物微球(MIPs),并用平衡吸附实验研究了其吸附性能。通过Scatchard分析,结果表明,MIPs在识别K-7R过程中存在两类结合位点,高亲和力结合位点的平衡离解常数Kd1=14.855μmol/L,最大结合量Qmax1=1.282μmol/g;低亲和力结合位点的平衡离解常数Kd2=70.939μmol/L,最大结合量Qmax2=3.930μmol/g。该MIPs对K-7R有较高的亲和性和选择性。     

Comparison of four supports for adsorption of reactive dyes by immobilized beads

Four materials, sodium carboxymethylcellulose （Na-CMC）, sodium alginate （SA）, polyvinyl alcohol （PVA）, and chitosan （CTS）, were prepared as supports for entrapping fungus Aspergillusfumigatus. The adsorption of synthetic dyes, Reactive Brilliant Blue KN- R, and Reactive Brilliant Red K-2BP, by these immobilized gel beads and plain gel beads was evaluated. The adsorption efficiencies of Reactive Brilliant Red K-2BP and Reactive Brilliant Blue KN-R by CTS immobilized beads were 89.1% and 93.5% in 12 h, respectively. The adsorption efficiency by Na-CMC immobilized beads was slightly lower than that of mycelial pellets. But the dye culture mediums were almost completely decolorized in 48 h using the above-mentioned two immobilized beads （exceeding 95%）. The adsorption efficiency by SA immobilized beads exceeded 92% in 48 h. PVA-SA immobilized beads showed the lowest adsorption efficiency, which was 79.8% for Reactive Brilliant Red K-2BP and 92.5% for Reactive Brilliant Blue KN-R in 48 h. Comparing the adsorption efficiency by plain gel beads, Na-CMC plain gel beads ranked next to CTS ones. SA and PVA-SA plain gel beads hardly had the ability of adsorbing dyes. Subsequently, the growth of mycelia in Na-CMC and SA immobilized beads were evaluated. The biomass increased continuously in 72 h. The adsorption capacity of Reactive Brilliant Red K-2BP and Reactive Brilliant Blue KN-R by Na-CMC immobilized beads was 78.0 and 86.7 mg/g, respectively. The SEM micrographs show that the surface structure of Na-CMC immobilized bead is loose and finely porous, which facilitates diffusion of the dyes.     

活性染料染色模拟液的电化学混凝研究

本文以铁电极电解装置处理活性翠篮K-GL及活性红M-8B染料染色模拟液,研究了电流密度,溶液pH值同模拟液脱色率及COD去除率的关系,同时还考察了PVA对于模拟液脱色及去除COD的影响。     

复极性固定床电解反应器对活性染料的降解

本文用复极性固定床电解反应器对１６种活性染料的脱色降解进行了试验研究。结果表明：染料脱色率在９９．６％以上,出水上清液ＣＯＤ去除率绝大部分在９０％以上,对活性翠蓝ＫＮ－Ｇ和活性深蓝ＫＭ－ＧＲ的铜去除率分别为９７．０％和９９．７％。     

活性炭纤维对活性染料的吸附动力学研究

研究了活性炭纤维从水溶液中吸附4种活性染料（活性艳红K-2BP、活性翠蓝KN-G、活性金黄K-3RP、活性黑KN-B）的吸附特性,从动力学角度探讨了吸附机理.结果表明,活性炭纤维对4种染料的平衡吸附量q_e均随着初始浓度和温度的增加而升高,相同条件下,q_e的大小顺序为：活性艳红＞活性金黄＞活性黑＞活性翠蓝.吸附过程符合伪二级吸附速率方程,染料分子的空间结构、大小和极性是影响初始吸附速率的主要因素.活性炭纤维对4种染料的吸附活化能都比较低,依次为16 .42、3 .56、5 .21和26 .38 kJ·mol^-1,说明吸附过程以物理吸附为主.     

印染废水的混凝脱色研究

针对以使用活性染料为主的印染厂的生产废水,选择六种常用的无机混凝剂以及自行研制的脱色剂,进行混凝实验,在确定各自最佳pH、最佳投药量的情况下,比较了COD、色度的去除率,絮体平均沉降速率,产生污泥的体积,污泥密度,以选择最佳效果的药剂品种和混凝条件。结果表明:脱色剂具有高效脱除色度和去除COD的特性,单独使用时,在pH为7.5,投加量为200mg/L的最佳条件下,色度去除率达到95.7%,COD去除率达到54.1%,产生的污泥量很少,与聚合氯化铝配合使用可以提高沉降速率。