2 000 m超深水水下分离器泄漏油气扩散特性研究

深水水下分离器服役过程中由于腐蚀、地质灾害和环境高压作用,存在失效泄漏风险。针对2 000 m超深水水下分离器可能存在的失效泄漏问题,基于计算流体动力学CFD方法,建立分离器失效泄漏后果数值仿真分析模型,对分离器泄漏场景进行模拟与分析,研究2 000 m水深条件下分离器泄漏油气扩散规律,并考虑不同泄漏位置对油气扩散行为的影响。结果表明:水下分离器泄漏包括压力扩散和自由扩散两个阶段,压力扩散阶段历时极短,自由扩散阶段耗时较长;泄漏口位置对泄漏结果有较为明显的影响,分离器上部泄漏,油气全部溢出,分离器中下部泄漏,大部分油气保留于分离器内部,最终形成分明的油气水界面;分离器内部压力随时间迅速上升,t=0.25 s左右接近于20 MPa,后期在20 MPa左右呈极微小波动,泄漏速率随分离器内部压力增大迅速减小,达到最低点之后,呈微小波动状变化。     

可变径管道漏磁检测有限元仿真与实验研究

为了更好地支持压力管道检验,降低事故率,本文基于漏磁检测原理,利用有限元分析软件建立了管道外漏磁检测模型,对管道漏磁检测进行了仿真计算,得到了缺陷处漏磁场特征曲线,模拟了圆柱形缺陷对管道外壁漏磁场的影响,得出了不同参数缺陷对漏磁场的影响规律,并且基于理论和有限元计算结果试制了可变径管道外漏磁检测仪的样机,利用该检测仪对壁厚为8mm的带有人工缺陷的管道进行扫描检测,研究不同参数缺陷对漏磁场信号的影响规律。结果表明,所得结果与有限元仿真的结果吻合良好,且缺陷检测精度及效果满足要求,另外,检测装置对内外壁缺陷检测同样可行有效,适合特种设备（压力管道）检测的工程应用。     

混合药物粉尘输运过程静电特性实验研

兽药制药粉尘加工工艺过程中,由于粉尘颗粒之间或颗粒与设备、管壁之间的碰撞、摩擦,导致装置内部静电荷量积聚,激发静电放电,粉尘燃烧或爆炸的事故频发。实验主要通过包括粉尘与管材摩擦的漏电电流测试和静电放电火花对粉尘云点燃敏感性测试两部分。结果表明:单一药物药粉的静电漏电电流随着管材管径的增大,管长的增长,静电漏电电流逐渐变大;随着倾斜角的增大,静电漏电电流先增大后降低;镀锌铁管的漏电电流大于PVC管,电荷逸散速度更快。单一兽药粉的粉尘云放电火花最小点燃能量随质量浓度的变化,呈现二次曲线的变化趋势。混合兽药粉与单一兽药粉的漏电电流和粉尘云放电火花最小点燃能量的测试结果的变化趋势是一致的。     

泄漏孔形状对液化石油气泄漏扩散的影响

基于液化石油气的特点,建立了有限空间内部发生泄漏扩散的物理模型,模拟了液化石油气泄漏扩散的过程,通过模拟结果分析其扩散规律,并对比当泄漏孔形状分别为正方形、圆形、三角形时液化石油气扩散过程的变化以及对所形成的的爆炸危险区域的影响。监测点1（0.8,0.3,0）,点2（2.4,0.3,2.5）,点3（0,0.3,1.5）,点4（2,0.3,3）的浓度变化,找出报警器的最佳安放位置。结果表明:泄漏时间相同,丙烷的扩散范围从大到小依次为三角形孔口、圆形孔口、正方形孔口,爆炸危险区域也与泄漏孔形状有关,三角形孔口的危险区域范围最广,其次是圆形泄漏孔,正方形泄漏孔的范围最小,点1处的丙烷浓度增长幅度较大,浓度较高,可以更早达到报警浓度。     

常规净水工艺对猛水蚤的去除机理及效果

为实现对桡足类生物泄露风险的高效控制,以猛水蚤为研究对象,开展了常规净水工艺对桡足类生物的去除作用机理及效果研究,重点研究了猛水蚤去除与絮体颗粒形态特性关系和在石英砂滤床的分布规律.结果表明:优化操作条件下,混凝沉淀和过滤对猛水蚤去除率均可达99%,最佳工况包括快速搅拌300 r/min(1min)、中速搅拌150 r/min(5min)和低速搅拌75 r/min(5min),聚合氯化铝(PAC)投加量10 mg/L,沉淀时间0.5h,滤速9m/h,过滤周期1d.混凝对猛水蚤的去除效率主要决定于猛水蚤与絮体的有效吸附,絮体颗粒粒径越大、分形维数越低,猛水蚤去除率越高;过滤水冲刷携带引起的被动迁移,是导致猛水蚤穿透砂滤池的主要原因,适当降低滤速和缩短过滤周期,控制猛水蚤被动迁移规模,可以达到提高猛水蚤去除率效果.     

Optimal timing of carbon capture policies under learning-by-doing

Using a standard Hotelling model of resource exploitation, we determine the optimal energy consumption paths from three options: dirty coal, which is non-renewable and carbon-emitting; clean coal, which is also non-renewable but carbon-free thanks to carbon capture and storage (CCS); and solar energy, which is renewable and carbon-free. We assume that the atmospheric carbon stock cannot exceed an exogenously given ceiling. Taking into account learning-by-doing in CCS technology, we show the following results: (i) clean coal exploitation cannot begin before the outset of the carbon constrained phase and must stop strictly before the end of this phase; (ii) the energy price path can evolve non-monotonically over time; and (iii) when the solar cost is low enough, an unusual energy consumption sequence along with solar energy is interrupted for some time and replacement by clean coal may exist.     

Wastewater-nitrogen removal using polylactic acid/starch as carbon source: Optimization of operating parameters using response surface methodology

The use of PLA/starch blends for nitrogen removal was achieved. The influence of different operating parameters on responses was verified using RSM. The conditions for desired responses were successfully optimized simultaneously. Blends material may have a promising application prospect in the future. Nitrogen removal from ammonium-containing wastewater was conducted using polylactic acid (PLA)/starch blends as carbon source and carrier for functional bacteria. The exclusive and interactive influences of operating parameters (i.e., temperature, pH, stirring rate, and PLA-to-starch ratio (PLA proportion)) on nitrification (Y₁), denitrification (Y₂), and COD release rates (Y₃) were investigated through response surface methodology. Experimental results indicated that nitrogen removal could be successfully achieved in the PLA/starch blends through simultaneous nitrification and denitrification. The carbon release rate of the blends was controllable. The sensitivity of Y₁, Y₂, and Y₃ to different operating parameters also differed. The sequence for each response was as follows: for Y₁, pH>stirring rate>PLA proportion>temperature; for Y₂, pH>PLA proportion>temperature>stirring rate; and for Y₃, stirring rate>pH>PLA proportion>temperature. In this study, the following optimum conditions were observed: temperature, 32.0°C; pH 7.7; stirring rate, 200.0 r·min^-1; and PLA proportion, 0.4. Under these conditions, Y₁, Y₂, and Y₃ were 134.0 μg-N·g-blend^-1·h^-1, 160.9 μg-N·g-blend^-1·h^-1, and 7.6 × 10³ μg-O·g-blend^-1·h^-1, respectively. These results suggested that the PLA/starch blends may be an ideal packing material for nitrogen removal.     

基于能位测定和示踪检测法的地下煤火漏风状态研究

应用能位测定法和示踪检测技术联合检测了鸡西老二井火区地下漏风状态。通过测试计算相对总压值得出了火区范围内井巷系统与采空区的风流关系,进而定性确定了火区内老二井与胜利井之间存在的可能漏风路径。在此基础上,利用瞬时释放示踪气体法确定了胜利井和老二井间的漏风方向和漏风速度,计算得出了火区下采空区内平均直线漏风风速为0.13m/s,漏风量为776m3/min。研究结果为矿区采取针对性的防灭火措施提供依据,并为同类问题的解决提供参考。     

生物炭对土壤水肥热效应的影响试验研究

本文通过野外大田小区试验以番茄（Lycopersicon esculentum Mill）为供试作物,通过在土壤中施加不同含量生物炭（Biochar）研究生物炭对土壤含水率、有机碳、速效养分含量和土壤温度的影响,从而寻求一个较为合适的施用量,为生物炭在内蒙古地区的大面积推广提供科学的理论依据。试验共设5个处理,3个重复：不施加生物炭（CK）,生物炭使用量分别为10 t·hm^-2（A）,20 t·hm^-2（B）,40 t·hm^-2（C）,60 t·hm^-2（D）,在各生育期取土样测定土壤含水率、有机碳、速效养分含量,并在各生育期连续3天测定土壤地表温度。试验结果表明：不同处理下土壤含水率随生物炭施用量增加呈先增加后减小的趋势,且均高于对照组,其中施炭量为40 t·hm^-2处理的土壤含水率增幅最明显,0～10 cm土层各生育期土壤含水率较对照组最大增幅分别为20.8%、13.7%、21.8%,10～20 cm土层各生育期土壤含水率较对照组最大增幅分别为33.9%、17.1%、21.3%;不同处理下土壤温度随着生物炭施用量的增加而升高,两者具有显著的正相关关系,各生育期各处理土壤地表温度较对照组最大增幅分别为58.1%、31.3%、55.8%;不同处理土壤有机碳含量随着生物炭施用量的增加而增大,番茄各生育期各处理土壤有机碳含量较对照组最大增幅分别为80.9%、62.7%、63.9%;不同处理土壤中碱解氮、速效钾、速效磷含量均随生物炭施用量的增加而呈现先增大后减小的趋势,且均大于对照组,各生育期各处理土壤碱解氮较对照组最大增幅分别为92.7%、45.7%、106.5%,速效磷最大增幅分别为120.1%、39.3%、250.4%,速效钾最大增幅分别为86.2%、118.5%、203.4%。综上所述,生物炭对于砂壤土具有保水、保肥、保温的特性,对于提高土壤水肥利用效率,增加土壤有机碳具有重要的作用,而且通过试验验证40 t·hm^-2的施?     

Carbon abatement in the fuel market with biofuels: Implications for second best policies

A carbon tax on fuel would penalize carbon intensive fuels like gasoline and shift fuel consumption to less carbon intensive alternatives like biofuels. Since biofuel production competes for land with agricultural production, a carbon tax could increase land rents and raise food prices. This paper analyzes the welfare effect of a carbon tax on fuel consisting of gasoline and biofuel in the presence of a labor tax, with and without a biofuel subsidy. The market impacts of a carbon tax are also compared with that of a subsidy. Findings show that if a carbon tax increases biofuel demand, the tax interaction effect due to higher fuel prices is exacerbated by higher land rent and food prices and greater erosion of the carbon tax base. Thus, the second best optimal carbon tax for fuel is lower with biofuel in the fuel mix, especially if biofuel is subsidized.