Direct individual analysis using Scanning Electron Microscopy combined with online observation was conducted to examine the S-rich particles in PM2.5 of two typical polluted haze episodes in summer and winter from 2014 to 2015 in Beijing. Four major types of S-rich particles, including secondary CaSO4 particles (mainly observed in summer), S-rich mineral particles (SRM), S-rich water droplets (SRW) and (C, O, S)-rich particles (COS) were identified.We found the different typical morphologies and element distributions of S-rich particles and considered that (C, O, S)-rich particles had two major mixing states in different seasons. On the basis of the S-rich particles’ relative abundances, S concentrations and their relationships with PM2.5 as well as the seasonal comparison, we revealed that the S-participated formation degrees of SRM and SRW would enhance with increasing PM2.5 concentration. Moreover, C-rich matter and sulfate had seasonally different but significant impacts on the formation of COS.
Nanoscale iron particles (nZVI) is one of the most important engineered nanomaterials applied to environmental pollution control and abatement. Although a multitude of synthesis approaches have been proposed, a facile method to screen the reactivity of candidate nZVI materials produced using different methods or under varying synthesis conditions has yet been established. In this study, four reaction parameters were adjusted in the preparation of borohydride-reduced nZVI. The reductive properties of the resultant nanoparticles were assayed independently using two model aqueous contaminants, Cu(II) and nitrate. The results confirm that the reductive reactivity of nZVI is most sensitive to the initial concentration of iron precursor, borohydride feed rate, and the loading ratio of borohydride to ferric ion during particle synthesis. Solution mixing speed, in contrast, carries a relative small weight on the reactivity of nZVI. The two probing reactions (i.e., Cu(II) and nitrate reduction) are able to generate consistent and quantitative inference about the mass-normalized surface activity of nZVI. However, the nitrate assay is valid in dilute aqueous solutions only (50 mg·L−1 or lower) due to accelerated deactivation of iron surface at elevated nitrate concentrations. Additional insights including the structural and chemical makeup of nZVI can be garnered from Cu(II) reduction assessments. The reactivity assays investigated in this study can facilitate screening of candidate materials or optimization of nZVI production parameters, which complement some of the more sophisticated but less chemically specific material characterization methods used in the nZVI research. 相似文献
Aiming to investigate the impacts of n-octanol addition on the oxidation reactivity, morphology and graphitization of diesel exhaust particles, soot samples were collected from a four-cylinder turbocharged diesel engine fueled with D100(neat diesel fuel), DO15(85% diesel and 15% n-octanol, V/V) and DO30(70% diesel and 30% n-octanol, V/V). All tests were conducted at two engine speeds of 1370 and 2150 r/min under a fixed torque of 125 N ·m. The soot properties were characterized by thermogravimet... 相似文献
Abstract Sewage sludge from four publicly-owned treatment works was sampled and characterized in terms of parameters affecting transport at the 106-mile deep ocean disposal site as part of the US Environmental Protection Agency's site monitoring programme. Samples from treatment plants in Passaic Valley, Rahway, and Elizabeth, New Jersey and New York City were characterized in terms of dynamic size distribution, suspended solids and density. the transport characteristics of sludge particles were measured using a 2 metre computer-interfaced laboratory settling column. Experiments were conducted at constant salinity (35 ppt) while varying hydrodynamic mixing, sludge type and concentration using a modified factorial experimental design. Hydrodynamic power dissipation was varied so that the vertical dispersion and rms fluid shear rate ranged between 0-6 cm2S?1 and 0-30s?1 respectively. Results indicate that at least 80% of suspended sludge particles will eventually settle under mixed conditions. the average settling velocities ranged between 0.05-4.05 × 10-3 cm s-1. Shear rates above 15 s?1 inhibited sludge settling due to aggregate breakup and boundary effects, but at a lower shear rate, differential settling and fluid shear were the dominant transport mechanisms. Sludge dilution (1/500-1/5000) had a limited effect on the settling rate. Results from this study can be used to calibrate particle transport models to determine the fate of sludge disposed at an ocean disposal site. 相似文献
Since the living microorganisms in activated sludge continuously change, it is difficult to conduct controlled experiments and achieve reproducible results for evaluating sludge characteristics. Synthetic sludge, as a chemical surrogate to activated sludge, could be used to investigate the sludge physicochemical properties, and it is desirable to prepare synthetic sludge with similar structure and properties to real activated sludge to explore the flocculation and settlement processes in activated sludge systems. In this work, a high-strength synthetic sludge was prepared with functional polystyrene latex particles as the framework and extracellular polymeric substances (EPS) to modify its surface. The flocculation and settling characteristics of the microspheres and the prepared synthetic sludge were tested. Compared with other three functional polystyrene latex microspheres, the synthetic sludge prepared with EPS-modified polystyrene latex microspheres showed good settling characteristics and a significantly higher strength. They could be used for studying the physicochemical properties of activated sludge. 相似文献