Warm forming die design,Part II: Parting surface temperature response characterization of a novel thermal finite element modeling code

The majority of the research activities in the area of warm forming are concentrated on demonstrating or simulating the improved formability associated with forming lightweight materials such as aluminum alloys at elevated temperatures. However, the ability to design the proper thermal management system within the forming tool is a critical aspect to delivering this technology as a viable, stable production alternative to traditional stamping. This work begins to address the thermal stability issues of this process by examining the impact of process cycle time on the parting surface temperature response. Cycle times of 10, 15, 30, and 300 s were evaluated using a reciprocating surface and a self-heated experimental block of 1020 steel fitted with resistance cartridge heaters. The presented results indicate that cycle time does not significantly impact the steady-state temperature response at the parting surface for a well-insulated die that has proper thermal management. Parting surface experimental results were compared to values obtained numerically and through the use of the novel thermal finite element analysis software PASSAGE/Forming^®.     

Low cost measurements of nitrogen and sulphur dry deposition velocities at a semi-alpine site: gradient measurements and a comparison with deposition model estimates

The conditional time averaged gradient method was used to measure air-surface exchange of nitrogen and sulphur compounds at a semi-alpine site in Southern Norway. Dry deposition velocities were then obtained from the bi-weekly concentration gradient measurements. Annual deposition velocities were found to be 1.4, 11.8 and 4.0 mm s(-1) for NH3, HNO3 and SO2, respectively, if all data were included, and to be 10.8, 11.8 and 13.0 mm s(-1), respectively, if only positive values were included. Measured deposition velocities were compared to two sets of values estimated from a big-leaf dry deposition module applying to two different land types (short grass and forbs, and tundra), driven by measured micrometeorological parameters. The deposition module gives reasonable values for this site throughout the year, but does not reproduce the large variability as shown in the measured data. No apparent seasonal variations were found from either measurements or module estimates due to the very low productivity of the studied area.     

水质总氮测定中的有关问题探讨

对总氮测定中的一系列影响因素,诸如实验用水,器皿的洗涤,实验室环境试剂的提纯、配制和保存,消解温度、压力和时间的控制,以及高氨氮水样中的总氮测定、总氮、总磷的同时测定和其他有关的问题,作了较为详细的探讨,并提出了相应的解决办法。     

智能家电的低待机功耗研究

从智能家电待机工作状态入手,分析电器产品中参与待机工作的各部分电路原理,提出降低潜在功耗设计思路和计算方法,从家电设计研发阶段对待机功耗进行控制,同时对待机功耗精确测量方法关键点进行解读以控制低功耗测试不确定度,有助于低待机功耗设计和测量的标准化和规范化。     

Distribution and transport characteristics of fine particulate matter in beijing with mobile lidar measurements from 2015 to 2018

Accurately quantifying the concentration and transport flux of atmospheric fine particulate matter(PM_2.5) is vital when attempting to thoroughly identify the pollution formation mechanism.In this study,the mobile lidar measurements in Beijing on heavily polluted days in December from 2015 to 2018 are presented.The lidar was mounted on a vehicle,which could perform measurements along designated routes.On the basis of mobile lidar measurements along closed circuits of the 6 th Ring Road...     

街道峡谷内汽车排放污染物浓度分布的观测与数值模拟

在上海某典型街道峡谷内按一定的空间布点,在一定时段内同时对各布点进行采样并做一氧化碳浓度分析,同时记录车辆种类、车流量、气象条件等,分析街道峡谷内污染物浓度的分布.运用风向频率加权(WDFW)方法,结合大气流动和污染物扩散的CFD模型进行数值模拟计算.结果表明,数值模拟结果和现场观测结果较吻合,建筑物低的一侧污染物浓度远高于建筑物高的一侧污染物浓度,两侧的污染物浓度随着高度的增加而降低.     

卫星光学反射膜光谱反射率空间综合环境退化研究

对玻璃基底和金属基底的铝反射膜在紫外、低能电子、低能质子的综合环境作用下的光谱反射率退化进行了实验研究。试验结果表明两种铝反射膜的光谱反射率均发生了退化,且光谱反射率的退化主要集中在可见光波段,在近红外波段退化很小;玻璃基底铝反射膜退化在420 nm左右出现峰值点,2种金属基底铝反射膜的退化的峰值点在450 nm左右。由于电荷沉积在玻璃中后会抑制带电粒子入射,因此玻璃基底铝反射膜的退化要小于金属基底铝反射膜。     

时间因素对钻屑瓦斯解吸指标K1值测定的影响分析

针对时间因素对钻屑瓦斯解吸指标K1测定结果的影响,采用恒温瓦斯放散试验深入分析钻屑瓦斯解吸指标K1测定理论的准确性,总结因时间因素导致K1值测定误差所带来的现场问题。研究结果表明:K1值的测定误差与时间关系密切,测定启动时间越晚,误差越大;测定启动时间由第1 min延后至第2 min,绝对误差和相对误差最大值分别增加0.081 cm3/(g·min1/2)和2.20%;高瓦斯压力条件矿井或煤层的局部高瓦斯压力区域、构造煤发育区的钻屑瓦斯解吸指标K1值测定结果偏低,测定误差偏大。研究结果可为煤与瓦斯突出预测水平的提升提供技术支撑。     

Point Sampling Digital Imagery with ‘Samplepoint’

Measuring percent occurrence of objects from digital images can save time and expense relative to conventional field measurements. However, the accuracy of image analysis had, until now, not reached the level of the best conventional field measurements. Additionally, most image-analysis software programs require advanced user training to successfully analyze images. Here we present a new software program, ‘SamplePoint,’ that provides the user a single-pixel sample point and the ability to view and identify the pixel context. We found SamplePoint to allow accuracy comparable with the most accurate field-methods for ground-cover measurements. Expert use of the program requires minimal training and its ease of use allows rapid measurements from image data. We recommend SamplePoint for calibrating the threshold-detection level of image-analysis software or for making direct measurements of percent occurrence from digital images.     

Monitoring Biofilm Thickness Using A Non-Destructive, On-Line, Electrical Capacitance Technique

Abstact The present study was designed to evaluate indirect, non-invasive, on-line measurement of biofilm thickness using an electrical capacitance technique. Several assays were carried out and the results showed that, at a frequency of 1 kHz, electrical capacitance could be used to measure biofilm thickness indirectly (with a correlation coefficient of 0.9495). The reproducibility revealed by the assays was also highly satisfactory.However, in contrast to what was expected, there was an inverse relationship between electrical capacitance and biofilm thickness, i.e. electrical capacitance diminished with the increase in the biofilm thickness.The tests were also carried out at different frequencies (1 kHz, 10 kHz and 100 kHz)