环渤海湿地芦苇对TC、TN、TP吸收通量的研究

主要调查研究环渤海湿地芦苇对TC、TN、TP的吸收通量。调查表明,2008年环渤海湿地的芦苇面积为20.08×104hm2。2009年,芦苇总生物量在7月、10月和11月的调查结果分别为267.2×104t、183.4×104t和138.0×104t。7月、10月和11月,芦苇对TC的吸收通量分别为115.58×104t、80.68×104t、64.23×104t;对TN的吸收通量分别为4.03×104t、1.45×104t、0.84×104t;对TP的吸收通量分别为0.37×104t、0.10×104t、0.031×104t。     

亚热带稻田生态系统CO2通量的季节变化特征

为估算和评价稻田生态系统碳源/汇强度及其对大气CO₂浓度变化的贡献,研究了稻田生态系统与大气间CO₂交换通量的季节变化特征及其影响因素.采用涡度相关技术对我国亚热带稻田生态系统CO₂交换通量进行了连续监测,在数据剔除、校正和差补的基础上,对瞬时CO₂通量值进行计算求得日CO₂通量值和年CO₂通量值,并对CO₂通量季节变化及其与主要气象因子的关系进行了探讨.结果表明,稻田生态系统光合吸收CO₂通量（GPP）、呼吸排放CO₂通量（R_eco）和净吸收CO₂通量（NEE）的季节变化均呈6～9月较高,1～5月和10～12月较低的对称分布.其中5～9月水稻生长时期的NEE总量占年总量的80%以上,对年NEE总量起决定性作用.光合有效辐射（PAR）和日平均气温（T_a）是GPP与NEE季节变化的最主要影响因子,二者与GPP和NEE分别存在显著的二元线性关系.年净吸收CO₂总量为2?475.6 g/(m²·a),这表明我国亚热带稻田生态系统是大气CO₂的汇.     

基于水资源合理配置的河流“双总量”控制研究——以河北省唐山市为例

河道的最小控制流量和最大纳污控制量（简称“双总量”）是维系河流健康的决定性因子。论文初步建立了基于水资源合理配置的河流“双总量”控制研究技术框架,并对唐山市月尺度的“双总量”控制指标进行核算。通过水资源合理配置,除个别枯水年份和连续枯水年份外,唐山市河道的最小控制流量均可得到满足。在基准年、2010年和2020年3个规划水平年,唐山市规划河流COD的最大纳污控制量分别为16357．57、12659．19和11572．50t／a;NH3-N的最大纳污控制量分别为907．80、660．27和580．09t／a。在统一水资源配置平台上制定的“双总量”控制指标,从根本上保障了竞争用水条件下河流生态需水,客观确立了规划水平年河道纳污能力的年内分配,并整体上提高了河流的最大纳污能力。     

Minimizing leakage from a smelter off-gas system by enhanced control

The off-gas handling system is a vital component of a smelter and it is essential that it operates in accordance with environmental regulations. A key feature of the off-gas management system is maintaining a slightly negative system pressure to prevent gas leakage, such as SO₂, out into the work and external environments. To enhance sustainable development, there is also growing interest in capturing and reusing the significant amount of heat and CO₂ contained within off-gas. The potential incorporation of heat and CO₂ recovery systems places importance on enhancing control to minimize the risk of both gas leakage and disturbance of the smelting process. With these requirements in mind, an easily implementable feedforward control enhancement to existing control schemes is proposed to help provide improved performance.     

Environmental and economic assessment of a greenhouse waste heat exchange

As the economic costs of energy and the negative externalities associated with the combustion of fossil fuels threaten the economic viability of greenhouses in northern climates there is a renewed interest in the use of waste heat. This paper presents a technical and economic methodology to determine the viability of establishing waste heat greenhouses using the waste heat from industrial processes in northern climates. A case study is presented of an exchange between a tomato greenhouse and a flat glass manufacturing plant, which found the waste heat system is significantly more economic to operate than a purely natural gas system.     

Carbonyl sulfide and dimethyl sulfide fluxes in an urban lawn and adjacent bare soil in Guangzhou, China

Carbonyl sulfide (COS) and dimethyl sulfide (DMS) fluxes from an urban Cynodon dactylon lawn and adjacent bare soil were measured during April–July 2005 in Guangzhou, China. Both the lawn and bare soil acted as sinks for COS and sources for DMS. The mean fluxes of COS and DMS in the lawn (–19.27 and 18.16 pmol/(m2 sec), respectively) were significantly higher than those in the bare soil (–9.89 and 9.35 pmol/(m2 sec), respectively). Fluxes of COS and DMS in mowed lawn were also higher than those in bare soils. Both COS and DMS fluxes showed diurnal variation with detectable but much lower values in the nighttime than in the daytime. COS fluxes were related significantly to temperature and the optimal temperature for COS uptake was 29°C. While positive linear correlations were found between DMS fluxes and temperature. COS fluxes increased linearly with ambient COS mixing ratios, and had a compensation point of 336 ppt.     

动力与热力抬升对烟气抬升高度的影响分析

通过模式选择和计算,得出烟气抬升高度的增加与动能和热能的关系,表明当烟囱出口处风速分别为3 m/s、2 m/s和1 m/s时欲增加同样大小的烟气抬升高度,需要的动能比热能要高,结论认为烟气的热力提升比动力提升的贡献大。     

Microstructure of 2205 duplex stainless steel joint in submerged arc welding by post weld heat treatment

The 2205 duplex stainless steel (DSS) is of both good properties austenitic steel and ferritic steel, which applies to the shipbuilding industry usually. In this paper, the OM, XRD and microhardness test methods are used to analyze the variation of submerged arc welded (SAW) joints with and without post weld heat treatment (PWHT). The research results show that the σ phase disappear in the fusion edge zone near heat affect zone (HAZ) and an increase in the welded center zone during the follow-up PWHT, while the amount of γ phase is decreased in the welded center zone with PWHT. A segregation distribution of some second phases is also found in the welded center zone after PWHT. There have two pick values of microhardness arise in the fusion edge zone and the welded center zone separately without PWHT. However, a maximum value of microhardness at the fusion edge zone near HAZ is disappeared and the other is still held at the welded center zone during PWHT. It can be attributed to the changes of second phases, element diffusions and particle segregation during PWHT. A developing mechanism is issued to demonstrate the second phases transferring of the 2205 DSS SAW joints by PWHT.     

Improvement of welding heat source models for TIG-MIG hybrid welding process

Tungsten inert gas-metal inert gas (TIG-MIG) hybrid welding process is an effective way to improve welding productivity and quality due to advantages of the two processes. Mathematical analysis is crucial to fundamentally understand this synergetic welding process. In this study, based on experimental visualization of arc behaviors, some assumptions are proposed to deduce adaptive plane and volumetric heat source models separately for each involved welding method first. The influence of torch angles on distribution of temperature and geometry of weld bead are calculated and compared with experimental results. It shows that this developed algorithm of heat source can be employed to accurately predict welding process whether the electrode gun is slanted backward or forward to the direction of welding. Then TIG-MIG hybrid welding process is simulated and analyzed without considering the attractive or repulsive force of two arcs. The characteristic of TIG-MIG welding process is discussed compared to single MIG. It lays the foundation for the further research on the interaction of the two arcs during TIG-MIG hybrid welding.     

冬季东海、南黄海中DMS和DMSP浓度分布及影响因素研究

于2011年12月~2012年1月现场测定了东海、南黄海表层海水中二甲基硫(DMS)及其前体物质二甲巯基丙酸内盐(DMSP分为溶解态DMSPd和颗粒态DMSPp)的含量,研究了它们的浓度分布规律及其影响因素,并对DMSPp的粒级分布和DMS的海-气通量进行了探讨.结果表明,表层海水中DMS、DMSPd和DMSPp的浓度分别在0.58~4.14、0.37~7.86和4.29~25.76 nmol·L-1之间,平均值分别为(2.20±0.82)、(2.12±1.66)和(11.98±6.23)nmol·L-1.DMS、DMSPp与叶绿素a(Chl-a)呈现明显的正相关关系,并且它们的周日变化趋势基本一致,说明浮游植物生物量是影响研究海域内DMS和DMSP生产分布的关键因素.另外,DMSPd浓度和总细菌丰度表现出一定的负相关,这可能是在细菌释放的DMSP裂解酶的作用下DMSPd会发生裂解生成DMS.研究发现,5~20μm的微型浮游植物是海区内Chl-a和DMSPp的主要贡献者.此外,冬季东海、南黄海表层海水DMS的海-气通量在0.61~25.52μmol·(m2·d)-1之间,平均值为(8.30±5.92)μmol·(m2·d)-1.