TiO2 nanotubes as solid-phase extraction adsorbent for the determination of polycyclic aromatic hydrocarbons in environmental water samples

An analytical method based on TiO2 nanotubes solid-phase extraction (SPE) combined with gas chromatography (GC) was established for the analysis of seven polycyclic aromatic hydrocarbons (PAHs): acenaphtylene, acenaphthene, anthracene, fluorene, phenanthrene, fluoranthene and pyrene. Factors a ecting the extraction e ciency including the eluent type and its volume, adsorbent amount, sample volume, sample pH and sample flow rate were optimized. The characteristic data of analytical performance were determined to investigate the sensitivity and precision of the method. Under the optimized extraction conditions, the method showed good linearity in the range of 0.01–0.8 g/mL, repeatability of the extraction (RSD were between 6.7% and 13.5%, n = 5) and satisfactory detection limits (0.017–0.059 ng/mL). The developed method was successfully applied to the analysis of surface water (tap, river and dam) samples. The recoveries of PAHs spiked in environmental water samples ranged from 90% to 100%. All the results indicated the potential application of titanate nanotubes as solid-phase extraction adsorbents to pre-treat water samples.     

提高煤层气采收率的CO2埋存技术

作为常规油气重要接替补充的非常规天然气,煤层气越来越受到世人的关注.如何提高煤层气采收率是摆在煤层气开发工程师面前迫切需要解决的技术难题.通过向煤层中注入CO2,既可以提高煤层气采收率又能间接地实现CO2减排,即提高煤层气采收率的CO2埋存技术(CO2-ECBM).该项技术已在世界各地迅速发展,并取得一些实质性进展.文...     

环评监测现场采样中应注意的问题

根据环境影响评价监测的要求,提出了环评监测中方案的细化、点位布设方面存在的问题,阐述了如何合理设置监测点位、准确把握采样方法、科学选择分析方法等问题。     

Review of the progress in preparing nano Ti02： An important environmental engineering material

TiO2 nanomaterial is promising with its high potential and outstanding performance in photocatalytic environmental applications, such as CO2 conversion, water treatment, and air quality control. For many of these applications, the particle size, crystal structure and phase, porosity, and surface area influence the activity of TiO2 dramatically. TiO2 nanomaterials with special structures and morphologies, such as nanospheres, nanowires, nanotubes, nanorods, and nanoflowers are thus synthesized due to their desired characteristics. With an emphasis on the different morphologies of TiO2 and the influence factors in the synthesis, this review summarizes fourteen TiO2 preparation methods, such as the sol-gel method, solvothermal method, and reverse micelle method. The TiO2 formation mechanisms, the advantages and disadvantages of the preparation methods, and the photocatalytic environmental application examples are proposed as well.     

丹东市降水pH值及酸雨分析

分析2013年大气降水pH值及近10年历史演变的方法分析丹东市酸雨污染现状、特征,并从污染源和气候条件解释酸雨形成的原因,确定酸雨的形成受外来空气污染物影响较大,而酸雨强度的大小具有本地环境条件和环境污染特征。     

火电厂低氮燃烧改造技术的应用

本文介绍了氮氧化物产生的机理以及低氮燃烧技术在火电厂大型燃煤锅炉的应用,简述其技术特点和改造措施,并通过试验测试了改造后的效果。     

重金属阳离子荧光传感器合成及光谱性研究

通过亚胺缩合的反应制备出阳离子荧光传感器（Cation Fluorescent Sensors,CFSs）,并对其结构、光谱性能检测、荧光量子产率等进行了详细的研究.通过荧光化学传感器产生的荧光光谱一直是高效的分析方法,因此合成了新的基于席夫碱的荧光化学传感器,并研究了对各种金属离子的结合特性.在CH3CN溶液中测试了阳离子荧光传感器时不同阳离子的选择性响应,发现对Cu2＋有较好的选择性,可用于Cu2＋的检测.该类阳离子荧光传感器是基于2,2-联噻吩-5-乙醛的荧光发射基团和邻氨基苯甲醚为识别基团的一类阳离子荧光传感器.     

流化床O2/CO2气氛燃煤痕量元素的排放特性及控制

通过平顶山烟煤在小型流化床中的燃烧实验,采用X-射线荧光光谱仪(XRF)对低压撞击器(LPI)收集到的细颗粒物元素组成进行定量测定,研究了O2/CO2气氛下硅藻土对煤粉燃烧痕量元素的排放控制.结果表明,Zn、Mn和Ni的含量随粒径呈双峰分布,峰值分别在0.1μm和2μm附近,Hg和Co的含量在0.1μm附近有一峰值;Hg和Zn在亚微米颗粒上有一定程度的富集,Mn、Ni和Co在亚微米和超微米颗粒上的含量基本相当;当颗粒物粒径一定时,随着硅藻土含量的增加,5种元素的富集因子呈减小的趋势;随着添加剂粒径的减小,颗粒物中Hg、Mn、Zn、Ni和Co的含量呈减少的趋势;当颗粒物粒径一定时,5种元素含量顺序为MnZnNiCoHg.     

树脂基固态胺吸附剂室温下对低浓度CO2的吸附性能研究

以大孔甲基丙烯酸酯吸附树脂为载体,聚乙烯亚胺(PEI)为有机胺,采用液相浸渍法制备出固态胺吸附剂,并研究了其在室温下对低浓度CO2的吸附行为.同时,利用氮气吸附、热重分析和扫描电镜表征了材料的物理化学性质,并采用热重法和固定床吸附法考察了材料的CO2吸附性能.结果表明,大孔树脂担载50%PEI(质量分数)时吸附性能最佳,对纯CO2的最大吸附量为175 mg·g-1;CO2的吸附行为由扩散动力学与吸附热力学共同决定,低温有利于提高吸附容量;吸附剂对400 ppm~15%浓度的CO2都具有优异的动态吸附性能,其中对400 ppm CO2的吸附量达到86 mg·g-1,对15%CO2的吸附量达到150 mg·g-1;湿度对吸附起促进作用,相对湿度为10%时,对400 ppm CO2的吸附量提高至139mg·g-1;吸附剂具有优异的循环性能,具有直接空气捕集CO2的潜力.     

基于RFPA2D复合局部挠曲岩体数值模拟

为研究复合局部挠曲岩体强度特征以及破坏规律,采用岩石真实破裂软件RFPA^2D,对水平层面挠曲30°,45°,60°,75°的复合岩体进行单轴压缩试验模拟。模拟结果表明:挠曲角为30°,45°,60°,75°的复合岩体破坏面几乎与挠曲段夹层重合,其挠曲端部均产生了垂直于挠曲段夹层的裂纹;复合单斜岩体与复合挠曲岩体破坏面的形成因素大致相同,夹层强度是2种岩体失稳的主要因素;复合挠曲岩体单轴抗压强度随挠曲角增大同样呈“U”型变化,与单斜岩体变化趋势一致;当水平层状岩体发生挠曲后,其单轴抗压强度减小,当挠曲角为60°时,强度降低25.19%,当挠曲角为75°时,强度降低0.17%。;随着均质系数m的增大,复合挠曲岩体单轴抗压强度以及轴向应变均出现逐渐递增的趋势,且不同m值,其岩体裂隙扩展方式具有明显差别。