聚硅酸铝铁/羧基壳聚糖复合絮凝剂处理硫化黑染料废水的研究

用聚硅酸铝铁/羧基壳聚糖复合絮凝剂对硫化黑染料废水进行了处理,研究了影响絮凝剂处理硫化黑染料废水的影响因素。结果表明,较佳的条件为转速50 r/min、聚硅酸铝铁和羧基壳聚糖的质量配比为3、废水pH值为9.0、絮凝剂用量为60 mg/L。在该条件下,复合絮凝剂对硫化黑染料废水的COD、色度、浊度去除率分别为92.1%,88.6%,96.3%。     

Enhanced debromination of 2,2′,4,4′-tetrabromodiphenyl ether (BDE-47) by zero-valent zinc with ascorbic acid

• Highly efficient debromination of BDE-47 was achieved in the ZVZ/AA system. • BDE-47 debromination by the ZVZ/AA can be applied to a wide range of pH. • AA inhibits the formation of (hydr)oxide and accelerates the corrosion of ZVZ. • Reduction mechanism of BDE-47 debromination by the ZVZ/AA system was proposed. A new technique of zero-valent zinc coupled with ascorbic acid (ZVZ/AA) was developed and applied to debrominate the 2,2′,4,4′-Tetrabromodiphenyl ether (BDE-47), which achieved high conversion and rapid debromination of BDE-47 to less- or non-toxic forms. The reaction conditions were optimized by the addition of 100 mg/L ZVZ particles and 3 mmol/L AA at original solution pH= 4.00 using the solvent of methanol/H₂O (v:v= 4:6), which could convert approximately 94% of 5 mg/L BDE-47 into lower-brominated diphenyl ethers within a 90 min at the ZVZ/AA system. The high debromination of BDE-47 was mainly attributed to the effect of AA that inhibits the formation of Zn(II)(hydr)oxide passivation layers and promotes the corrosion of ZVZ, which leads to increase the reactivity of ZVZ. Additionally, ion chromatography and gas chromatography mass spectrometry analyses revealed that bromine ion and lower-debromination diphenyl ethers formed during the reduction of BDE-47. Furthermore, based on the generation of the intermediates products, and its concentration changes over time, it was proposed that the dominant pathway for conversion of BDE-47 was sequential debromination and the final products were diphenyl ethers. These results suggested that the ZVZ/AA system has the potential for highly efficient debromination of BDE-47 from wastewater.     

钢铁企业大型低位料仓汽车卸料的粉尘控制

某钢企大型低位料仓为汽车卸料,料仓厂房内空高,跨度大,料仓上部贯通,物料落差大,卸料中产生大量粉尘,环境污染问题典型突出。通过对低位料仓汽车卸料产尘特性分析,采取加强生产管理、组织汽车有序卸料、料仓厂房有效密闭、合理设计捕尘方式和布袋除尘系统等措施,能够有效地控制粉尘污染。除尘系统具有投资及运行费用少,除尘效果明显的优点。     

铁炭复配修复地下水中NO_3~--N的条件研究

采用了铁炭复配修复地下水中NO3--N,探讨了实验条件对修复效果的影响。结果表明,在pH值近中性条件(初始pH 6.42)下,反应时间为1 h时NO3--N修复率达到60.85%;Fe/C=1∶1时介质最佳用量分别为4~5 g;Fe/C=1/1.5时修复率为72.80%;反应速率在高振荡强度下大于低振荡强度;氧化铜的催化效果最好,可使修复率提高7.5个百分点。铁炭复配介质修复地下水中NO3--N是有效可行的,修复率随反应时间的增加而提高,在Fe/C=1∶1时修复率与介质用量呈正相关,无限减小Fe/C比并不能无限提高修复率,振荡强度对修复具有显著影响,低振荡强度下的修复过程较高强度存在滞后现象,并非所有金属氧化物催化剂对铁炭修复NO3--N均有促进作用。     

树脂固载纳米铁对偶氮染料直接湖蓝5B的脱色性能研究

以FeSO4和NaBH4水溶液为前驱溶剂,以聚苯乙烯型阳离子交换树脂为载体,制备了树脂固载的纳米铁,室温下用于对偶氮染料直接湖蓝5B水溶液进行脱色研究。研究结果发现,脱色反应遵循准一级反应动力学,在初始pH为3~10的范围内,反应进行14 m in时,50 mg/L的染料溶液脱色率均能达到83%以上。固载的纳米铁材料可多次重复利用,溶液中释放的铁离子浓度不超过0.1 mg/L。     

酸性矿井水中和沉淀法除铁优化

针对山西某煤矿高矿化度、高铁酸性矿井水除铁效果差、出水容易返色等问题,采用NaOH中和调pH、曝气及化学氧化等处理工艺进行酸性矿井水中和沉淀法除铁优化实验研究。结果表明,采用NaOH中和沉淀法除铁时,投加中和剂使出水pH达6.7以上时,出水中铁含量低于10 mg/L,满足排放要求。对于本实验废水NaOH所需投加量为2.8 g/L,铁的去除率可达到99.75%;以H2O2对原水进行氧化处理,可迅速将Fe(Ⅱ)氧化成Fe(Ⅲ),其用量与原水中Fe(Ⅱ)的含量成正比。当其用量为1.6 mL/L时,可将原水中的Fe(Ⅱ)完全转化为Fe(Ⅲ),投加中和剂使出水pH达到4.5以上时,能使出水中铁含量满足排放要求。对于实验废水所需的NaOH投加量为2.0 g/L,比直接中和沉淀所需的NaOH用量要节省28.6%。曝气处理对原水中Fe(Ⅱ)的氧化效果不明显。     

铁氧化物复合氧化铝催化臭氧化过程中溴酸盐的生成控制

以市售活性炭、硅藻土和氧化铝小球为载体,考察了负载铁基活性组分对催化臭氧化过程中溴酸盐的控制情况,其中,铁基复合氧化铝小球体现出更好的溴酸盐还原特性和催化剂稳定性,证实催化剂中铁氧化物是溴酸盐得到有效控制的主要活性组分。进一步考察了铁基复合氧化铝小球催化臭氧化处理实际原水过程中对溴酸盐的生成控制,以及反应过程中溶解性有机碳（DOC）的去除情况。结果表明,与单独臭氧化相比,该催化剂既能有效去除水中的溶解性有机物,又能明显抑制溴酸盐的生成,反应50h,其活性并没有明显下降。催化剂失活主要归因于吸附位点数量的下降,可以通过负载铁氧化物来实现催化剂的再生。     

Adsorption of As(III) on chitosan-Fe-crosslinked complex (Ch-Fe)

It was reported the adsorption of As(III) on the surface of the chitosan-Fe-crosslinked complex. Theoretical correlation of the experimental equilibrium adsorption data for As(III)/Ch-Fe system is best explained by the non-linearized form Langmuir-Freundlich isotherm model. At optimum conditions, pH 9.0, the maximum adsorption capacity, calculated using the Langmuir-Freundlich isotherm model was 13.4 mg g⁻¹. The adsorption kinetics of As(III) onto Ch-Fe are described by the pseudo-first-order kinetic equation. The results of the Mössbauer spectroscopy showed that there is no redox process on the surface of the adsorbent.     

Dechlorination of PCBs in the simulative transformer oil by microwave-hydrothermal reaction with zero-valent iron involved

The conventional hydrothermal reaction with iron powder, NaOH and H₂O as reactants was reported to occur at temperature above 423 K, and iron oxides (Fe₃O₄ and NaFeO₂) and hydrogen were produced. In this study, microwave heating was adopted to take the place of conventional heating to induce the hydrothermal reaction. Under microwave irradiation, NaOH and H₂O absorbed microwave energy by space charge polarization and dipolar polarization and instantly converted it into thermal energy, which initiated the hydrothermal reaction that involved with zero-valent iron. X-ray diffraction (XRD) analysis found Fe₃O₄/NaFeO₂ and confirmed the occurrence of microwave-induced hydrothermal reaction. The developed microwave-hydrothermal reaction was employed for the dechlorination of PCBs. Hexadecane containing 100 mg L⁻¹ of Aroclor1254 was used as simulative transformer oil, and the dechlorination of PCBs was evaluated by GC/ECD, GC/MS and ion chromatography. For PCBs in 10 mL simulative transformer oil, almost complete dechlorination was achieved by 750 W microwave irradiation for 10 min, with 0.3 g iron powder, 0.3 g NaOH and 0.6 mL H₂O added. The effects of important factors including microwave power and the amounts of reactants added, on the dechlorination degree were investigated, moreover, the dechlorination mechanism was suggested. Microwave irradiation combined with the common and cheap materials, iron powder, NaOH and H₂O, might provide a fast and cost-effective method for the treatment of PCBs-containing wastes.     

Zero-valent iron nanoparticles in treatment of acid mine water from in situ uranium leaching

Acid mine water from in situ chemical leaching of uranium (Straz pod Ralskem, Czech Republic) was treated in laboratory scale experiments by zero-valent iron nanoparticles (nZVI). For the first time, nZVI were applied for the treatment of the real acid water system containing the miscellaneous mixture of pollutants, where the various removal mechanisms occur simultaneously. Toxicity of the treated saline acid water is caused by major contaminants represented by aluminum and sulphates in a high concentration, as well as by microcontaminants like As, Be, Cd, Cr, Cu, Ni, U, V, and Zn. Laboratory batch experiments proved a significant decrease in concentrations of all the monitored pollutants due to an increase in pH and a decrease in oxidation-reduction potential related to an application of nZVI. The assumed mechanisms of contaminants removal include precipitation of cations in a lower oxidation state, precipitation caused by a simple pH increase and co-precipitation with the formed iron oxyhydroxides. The possibility to control the reaction kinetics through the nature of the surface stabilizing shell (polymer vs. FeO nanolayer) is discussed as an important practical aspect.