传统活性污泥法与膜生物反应器污泥沉降性能的比较

针对污泥沉降性能,在运行条件相同的情况下对膜生物反应器(MBR)与传统活性污泥法(CAS)进行比较。结果表明：CAS工艺污泥沉降性能优于MBR工艺;CAS工艺出水水质受污泥沉降性能影响大;MBR工艺污泥沉降性能主要由反应器中累积的高浓度胞外聚合物(EPS)含量所影响,当EPS浓度大于100mg／g时,污泥沉降性能开始恶化;CAS工艺曝气池中EPS浓度没有累积;MBR工艺污泥颗粒平均粒径小于CAS工艺中污泥颗粒。     

基于FBM法追踪秦皇岛海域赤潮迁移扩散

在Delft3D-FLOW模型模拟水动力的基础上,基于FBM粒子追踪法建立和验证赤潮迁移扩散模型.模拟了秦皇岛海域潮流和风生流,分析了风生流对赤潮迁移扩散的作用,对比分析了FBM法、拉格朗日法和常规布朗运动法在赤潮迁移扩散模拟中的特性,测试了模型Hurst指数的敏感性并得出其在赤潮模拟中的合理取值范围.主要结论为：①秦皇岛海域的赤潮主要随潮流的涨落而往复移动,一个涨落潮周期内赤潮的净迁移距离较小;②秦皇岛海域夏季潮流较弱,但风对赤潮迁移具有一定影响,易产生东北向风生流,导致赤潮更易往东北方向迁移;③Hurst指数较明显地影响粒子云的扩散范围,Hurst指数取0.80±0.03能比较真实地模拟秦皇岛海域赤潮的迁移扩散;④FBM法可模拟赤潮的non-Fickian扩散现象,使其模拟的粒子云扩散范围和分布形状明显优于拉格朗日法和常规布朗运动法.     

Key features of new particle formation events at background sites in China and their influence on cloud condensation nuclei

New particle formation (NPF) event at multi rural sites in China Identifying the characteristics of NPF event Comparing NPF event between clean and polluted conditions Quantifying contribution to the cloud condensation nuclei Implication of climate and air quality Long-term continuous measurements of particle number size distributions with mobility diameter sizes ranging from 3 to 800 nm were performed to study new particle formation (NPF) events at Shangdianzi (SDZ), Mt. Tai (TS), and Lin’an (LAN) stations representing the background atmospheric conditions in the North China Plain (NCP), Central East China (CEC), and Yangtze River Delta (YRD) regions, respectively. The mean formation rate of 3-nm particles was 6.3, 3.7, and 5.8 cm⁻³·s⁻¹, and the mean particle growth rate was 3.6, 6.0, and 6.2 nm·h⁻¹ at SDZ, TS, and LAN, respectively. The NPF event characteristics at the three sites indicate that there may be a stronger source of low volatile vapors and higher condensational sink of pre-existing particles in the YRD region. The formation rate of NPF events at these sites, as well as the condensation sink, is approximately 10 times higher than some results reported at rural/urban sites in western countries. However, the growth rates appear to be 1–2 times higher. Approximately 12%–17% of all NPF events with nucleated particles grow to a climate-relevant size (>50 nm). These kinds of NPF events were normally observed with higher growth rate than the other NPF cases. Generally, the cloud condensation nuclei (CCN) number concentration can be enhanced by approximately a factor of 2–6 on these event days. The mean value of the enhancement factor is lowest at LAN (2–3) and highest at SDZ (~4). NPF events have also been found to have greater impact on CCN production in China at the regional scale than in the other background sites worldwide.     

无锡市大气PM2.5中黑碳的粒径分布与混合态特征

针对长江三角洲地区PM2.5中的重要组分黑碳(BC)气溶胶,2010~2011年利用单颗粒黑碳光度计(SP2),对江苏省无锡市夏冬两季BC气溶胶的质量浓度、粒径分布及单颗粒混合态进行了连续在线观测.结果表明,无锡市冬季BC质量浓度(6.1μg/m3)是夏季(2.5μg/m3)的2.4倍,内混态BC比例(NIB)冬季(64.8%)也显著高于夏季(44.6%),说明冬季BC污染与来外来污染传输有关.反向轨迹分析表明,来自华北平原的污染气团输入是冬季高浓度BC污染的首要原因. NIB的日变化趋势与BC质量浓度的完全相反.午后BC质量浓度最低时NIB最高,反映了二次光化学产物包覆在BC颗粒外层的老化过程.此外,夏冬两季BC粒径分布保持稳定,其质量浓度峰值对应粒径在225nm左右,数浓度峰值对应粒径在120nm左右.     

西安市大气颗粒物数浓度分布及典型天气条件特征变化

利用2013年3月到2014年12月期间西安市大气中0.25～32μm颗粒物监测数据和同期气象参数、散射消光系数等数据,分析了大气颗粒物数浓度分布及典型天气条件下变化特征.结果表明:采样期间西安市大气颗粒物平均数浓度为206.27个/cm3, 99%以上为<1μm的颗粒物数.大气颗粒物数浓度冬季最高,其次为秋、夏和春季,分别为267.66、231.31、141.82和135.77个/cm3.四季的数浓度低值均出现在18:00左右,之后数浓度上升,且晚上高于白天,冬季6:00左右达到峰值,夏季的昼夜差最小,秋季最大.春夏秋冬的大气颗粒物数浓度与散射消光系数的Pearson相关系数分别为0.756、0.702、0.411、0.377.大气颗粒物数浓度在沙尘天气发生前、中、后会升高、下降和再下降,霾天气出现前、后会升高和下降;高温干燥天气下,大气颗粒物数浓度相对较低;降雨对大气颗粒物的清除作用明显,但降雨后大气颗粒物数浓度又很快回升.     

二氧化硫/水/空气体系气溶胶成核实验研究

以X-射线为辐射电离源对二氧化硫/水/空气体系的气溶胶成核过程进行了研究.实验结果表明,新生粒子来源于离子诱导成核与均相成核两种机制,前者产生带电颗粒,后者产生中性颗粒.离子对粒子成核有着重要的贡献,对粒子生长作用不明显,SO2对粒子成核与生长均有贡献.成核粒子谱分布呈双峰模式,其峰值会随着气体流速发生偏移.在低SO2浓度情况下,离子诱导成核占主导地位,随着SO2浓度的增加,均相成核的作用越来越明显.     

北京大气降尘中微量元素的空间变异

在北京市六环内均匀布点采集了城市核心区、城市扩展区、近郊区的大气降尘.对降尘中14种稀土元素(Y、Pm除外)以及Cr、Co、Mo、Cd、Pb等5种重金属元素的化学特征进行统计分析,并结合判别分析和Spearman相关分析方法阐释了影响各区域空间变异的主要元素.最后利用三角图解法揭示空间差异的成因.结果表明,各元素含量在空间上具有明显的阶梯变化,Cr、Mo、Cd、Pb含量沿城市核心区向近郊区方向呈递减趋势,Co与14种稀土元素含量的梯度变化特征则恰好相反,由市中心向外围郊区呈递增趋势.轻稀土富集程度表现为城市核心区>城市扩展区>近郊区,Eu亏损程度相反.Mo、Co、Pb元素可用来表征区域降尘的空间差异(68.2%).LaCeSm三角图解表明北京降尘主要来源于壳源物质.PbCoMo和CrCoMo三角图解可以很好地解释不同污染源贡献程度的差别是造成降尘中微量元素在空间尺度上的差异的原因.近郊区降尘受到土壤扬尘、燃煤的影响较大.城市核心区降尘主要受到交通排放的影响.城市扩展区处于过渡带,降尘受到交通、燃煤、土壤扬尘等的影响作用居中.     

黄山大气气溶胶新粒子生长特性观测分析

利用2012年9月22日~10月28日黄山地区大气气溶胶、二氧化硫和臭氧观测数据,结合气象数据,分析气溶胶新粒子的生成-增长特征.分析发现,在33个有效观测日中,有新粒子生成-增长的观测日占总数的18.2%,其中晴天的发生频率为37.5%,新粒子生成-增长都开始于晴天上午,与无新粒子观测日相比,太阳辐射量、风速、SO2及O3浓度较高,环境温度和相对湿度较低.气溶胶新粒子的增长具有由小及大的特点,核模态气溶胶粒子(10~20nm)数浓度最先增加,爱根核模态粒子(20~50nm)数浓度随着时间推移逐渐增大,但浓度峰值依次下降,平均增长率为3.58nm/h. SO2浓度先于核模态气溶胶数浓度到达峰值,其氧化后的产物H2SO4为新粒子的核化提供前体物,并且参与新粒子的增长过程,当SO2浓度较低时,不会发生新粒子生长事件.     

正丁醇对柴油机颗粒组分与形貌特征的影响

为探讨柴油机燃用正丁醇-柴油混合燃料降低颗粒排放的机理,采用热重分析仪与场发射扫描电子显微镜,重点对正丁醇-柴油混合燃料燃烧的颗粒形貌特征进行研究,分析了颗粒的组分、微观结构以及粒径分布随w(正丁醇)的变化规律. 结果表明:正丁醇-柴油混合燃料燃烧的颗粒呈团簇状结构,随着w(正丁醇)的增加,团聚程度逐渐提高,排列结构更加紧密;颗粒的粒径逐渐减小,柴油、B5、B10〔B5、B10是指w(正丁醇)分别为5%、10%的正丁醇-柴油混合燃料〕燃烧的颗粒平均粒径分别为1.43、0.85、0.52 μm;颗粒中的主要成分为碳烟,其质量分数约为60%,随着w(正丁醇)的增加,碳烟和可溶有机物组分的质量分数有所增加,硫酸盐、金属等不易挥发组分以及金属元素的质量分数逐渐减少. 研究显示,添加正丁醇,可促进颗粒转化、改善颗粒的氧化过程,使颗粒向小粒径方向移动;由于颗粒中可溶有机物组分含量增加,因此提高了颗粒在碰撞过程中凝并的概率,致使颗粒的团聚程度增加.      

Effects of molecular weight and concentration of carboxymethyl cellulose on morphology of hydroxyapatite nanoparticles as prepared with one-step wet chemical method

Nano-sized apatite particles (nAP) synthesized with carboxymethyl cellulose (CMC) have shown great application potentials in in situ heavy metal remediation. However, differences in CMC’s properties effects on the size of nAP produced are not well understood. In this paper, two types of CMC, with respective molecular weights (MW) of ～120000 and ～240000 Dalton or respective polymerization degrees of 500 (CMC-500) and 1050 (CMC-1050), were studied in a concentration range of 0.05%–0.5% (w/w) for nAP synthesis. Morphology of the particles was characterized with transmission electron microscopy (TEM). Results showed that 0.05% CMC-500 solution gave an average particle size of 148.7±134.9 nm, 0.25% CMC-500 solution produced particles of 21.8±20.4 nm, and, 0.5% CMC-500 solution contained particles of 15.8±7.7 nm. In comparison, 0.05% CMC-1050 solution produced nanoparticles of 6.8±3.2 nm, 0.25% CMC-1050 produced smaller nAP of 4.3±3.2 nm, and 0.5% CMC-1050 synthesized the smallest nanoparticles in this study, with an average diameter of 3.0±2.1 nm. Chemical composition of the products was identified with X-ray diffraction (XRD) as pure hydroxyapatite. Interactions between nAP and CMC were discussed with help of attenuated total reflection Fourier transform infrared (ATRFTIR) spectroscopic data. This study showed that CMC at higher concentration as well as higher MW facilitated to produce finer nanoparticles, showing that nAP size could be manipulated by selecting appropriate CMC MW and/or applying appropriate CMC concentration.