粗石英砂层厚度及倾角对核废物处置库顶盖毛细屏障效应的影响

毛细屏障作为核废物处置库顶盖的工程屏障之一,已经在国内外得到了广泛应用.采用箱体实验方法,研究了非饱和稳定流条件下粗石英砂层厚度和倾角对毛细屏障效应的影响.结果表明,随着粗石英砂层厚度的增大,水分的相对绕流量增大,毛细屏障效应增强;随着粗石英砂层倾角的增大,其表面积水减少,水的横向流动能力增强,毛细屏障效应增强.     

星形大分子液晶在气相色谱分析中的应用研究

将首次合成的偶氮苯硅氧烷类星形液晶大分子化合物用于毛细管柱气相色谱固定液 ,在其相转变温度附近具有良好的选择性 ,成功地分离了二甲酚异构体。     

气相色谱测定土壤中微量阿特拉津

采用丙酮加水提取土壤中的阿特拉津,再用三氯甲烷萃取,经浓缩、定容后,用毛细管气相色谱法测定.     

Preparation of steel slag porous sound-absorbing material using coal powder as pore former

The aim of the study was to prepare a porous sound-absorbing material using steel slag and fly ash as the main raw material, with coal powder and sodium silicate used as a pore former and binder respectively. The influence of the experimental conditions such as the ratio of fly ash, sintering temperature, sintering time, and porosity regulation on the performance of the porous sound-absorbing material was investigated. The results showed that the specimens prepared by this method had high sound absorption performance and good mechanical properties, and the noise reduction coefficient and compressive strength could reach 0.50 and 6.5 MPa, respectively. The compressive strength increased when the dosage of fly ash and sintering temperature were raised. The noise reduction coefficient decreased with increasing ratio of fly ash and reducing pore former, and first increased and then decreased with the increase of sintering temperature and time. The optimum preparation conditions for the porous sound-absorbing material were a proportion of fly ash of 50% (wt.%), percentage of coal powder of 30% (wt.%), sintering temperature of 1130°C, and sintering time of 6.0 hr, which were determined by analyzing the properties of the sound-absorbing material.     

基于放射性碳分析的多环芳烃源解析:技术进展和准确性评估

化石燃料燃烧和生物质燃烧是污染物多环芳烃(polycyclic aromatic hydrocarbon,PAHs)的两大来源.放射性碳(14C)分析近年用于评估这两类源对环境中PAHs的相对贡献.此方法基于化石燃料和生物质的14C含量差异,即化石燃料不含14C,而生物质的14C浓度有一个较稳定值.14C的自然丰度极低(约10-12),因此检测PAHs这样的痕量污染物的14C含量一度极具挑战.1990年代中期,加速器质谱的技术突破使得对环境样品PAHs的14C分析具有实用价值.要准确测出PAHs的14C含量,须先从化学成分复杂的环境样品中分离出高纯度的PAHs.制备气相色谱因其出色的分离能力而成为目前环境样品PAHs14C分析必备的工具.本文意在简介基于14C分析的PAHs源解析的基本原理、技术进展,以及评估该方法获得的PAHs源解析结果的准确性.     

SiO2气凝胶隔热性能的影响因素研究

目的 在不同热流条件下,通过调整SiO2气凝胶的孔隙率、涂层厚度等,以满足合适的隔热要求。方法 针对中短程飞行器飞行时外壁面承受短时高热流的特点,在分析孔隙率对SiO2气凝胶热导率影响规律的基础上,通过数值仿真研究不同气凝胶孔隙率、气凝胶厚度及热流作用下的温度响应。结果 得到了不同条件下满足隔热要求的气凝胶最小厚度,以及气凝胶表面的最高温度。高温情况下,气凝胶孔隙率为96%时,有效热导率最低,孔隙率超过96%时,隔热性能变差。结论 当飞行器内壁面温度满足要求时,增大气凝胶的孔隙率,则需要减小气凝胶的厚度,相应的气凝胶表面温度会升高,但升幅很小。当飞行器外壁面承受长时间大热流时,仅调整气凝胶的厚度和孔隙率不能达到结构的隔热要求。     

pH-dependent leaching behaviour and other performance properties of cement-treated mixed contaminated soil

Portland cement has been widely used for stabilisation/solidification (S/S) treatment of contaminated soils. However, there is a dearth of literature on pH-dependent leaching of contaminants from cement-treated soils. This study investigates the leachability of Cu, Pb, Ni, Zn and total petroleum hydrocarbons (TPH) from a mixed contaminated soil. A sandy soil was spiked with 3000 mg/kg each of Cd, Cu, Pb, Ni and Zn, and 10,000 mg/kg of diesel, and treated with ordinary Portland cement (CEM I). Four different binder dosages, 5%, 10%, 15% and 20% (m/m) and different water contents ranging from 13%-19% dry weight were used in order to find a safe operating envelope for the treatment process. The pH-dependent leaching behaviour of the treated soil was monitored over an 84-day period using a 3-point acid neutralisation capacity (ANC) test. The monolithic leaching test was also conducted. Geotechnical properties such as unconfined compressive strength (UCS), hydraulic conductivity and porosity were assessed over time. The treated soils recorded lower leachate concentrations of Ni and Zn compared to the untreated soil at the same pH depending on binder dosage. The binder had problems with Pb stabilisation and TPH leachability was independent of pH and binder dosage. The hydraulic conductivity of the mixes was generally of the order, 10^-8 m/sec, while the porosity ranged from 26%-44%. The results of selected performance properties are compared with regulatory limits and the range of operating variables that lead to acceptable performance described.     

炭化压力对编织C/C复合材料致密过程及结构的影响

目的研究不同炭化压力环境对C/C复合材料致密过程及结构的影响。方法通过浸渍/高压炭化工艺在不同炭化压力下制备高温煤沥青炭块及沥青基C/C复合材料,并研究不同炭化压力环境下对其密度和孔隙的影响。结果制备沥青炭的炭化压力由20 MPa增大至60 MPa时,沥青炭体积密度由1.08 g/cm~3增加至1.39g/cm~3,质量比表面积由14.74增加至16.51,开孔率由26.73减少至7.94,孔隙填充效果明显改善,浸渍-炭化的增密效率得到提升。结论在编织C/C材料的致密过程中,压力越大,其孔隙越小,分布越均匀,故产品致密效果越好。     

渐变型多孔介质中低浓度瓦斯燃烧特性数值模拟

利用模拟软件Fluent6.3建立二维模型并进行合理设置,对多孔介质中的煤矿低浓度瓦斯燃烧进行数值模拟,研究了均匀型和渐变型燃烧器中的温度分布和NOx生成情况,以及三种不同渐变型多孔介质组合燃烧器中的温度分布和NOx生成情况。结果表明,渐变型多孔介质燃烧器的温度分布比均匀型燃烧器更加均匀;同一瓦斯当量比和流速下,渐变型多孔介质燃烧器的NOx产生量比均匀型燃烧器低很多,有利于减少污染物排放;三种不同渐变型多孔介质组合的温度分布和NOx生成有着不同特点,燃烧器设计时,可根据不同需求选取不同组合形式,综合考虑各因素,组合一燃烧特性最佳。     

表面活性剂在甲烷氧化菌降解煤体甲烷中的适用性研究

甲烷氧化菌液在进入煤储层后会产生较高的毛管压力,且随着甲烷氧化菌降解煤层瓦斯的进行,毛管压力逐渐增大,容易引起水锁伤害。采取向甲烷氧化菌菌液加入复配表面活性剂以期减缓菌液造成的水锁伤害,通过测试所选表面活性剂十二烷基苯磺酸钠（SDBS）与椰子油脂肪酸二乙醇酰胺（CDEA）对菌液表面张力的降低程度来了解表面活性剂与菌液的配伍比例,并对含复配表面活性剂的甲烷氧化菌对煤层甲烷的降解进行研究。研究结果表明:表面活性剂与菌液最佳配伍比例为SDBS∶CDEA为1∶4,最佳配伍浓度为0.5％,且表面活性剂在菌液中稳定性较好;菌液中添加复配表活剂20 mL,在混合气体压力为2 MPa、氧浓度为 1％、温度为 30 ℃时,添加复配表面活剂菌液的甲烷最终降解率为51.65％,比未添加复配表面活剂菌液高出11％左右。因此,向甲烷氧化菌菌液中添加复配表面活性剂具有很好的适用性。