冷挤大型法兰面螺母的工艺研究

以大型法兰面螺母为例 ,论述了用无缝钢管冷挤大型法兰面螺母工艺的可行性     

方头柱塞冷挤镦工艺及模具设计

分析了硬铝合金方头柱塞件的冷挤镦工艺 ,设计了方头柱塞冷挤镦件图 ,计算及选用了毛坯形状及尺寸 ,验算了许可变形程度 ,选择了冷成形用的设备 ,拟制了冷挤镦工艺前的毛坯处理并设计了方头柱塞冷挤镦模具结构。     

应用低温等离子体技术治理空气污染研究进展

低温等离子体技术在治理空气污染方面以其效率高、能耗低、适用范围广等特点而成为研究热点.本文介绍了低温等离子体的概念及分类,概述了国内外利用单一低温等离子体技术及其与吸附、催化协同、多性能颗粒混合物结合治理空气污染的最新进展,指出了存在的问题并讨论了今后的研究方向和应用前景.     

Effect of Sweating on Insulation of Footwear

The study aimed to find out the influence of sweating on footwear insulation with a thermal foot model. Simultaneously, the influence of applied weight (35 kg), sock, and steel toe cap were studied. Water to 3 sweat glands was supplied with a pump at the rate of 10 g/hr in total. Four models of boots with steel toe caps were tested. The same models were manufactured also without steel toe. Sweating reduced footwear insulation 19–25% (30–37% in toes). During static conditions, only a minimal amount of sweat evaporated from boots. Weight affected sole insulation: Reduction depended on compressibility of sole material. The influence of steel toe varied with insulation. The method of thermal foot model appears to be a practical tool for footwear evaluation.     

QUALITY OF HYDROMETEOROLOGICAL DATA IN COLD REGIONS1

ABSTRACT: Many users of hydrometeorological records are not aware of the number of inconsistencies and biases that occur in hydrometeorological records. Examples are presented illustrating how the exposures of sites for measurement of precipitation, wind, snow on the ground, and evaporation determine to a large extent how useful the records are for estimating areal conditions. For areas where precipitation in the form of snow produces a significant portion of the runoff, a smaller number of quality records may be more valuable for modeling than a much larger number of records of lower quality. Information is presented to show that the overall value of an operational hydrometeorological network is dependent upon how consistent and representative of average conditions the collected records are, especially for mountainous areas in cold regions.     

耐冷菌在低温下处理污水的研究进展

低温污水的生物处理一直是水处理领域的难点和热点,由于耐冷菌对温度的适应范围较宽,且在低温下仍然保持较高的代谢活性,因此在污水处理和污染环境生物修复领域中的应用逐渐受到重视。本文介绍了耐冷菌在环境中的分布、主要种类以及适冷机理,概述了耐冷菌在工业废水和生活污水处理中的主要研究进展。指出应进一步开发环境中耐冷菌菌种资源,揭示耐冷菌的冷适应特性和功能表达之间的关系,加强耐冷菌在水体修复与净化领域的理论和应用研究,从而为我国北方尤其是东北地区的水环境保护提供行之有效的新途径。     

难切削零件的冷挤压工艺

以“尾钉”为例 ,分析高温合金的难切削工艺特点 ,设计合理可行的冷挤压工艺     

冷轧带钢轧辊温度场及其控制

分析了冷轧过程中工作辊的温度变化及热凸度的形成 ,提出了控制热凸度的有效手段 ,对完善板型控制系统具有重要的意义     

VE泵端面凸轮冷/温复合成形技术研究

采用温锻制坯与冷摆辗相结合的复合成形工艺生产VE泵端面凸轮精密成形件,不仅材料利用率可达到95%左右;而且成形件的尺寸精度高,表面光洁度高,能有效地减少后续仿形磨削加工的余量,从而降低了生产成本,提高了生产效率。采用该工艺可以进行大批量生产,能满足我国轻型汽车VE泵的生产需要。     

介质阻挡放电降解苯乙烯的研究

研究了介质阻挡放电(DBD)常压下降解流动态苯乙烯时,不同电压、流速、初始浓度及湿度下苯乙烯的降解情况.结果表明,DBD降解苯乙烯15~20min即可达稳定,产物主要为CO、CO₂和H₂O;电压4800V时有少量带苯环的气态及固态物质产生,且随电压的升高而减少,到7500V时红外光谱已无法检测到;高电压下放电可以取得90%左右的降解率,产生带苯环的气态物质和结焦物质较少.流速在1.5cm/s,浓度为3000mg/m³,相对湿度为20%左右时,降解效果最好.