贫燃条件Ag-Rh/CeO_2-ZrO_2-Al_2O_3协同催化C_3H_6选择性还原NO的原位红外研究

将Ag-Rh浸渍到共沉淀法合成的Ce-Zr-Al上,制备出Ag(0.04)-Rh(x)/Ce0.5Zr0.5O2-75%Al2O3系列催化剂,采用BET比表面积、X射线衍射光谱(XRD)和原位漫反射傅里叶变换红外光谱(DRIFTS)对催化剂进行表征,并探讨催化剂在贫燃条件下选择性还原NO的活性和反应机理.结果表明,Ag-Rh双组分催化剂的活性较单组分Ag、Rh催化剂的高.Rh负载量为0.7%(质量分数)时,NO转化率达最佳(90.3%),且反应的起燃温度低、活性温度范围宽(300～500℃).DRIFTS结果显示,Rh的添加不仅有利于催化剂表面NO的吸附,而且能促进Ag催化生成关键反应中间体—CO—NH—,进而显著提高NO的转化率.     

DNBP生产废水处理工艺探讨

4,6二硝基邻仲丁基苯酚(DNBP)生产过程产生的废水,采用化学与生物处理组合工艺,结合生产实际,分流治理,使DNBP得以充分的回收。纳米TiO2负载活性炭、臭氧催化氧化,降低COD、增加废水的可生化性。针对废水中的可溶性有机物,培养特效菌群生化处理,出水稳定,达国家二级排放标准。     

粉煤灰处理Cr~(6+)废水的试验研究

利用电厂粉煤灰进行了处理含铬(VI)废水试验,探讨了粉煤灰投加量、pH值、接触时间、温度和含铬浓度等因素对除铬效果的影响。结果表明,在废水pH=10左右、Cr6+浓度<100mg/L,粉煤灰的用量140g/L时,在常温下吸附处理2h,对铬的去除率可达到72%以上。粉煤灰吸附处理含铬废水符合Freundlich等温式,以物理吸附为主。对于低浓度含铬(VI)的废水,处理后可达标排放。     

Synergistic removal of aniline by carbon nanotubes and the enzymes of Delftia sp. XYJ6

Synergistic removal of aniline by carbon nanotubes and the enzymes of Delftia sp. XYJ6, a newly isolated bacterial strain for biodegrading aniline, was investigated. It showed that biodegradation rate of aniline was increased with the augment of protein concentration in cell-free extract of Delftia sp. XYJ6. The adsorption amount of aniline by multi-walled carbon nanotubes (MWCNTs) was slightly higher than that by single-walled carbon nanotubes (SWCNTs), however the adsorption amount of protein of Delftia sp. XYJ6 by MWCNTs was lower than that by SWCNTs. Much more amount of aniline could be removed by CE of Delftia sp. XYJ6 in the presence of SWCNTs than MWCNTs, which indicated that an efficient reaction between aniline and enzymes of Delftia sp. XYJ6 on the surface of SWCNTs played a key role in the rapid enzymatic biodegradation of aniline. This study is not previously reported and may be useful in basic research and the removal of aniline from wastewater.     

Improving the stability,lithium diffusion dynamics,and specific capacity of SrLi2Ti6O14 via ZrO2 coating

SrLi2Ti6O14 (SLTO) coated with different amount of ZrO2 was successfully prepared. The as-obtained composites are stacked by a series of particles with a pure phase structure and a good crystallinity. Furthermore, ZrO2 coating not only enhances the structural stability of the materials but also facilitates the diffusion of lithium through the SEI film. As a result, the redox polarization was reduced, and the reversibility of the electrochemical reaction was enhanced. Particularly, SLTO-ZrO2-2 sample delivers a high initial lithiation capacity of 283.6 mA h g-1, and the values maintain at 251.7, 228.0, 207.4, 175.3, and 147.7 mA h g-1 at the current densities of 0.13, 0.26, 0.54, 1.31, and 2.62 A g-1, respectively. Our experiment also confirmed that SLTO materials coated with ZrO2 are suitable for high power density applications, and the lithiation specific energy efficiency of SLTO-ZrO2-2 is 200％as high as that of pure SLTO at a power density of 1257 W kg-1.     

Fabrication of highly efficient Bi2WO6/CuS composite for visible-light photocatalytic removal of organic pollutants and Cr(VI) from wastewater

• A novel Bi₂WO₆/CuS composite was fabricated by a facile solvothermal method. • This composite efficiently removed organic pollutants and Cr(VI) by photocatalysis. • The DOM could promoted synchronous removal of organic pollutants and Cr(VI). • This composite could be applied at a wide pH range in photocatalytic reactions. • Possible photocatalytic mechanisms of organic pollutants and Cr(VI) were proposed. A visible-light-driven Bi₂WO₆/CuS p-n heterojunction was fabricated using an easy solvothermal method. The Bi₂WO₆/CuS exhibited high photocatalytic activity in a mixed system containing rhodamine B (RhB), tetracycline hydrochloride (TCH), and Cr (VI) under natural conditions. Approximately 98.8% of the RhB (10 mg/L), 87.6% of the TCH (10 mg/L) and 95.1% of the Cr(VI) (15 mg/L) were simultaneously removed from a mixed solution within 105 min. The removal efficiencies of TCH and Cr(VI) increased by 12.9% and 20.4%, respectively, in the mixed solution, compared with the single solutions. This is mainly ascribed to the simultaneous consumption electrons and holes, which increases the amount of excited electrons/holes and enhances the separation efficiency of photogenerated electrons and holes. Bi₂WO₆/CuS can be applied over a wide pH range (2–6) with strong photocatalytic activity for RhB, TCH and Cr(VI). Coexisiting dissolved organic matter in the solution significantly promoted the removal of TCH (from 74.7% to 87.2%) and Cr(VI) (from 75.7% to 99.9%) because it accelerated the separation of electrons and holes by consuming holes as an electron acceptor. Removal mechanisms of RhB, TCH, and Cr(VI) were proposed, Bi₂WO₆/CuS was formed into a p-n heterojunction to efficiently separate and transfer photoelectrons and holes so as to drive photocatalytic reactions. Specifically, when reducing pollutants (e.g., TCH) and oxidizing pollutants (e.g., Cr(VI)) coexist in wastewater, the p-n heterojunction in Bi₂WO₆/CuS acts as a “bridge” to shorten the electron transport and thus simultaneously increase the removal efficiencies of both types of pollutants.     

Bioaerosolization behavior along sewage sludge biostabilization

• Aerosolization behavior during a lab-scale sludge biostabilization was determined. • Many pathogenic species were identified to be preferentially aerosolized. • Bioaerosol concentration along the biostabilization ranged from 160 to 1440 cell/m³. • Sludge aerosolization behavior was different with that of other biowaste. Biostabilization is a cost-effective method for the beneficial utilization of sewage sludge. However, during the operation of sludge biostabilization, some microbial species could be released into the atmospheric environment from the solid-phase of sludge easily and present a high risk to human health. This study aimed to evaluate the risk of bioaerosol during sludge biostabilization. We found a total of nine bacterial phyla, one archaeal phylum, and two fungal phyla in the bioaerosol samples. Among them, Proteobacteria, Actinobacteria, Bacteroidetes, and Ascomycota were the dominant phyla. In addition, the bioaerosolization indexes (BI) of prokaryotic phyla and fungal phyla ranged 0–45 and 0–487, respectively. Massilia, Pseudarthrobacter, Pseudomonas, Tremellales spp., and Fusarium were the preferentially aerosolized microbial genera with maximum bioaerosolization indexes of 19962, 10360, 1802, 3055, and 7398. The bioaerosol concentration during the biostabilization ranged from 160 to 1440 cell/m³, and we identified species such as Stenotrophomonas rhizophila and Fusarium graminerum with high bioaerosolization indexes that could be threats to human health. Euryachaeota, which belongs to archaeal phyla, had the highest biostabilization index in our study. We also found that Pseudarthrobacter was the easiest to aerosolize during the sludge biostabilization process.