化学法处理电镀废水的自动化控制应用

采用化学法自动控制处理含铬和含镍电镀废水,选择合适的化学药剂和pH、ORP控制参数,连续式处理电镀废水.运行结果表明:该工艺简单、处理效果良好、运行稳定、可操作性好、运行成本适中、能很好的适应水质的波动,处理后的水质完全符合排放标准.     

Removal of Cu(II) from acidic electroplating effluent by biochars generated from crop straws

The removal efficiency of copper(Cu(Ⅱ)) from an actual acidic electroplating effluent by biochars generated from canola,rice,soybean and peanut straws was investigated.The biochars simultaneously removed Cu(Ⅱ) from the effluent,mainly through the mechanisms of adsorption and precipitation,and neutralized its acidity.The removal efficiency of Cu(Ⅱ) by the biochars followed the order:peanut straw char > soybean straw char > canola straw char > rice straw char a commercial activated carbonaceous material,which is consistent with the alkalinity of the biochars.The pH of the effluent was a key factor determining the removal efficiency of Cu(Ⅱ) by biochars.Raising the initial pH of the effluent enhanced the removal of Cu(Ⅱ) from it.The optimum pyrolysis temperature was 400°C for producing biochar from crop straws for acidic wastewater treatment,and the optimum reaction time was 8 hr.     

电镀行业清洁生产指标体系的修正

文章旨在通过剖析清洁生产指标体系建立的全过程,发现《电镀行业清洁生产指标体系(试行)》存在的缺陷与不足,并进行修正,采用层次分析法对修正后的定量指标体系赋权.最后选用三家电镀企业,对修正前后的指标体系进行评价与对比,并据此证明:修正后的指标体系更能客观评价企业真实的清洁生产水平.     

火焰原子吸收光谱法测定电镀废水中高浓度的锡

采用盐酸消解样品,用火焰原子吸收光谱法测定电镀废水中高浓度的锡的质量浓度,方法简单可靠。通过实验样品的分析,验证了方法的准确度和精密度。该方法干扰少,数据准确,适合废水分析。     

电镀综合废水对DF膜的污染

江苏某电镀厂的电镀综合废水在采用DF膜进行预处理时,膜易受到污染。针对这一问题,采用DF膜生产厂家提供的小试装置,研究探索了膜污染的原因及其具体特征。实验结果表明,在处理电镀综合废水时,DF膜的污染速率较快,而酸洗对DF膜的恢复性较好,研究还证实电镀综合废水中的无氰沉锌水洗液是造成DF膜污染的主要原因。     

电镀污泥的热处理特性以及对金属回收的影响

焙烧-酸浸法可有效回收电镀污泥中的有价金属,而污泥的热处理特性是决定能否采用焙烧预处理的重要因素。研究了氧化焙烧和还原焙烧对污泥成分和金属浸出性的影响,并对焙烧前后的污泥进行了金属形态分析和X射线衍射(XRD)分析。结果表明,焙烧预处理实现了污泥减量和金属富集;ES1经氧化焙烧后金属浸出率接近原泥,Cu的浸出率达99%;ES2的还原焙烧效果优于氧化焙烧,特别是Cu的浸出率超过97%,XRD分析发现,还原焙烧过程中金属Cu被还原为铁铜合金;2种焙烧均造成了ES3中目标金属Ni的浸出率的降低;金属浸出性的下降与残渣态的形成有关。     

Profitability of in-plant modifications in pollution control

This case study was developed in view of setting up a demonstration project on “revealing the profitability of clean technology in small-scale electroplating unit”. The research was conducted in a small-scale electroplating shop located in Bangkok. A set of simple in-plant control measures such as dragout recovery, spray rinsing technique and rinse water agitation were implemented. Quantitative data, obtained from the monitoring of wastewater before and after process modifications, have indicated a substantial reduction both in quantity and strength of wastewater generated. Water consumption was reduced by approx. 35% of total rinsing water, which is 19% of total process water consumption. Average metal concentrations in wastewater was reduced 73% for Cr-, 71% for Ni- and 54% for Cu-plating rinse water.     

生物强化/混凝沉淀工艺处理电镀园区物化出水的试验研究

试验采用生物强化/混凝沉淀工艺处理电镀工业园区的物化出水,重点考察了本工艺对进水COD、氨氮的去除效果.结果表明,生物强化工艺能有效降低废水中的COD、氨氮,混凝沉淀工艺能进一步去除废水中的污染物.当进水COD在200～ 350 mg/L、氨氮在20～35 mg/L时,出水水质能够达到《电镀污染物排放标准》(GB 21900-2008)中表2的标准,即COD≤80 mg/L、氨氮≤15 mg/L.     

乡镇工业电镀行业主要污染物排放量的估算方法

电镀分有氰电镀与无氰电镀两类。乡镇工业电镀行业的环境污染最主要是氰污染和铬污染。本文针对乡镇电镀行业的特点,调查了湖南省沅江市、四川省新都县、湖北省黄陂县、汉川县以及江苏省部分县市乡镇电镀厂,将收集资料及实际监测资料进行回归分析,得出乡镇电镀行业的污染物发生量大小与原材料的消耗有关,可以用多元回归方程估算乡镇电镀行业主要污染物发生量。这一估算方法简单易行,实用可靠,操作方便。     

混合电镀废水处理工艺

物化法是处理混合电镀废水的一种有效方法,对COD、Pb离子、Ni离子尤其是Pb离子、Ni离子的处理效果非常理想。COD的去除率达到80.1%,Pb离子的去除率达到97.2%,Ni离子的去除率达到98.1%,中间产出的污泥也可得到较好处理。