冬季低温下MBR与CAS工艺运行及微生物群落特征

研究了在冬季低温条件下,膜生物反应器(MBR)与传统活性污泥法(CAS)工艺运行效果及微生物群落特征的差异,对工艺出水水质和微生物活性进行了分析,并借助454焦磷酸高通量测序法对微生物群落组成和结构进行了解析.结果表明,三套对比工艺(MBR两套:高污泥浓度R1和低污泥浓度R2,CAS工艺R3)的出水总氮平均去除率分别为85.2%、56.1%、58.8%;NH+4-N的平均去除率分别为99.7%、99.7%、59.7%,比硝化速率由大到小依次为R2、R1、R3,比反硝化速率由大到小依次为R3、R1、R2,高浓度MBR污泥具有较好的耐寒特性和氨氮去除效果;从454焦磷酸测序结果看,相似性为97%时,菌群丰富度:R2>R3>R1,多样性:R2>R1>R3;MBR污泥微生物菌群的组成和丰度与CAS系统有较大不同;R1、R2、R3中主要的硝化菌为Nitrospira菌属,总相对度依次为:1.22%、1.64%、0.15%,主要的反硝化菌为Zoogloea菌属、Thauera菌属、Comamonadaceae菌属及Comamonas菌属,总相对丰度依次为:5.8%、4.52%、15.21%;低温环境下,泥龄长、污泥浓度高、TN负荷低的MBR系统有利于硝化、反硝化细菌累积,提升生物脱氮效果.     

高效聚磷菌Alcaligenes sp. ED-12菌株的分离鉴定及其除磷特性

利用经典的微生物筛选方法,从福州市闽侯县上街镇高岐村某排污口淤泥中分离出1株高效聚磷菌,并结合16S rRNA基因序列分析进行了菌株鉴定.结果表明,该菌株为产碱杆菌,将其命名为Alcaligenes sp.ZGED-12.理化因素实验显示,在以乙酸钠为碳源、NH4Cl为氮源,当C/N为3∶1,pH为8.0,温度和摇床转速分别为35℃和100 r·min-1时,该菌株的生长状态最好,对磷的去除能力也最强,最高除磷率可达80%.此外,该菌株能够耐受较高浓度的磷,当磷浓度超过45 mg·L-1时会产生抑制效应.同时,以聚乙烯醇(PVA)和海藻酸盐(SA)制备了聚磷微生物固定化小球,并考察了菌球对氮磷废水的净化效果.结果表明,氮磷的去除包括固定化材料的吸附作用及微生物的生长利用和/或贮存,显示出了良好的应用前景.     

基于相关性分析的PCBA热力学模型修正

目的精确且高效地对印制电路板组件热力学模型进行修正。方法采用基于拉丁超立方抽样试验设计和Speraman等级相关系数计算公式的相关性分析方法,找出电子产品热仿真试验中对元器件表面温度值影响较大的输入参数,然后进一步分析得出输入与输出之间的函数关系。在此基础上给出印制电路板组件(PCBA)热力学模型修正的一般方法流程。最后利用该方法对某航空电子产品中一块PCBA的热力学模型进行修正。结果修正结果较精确且只调用2次有限元软件。结论该热模型修正方法具有较高的精确性和高效性,可推广用于工程实践。     

低DO下AGS-SBR处理低COD/N生活污水长期运行特征及种群分析

本研究在序批式活性污泥反应器(SBR)中接种好氧颗粒污泥(AGS),构成AGS-SBR系统,研究其在低DO(0.5~1.0mg·L~(-1))条件下,处理低COD/N比(4.0)生活污水同步脱氮除磷的长期稳定运行特性,并解析反应器的主要菌群构成.结果表明,在反应器运行的180d里,AGS-SBR系统表现出了良好且稳定的除污能力,反应器对水体中COD、NH~+_4-N、TN和TP平均去除率分别达到87.17%、95.21%、77.05%和91.11%.好氧颗粒污泥沉降性能一直很好,污泥始终保持着完整的颗粒外观和密实紧凑的结构,并没有出现明显的颗粒污泥解体的现象.同时,高通量测序结果表明,变形菌门、厚壁菌门、绿菌门、绿弯菌门和拟杆菌门为SBR-AGS反应器中主要优势菌群.Denitratisoma、Planctomycetaceae、Thauera、Comamonas、Nitrosomonas和Nitrospira是反应器中与脱氮有关菌群;Clostridium和Anaerolinea是除磷相关细菌.     

牛粪厌氧发酵的载体筛选试验研究

为了提高厌氧发酵装置的效率,人们研究了各种各样的方法和措施,其中应用填料或载体使生物菌能够延长驻留期是其中的方法之一,开展载体筛选及其结构设计在厌氧发酵装置中的试验,有助于对此问题的深入研究以及将其成果应用于生产实践。通过静态载体筛选试验选择了玻璃纤维作为载体、PVC塑料管作为载体骨架制成的装置在动态序批式厌氧发酵装置中进行了试验。结果表明：此载体骨架结构对于牛粪动态厌氧发酵具有明显的提高产气效率、改变产气质量和促进有机物转化为挥发性脂肪酸的作用。     

A fluorescence-based bioassay for aquatic macrophytes and its suitability for effect analysis of non-photosystem II inhibitors

Background, Goals and Scope During the last years the miniaturization of toxicity test systems for rapid and parallel measurements of large quantities of samples has often been discussed. For unicellular algae as well as for aquatic macrophytes, fluorescence-based miniaturized test systems have been introduced to analyze photosystem II (PSII) inhibitors. Nevertheless, high-throughput screening should also guarantee the effect detection of a broad range of toxicants in order to ensure routinely applicable, high-throughput measuring device experiments which can cover a broad range of toxicants and modes of action others than PSII inhibition. Thus, the aim of this study was to establish a fast and reproducible measuring system for non-PSII inhibitors for aquatic macrophyte species to overcome major limitations for use. Methods A newly developed imaging pulse-amplitude-modulated chlorophyll fluorometer (I-PAM) was applied as an effect detector in short-term bioassays with the aquatic macrophyte species Lemna minor. This multiwell-plate based measuring device enabled the incubation and measurement of up to 24 samples in parallel. The chemicals paraquat-dichloride, alizarine and triclosan were chosen as representatives for the toxicant groups of non-PSII herbicides, polycyclic aromatic hydrocarbons (PAHs) and pharmaceuticals and personal care products (PPCPs), which are often detected in the aquatic environment. The I-PAM was used (i) to establish and validate the sensitivity of the test system to the three non-PSII inhibitors, (ii) to compare the test systems with standardized and established biotests for aquatic macrophytes, and (iii) to define necessary time scales in aquatic macrophyte testing. For validation of the fluorescence-based assay, the standard growth test with L. minor (ISO/DIS 20079) was performed in parallel for each chemical. Results The results revealed that fluorescence-based measurements with the I-PAM allow rapid and parallel analysis of large amounts of aquatic macrophyte samples. The I-PAM enabled the recording of concentration-effect-curves with L. minor samples on a 24-well plate with single measurements. Fluorescence-based concentration-effect-curves could be detected for all three chemicals after only 1 h of incubation. After 4–5 h incubation time, the maximum inhibition of fluorescence showed an 80–100% effect for the chemicals tested. The EC50 after 24 h incubation were estimated to be 0.06 mg/L, 0.84 mg/L and 1.69 mg/L for paraquatdichloride, alizarine and triclosan, respectively. Discussion The results obtained with the I-PAM after 24 h for the herbicide paraquat-dichloride and the polycyclic aromatic hydrocarbon alizarine were in good accordance with median effective concentrations (EC50s) obtained by the standardized growth test for L. minor after 7 d incubation (0.09 mg/L and 0.79 mg/L for paraquat-dichloride and alizarine, respectively). Those results were in accordance with literature findings for the two chemicals. In contrast, fluorescence-based EC50 of the antimicrobial agent triclosan proved to be two orders of magnitude greater when compared to the standard growth test with 7 d incubation time (0.026 mg/L) as well as with literature findings. Conclusion Typically, aquatic macrophyte testing is very time consuming and relies on laborious experimental set-ups. The I-PAM measuring device enabled fast effect screening for the three chemicals tested. While established test systems for aquatic macrophytes need incubation times of ≥ 7 d, the I-PAM can detect inhibitory effects much earlier (24 h), even if inhibition of chemicals is not specifically associated with PSII. Thus, the fluorescence-based bioassay with the I-PAM offers a promising approach for the miniaturization and high-throughput testing of chemicals with aquatic macrophytes. For the chemical triclosan, however, the short-term effect prediction with the I-PAM has been shown to be less sensitive than with long-term bioassays, which might be due to physicochemical substance properties such as lipophilicity. Recommendations and Perspectives The results of this study show that the I-PAM represents a promising tool for decreasing the incubation times of aquatic macrophyte toxicity testing to about 24 h as a supplement to existing test batteries. The applicability of this I-PAM bioassay on emergent and submerged aquatic macrophyte species should be investigated in further studies. Regarding considerations that physicochemical properties of the tested substances might play an important role in microplate bioassays, the I-PAM bioassay should either be accompanied by evaluating physicochemical properties modeled from structural information prior to an experimental investigation, or by intensified chemical analyses to identify and determine nominal concentrations of the toxicants tested. The chemicals paraquat-dichloride, alizarine and triclosan were chosen as representatives for the toxicant groups of non-PSII herbicides, PAHs and PPCPs which are often detected in the aquatic environment. Nevertheless, in order to ensure a routinely applicable measuring device, experiments with a broader range of toxicants and samples of surface and/or waste waters are necessary. ESS-Submission Editor: Dr. Markus Hecker (MHecker@Entrix.com)     

固定CO2氢细菌的筛选及其培养条件优化

从土壤中分离筛选到一株高效固定CO2 的氢氧化细菌—专性化能自养菌BHA 15 ,在最佳培养条件下(培养基 ρ/gL-1:NH4 Cl 4.0 ,Na2 HPO4 ·12H2 O 0 .75 ,KH2 PO4 0 .5 ,MgSO4 ·7H2 O 0 .3;V(H2 )∶V(O2 )∶V(CO2 ) =3 .5∶1∶1;pH =7;最适生长温度θ =30℃ ) ,密闭摇瓶中恒温 (30℃ )培养 40h后 ,菌体浓度 ρ(DW)达 1.6mg/mL ,菌体蛋白含量 71.8% .图 7表 2参 12     

水处理中微生物絮凝剂产生菌的选育及应用

综述了微生物絮凝剂产生菌筛选和培育方面的研究进展,介绍了微生物絮凝剂在给水和饮用水、乳化液的油水分离、污水处理等领域的应用,以及廉价培养基的探索实践。提出针对影响微生物絮凝剂产生菌生长代谢的环境条件开展深入研究,同时寻找或设计廉价培养基,降低生产成本,推动其工业化应用。     

军用集成电路质量控制方法分析与探讨

集成电路是军用电子设备最重要的器件之一,集成电路的质量直接影响到军用装备的质量。从集成电路的选择、二次筛选和破坏性物理分析(DPA)这几个方面探讨了军用集成电路的质量控制方法。实践证明通过质量控制筛选得到的集成电路整批使用可靠性都有明显的提高。     

Screening risk areas for sediment and phosphorus losses to improve placement of mitigation measures

Identification of vulnerable arable areas to phosphorus (P) losses is needed to effectively implement mitigation measures. Indicators for source (soil test P, STP), potential mobilization by erosion (soil dispersion), and transport (unit-stream power length-slope, LS) risks were used to screen the vulnerability to suspended solids (SS) and P losses in two contrasting catchments regarding topography, soil textural distribution, and STP. Soils in the first catchment ranged from loamy sand to clay loam, while clay soils were dominant in the second catchment. Long-term SS and total P losses were higher in the second catchment in spite of significantly lower topsoil STP. A higher proportion of areas in the second catchment were identified with higher risk due to the significantly higher risk of overland flow generation (LS) and a significantly higher mobilization risk in the soil dispersion laboratory tests. A simple screening method was presented to improve the placement of mitigation measures.