Biodegradation of phenol and m-cresol by mutated Candida tropicalis

The phenol and m-cresol biodegradations were studied using the mutant strain CTM 2 obtained by the He-Ne laser irradiation on wild-type Candida tropicalis. The results showed that C. tropicalis exhibited the increased capacity of phenolic compounds degradation after laser irradiation. It could degrade 2600 mg/L phenol and 300 mg/L m-cresol by 5% inoculum concentration, respectively. In the dual-substrate biodegradation system, 0–500 mg/L phenol could accelerate m-cresol biodegradation, and 300 mg/L m-cresol could be completely utilized within 46 hr at the presence of 350 mg/L phenol. Besides, the maximum biodegradation of m-cresol could reach 350 mg/L with 80 mg/L phenol within 61 hr. Obviously, phenol, as a growth substrate, could promote CTM 2 to degrade m-cresol, and was always preferentially utilized as carbon source. Comparatively, low-concentration m-cresol could result in a great inhibition on phenol degradation. In addition, the kinetic behaviors of cell growth and substrate biodegradation were described by kinetic model proposed in our laboratory.     

阜山金矿区构造应力场及其转化的恢复

本文估算了阜山金矿区成岩成矿期构造差应力值 ,获得近 2km2 内主压应力和差异应力的空间分布规律 ,结果表明矿体部位往往对应于应力应变强烈变化区段 ,而并非极高值或极低值处。通过应变测量和磁组构分析 ,得到阜山金矿成岩期和成矿期构造应变场特征 ,指出阜山金矿构造应力场在成矿期经历了由NW向挤压转为NE向挤压转化的特征 ,这次转化对该区成矿意义重大     

成形工艺对轿车减振器座应变状态影响的研究

通过网格应变分析技术 ,对某轿车采用一次成形、两次成形工艺冲制减振器座的应变状态进行了定量研究 ,结果表明 ,成形工艺对减振器座的应变分布、应变路径、应变大小影响很大 ,一次成形较两次成形对材料的成形性能要求较高 ,两次成形工艺更有利于零件成形     

润滑油高效降解菌的筛选及降解性能

实验以被石油污染的土壤为出发菌源,以润滑油为唯一碳源,经过筛选分离得到4株对润滑油具有降解能力的菌株。经过形态观察、生理生化实验初步鉴定发现,4株菌株分别为黄单胞菌属(Xanthomonas)、动胶菌属(Azotobac-ter)、假单胞菌属(Pseudomonas)和黄杆菌属(Flavobacterium),其中菌株G4为黄杆菌属,其润滑油降解效率最高。研究菌株G4降解性能的影响因素发现,实验中的各因素对润滑油降解率的影响大小依次为:温度>葡萄糖浓度>硫酸铵浓度>pH值。在温度20～40℃下,菌株G4对润滑油均具有一定的降解能力。在适宜的温度范围中,pH值5.0～9.0范围内,菌株G4的润滑油降解率随pH值的变化很小,且均在80%以上。菌株G4在以润滑油为唯一碳源时的最佳培养条件为:温度30℃,pH值为9.0,硫酸铵浓度为1.0 g/L。在此条件下培养36 h,100 mL的G4培养液对200μL润滑油的降解率可达84.6%。     

基因工程菌E.coli BL21-NiCoT吸附镍的性能研究

以表达Staphylococcus aureus ATCC6538镍钴转运酶NiCoT基因的基因工程菌E.coli BL21-NiCoT作为生物吸附剂处理含镍废水.结果表明:基因工程菌在pH为4～9时有比较好的吸附效果,30 min就达到了吸附平衡;基因工程菌对Ni2 的富集容量比原始宿主菌有很大的提高,最大平衡富集量从3.76 mg/g增加到11.33 mg/g,增幅达3倍多,溶液中Ni2 的最大去除率也从原来的35.62%增加到91.23%;Cu2 、Cr6 、Zn2 等的存在对吸附没有很大的影响.镍进入细胞内后与羟基和酰胺基团发生结合,蛋白类物质和含羟基类物质在细胞内富集镍的过程中起到重要作用;基因工程菌转接10、20、30、40、50次,重组质粒保持良好的结构稳定性,基因工程菌对镍的富集能力也具有较好的稳定性.     

油烟污染物降解优势菌株的筛选及性能研究

在完成对活性污泥驯化的基础上,分离、纯化出XJ9,XJ30,XJ2,XJ21,XJ28,XJ25等6株油烟污染物降解细菌,研究其生长条件及降解性能,筛选出一株优势菌株并进行菌落形态学及分子生物学鉴定。实验结果表明:6株细菌最适生长温度在35℃左右、最适pH在6⁸之间、最佳摇床转速介于808之间、最佳摇床转速介于80¹60 r/min之间,各菌株最佳降解时间均为36 h,对油烟污染物的降解率介于12%160 r/min之间,各菌株最佳降解时间均为36 h,对油烟污染物的降解率介于12%⁶0%之间,其中XJ25最高可达到60%左右,可确定XJ25为油烟污染物降解优势菌株。经分子生物学鉴定,确定XJ25为干燥棒状杆菌(Corynebacterium xerosis)。所获得的油烟污染物降解菌对于应用生物法降解餐饮油烟污染物具有一定的价值。     

石油烃类降解菌分离筛选及其特性的实验

通过选择性培养从被石油污染土壤中分离出2株能够以机油为碳源和能源的菌株LL1和LL2,测定了温度、底物浓度和pH值对其降解能力的影响,确定了最佳生长条件,并试验了菌株对正己烷、苯和甲苯的降解能力。实验表明,2种菌株都对机油有较强的降解能力,在实验最适条件下分别达到53%和77%,其中LL2菌株还对苯和甲苯有一定的降解能力,具有较好的应用前景。     

The shaped blasting experimental study on damage and crack evolution of high stress coal seam

In the deep high stress coal and rock mass, the efficiency of the ordinary blasting method is constantly affected by the high pressure. This study investigates the shaped blasting technology with increased blasting efficiency, develops a mechanical model for coal crack expansion during shaped blasting, and examines the force-energy action of energy-gathering jets during coal splitting. The established model was combined with experiments and simulations to reveal the damage and evolution of cracks in coal and rock masses. Experiments demonstrate that shaped blasting can create an energy-gathering jet that causes a directional fracture in the test block. The peak of compressive strain in the energy-gathering direction is 1.12 times greater than that of ordinary blasting, and the static action period of the explosive gas is prolonged by 1.3 μs according to the stress curve. Moreover, the peak pressure strain increased 3.2 times, and the pull strain peak increased 3.92 times. The damage amount was represented by the resistivity and ultrasonic wave speed, and shaped blasting causes 1.2 and 1.5 times greater damage than ordinary blasting. The research results provide technical methods for safe and rapid penetration blasting in deep high-ground stressed coal mines.