利用废弃物衍生燃料的热化学处理法制富含氢气合成气

为了探讨利用热化学方式从城市垃圾中制取富含氢气合成气过程的要素影响,解析氢气发生特性及其与主要影响要素之间的关系。在分析了城市生活垃圾组分特性的基础上,将其加工成组分均一的废弃物衍生燃料(refuse de-rived fuel,RDF),并在700、800和900℃等3个温度条件下,分别开展了RDF的热解、气化及水蒸汽气化等实验。研究表明,RDF的加工不但可有效降低垃圾含水率,还可将垃圾热值提高近1倍。温度和添加水蒸汽是从RDF中制取富含氢气合成气过程中的关键影响要素。其中,温度对氢气生成起到至关重要的决定作用,温度的提高对促进H2浓度的提高有利,同时,在气化过程中添加水蒸汽,可有效促进CO和H2等有价气体组分生成。在900℃的高温水蒸汽气化处理过程中,可获得H2浓度最高为34.13%的合成气。另外,800℃热解过程所产生的合成气热值最高,达到14 509 kJ/Nm3。     

Hydroxytyrosol, the phenolic compound of olive oil protects human PBMC against oxidative stress and DNA damage mediated by 2,3,7,8-TCDD

The protective effect of hydroxytyrosol (HT), a strong antioxidant compound from extra virgin olive oil, against TCDD induced toxicity was investigated in human peripheral blood mononuclear cells (PBMC). PBMC (1 × 10⁶ cells mL⁻¹) were divided into four groups and were incubated in a CO₂ incubator (5% CO₂) for 12 h with vehicle, TCDD (10 nM), TCDD + HT (10 nM + 100 μM) and HT alone (100 μM) respectively. To clarify the role of HT against TCDD induced cytotoxicity, oxidative stress and the levels of antioxidant enzymes were assessed. Incubation of PBMC with TCDD significantly decreased cell viability, catalase (CAT) and glutathione peroxidase (GPx) and increased the levels of superoxide dismutase (SOD), glutathione reductase (GR) and oxidative stress markers such as lipid peroxidation products (LPO), protein carbonyl content (PCC) and reactive oxygen species (ROS). Whereas, HT had an effective antioxidant property as observed by the increased cell viability, normalization of antioxidant enzymes and decreased levels of LPO, PCC and ROS in PBMC co-treated with HT and TCDD. Apoptosis detection and comet assay results shows that HT, by acting as an antioxidant, prevents the damage to DNA induced by TCDD. In addition light microscopic and histopathological observations revealed that the cells are apoptotic and degenerated during TCDD treatment, whereas cells showed intact morphology during co-treatment with HT. On the whole, the results reveal that HT exerts a promising antioxidant potential in protecting the PBMC against TCDD induced oxidative stress, which might be due to the presence of catechol moiety in its structure.     

蒽醌修饰石墨毡电极预处理头孢合成废水

以钛涂钌电极为阳极、自制蒽醌修饰石墨毡电极为阴极,对头孢合成废水(COD=25 000~30 000 mg/L、ρ(NH3-N)=850~1 300 mg/L、色度为2 300~2 680度)进行了电化学氧化预处理,优化了电解条件,并对电化学体系的动力学和稳定性进行了分析。实验结果表明:蒽醌的存在可改善电化学氧化降解效果;在电解时间50 min、电流密度0.14 A/cm2、Na2SO4浓度0.1 mol/L、极板间距2 cm、初始废水p H 7.0的条件下,废水的COD、色度、NH3-N的去除率分别可达45.3%,66.9%,33.6%;BOD5/COD由处理前的0.27增至0.40,可生化性得到改善;COD、色度、NH3-N的电化学氧化降解过程均近似符合一级动力学方程;且该电化学体系的应用稳定性良好。     

COMPARISON OF REGRESSION AND TIME-SERIES METHODS FOR SYNTHESIZING MISSING STREAMFLOW RECORDS1

ABSTRACT: Regression and time-series techniques have been used to synthesize and predict the stream flow at the Foresta Bridge gage from information at the upstream Pohono Bridge gage on the Merced River near Yosemite National Park. Using the available data from two time periods (calendar year 1979 and water year 1986), we evaluated the two techniques in their ability to model the variation in the observed flows and in their ability to predict stream flow at the Foresta Bridge gage for the 1979 time period with data from the 1986 time period. Both techniques produced reasonably good estimates and forecasts of the flow at the downstream gage. However, the regression model was found to have a significant amount of autocorrelation in the residuals, which the time-series model was able to eliminate. The time-series technique presented can be of great assistance in arriving at reasonable estimates of flow in data sets that have large missing portions of data.     

Biodegradable plastic made from soybean products. II. Effects of cross-linking and cellulose incorporation on mechanical properties and water absorption

Soy isolate was treated with formaldehyde and glyoxal at 1.0, 2.5, and 5.0% (w/w isolate) and with adipic and acetic anhydrides. The materials were then compression-molded into plastic tensile bars and tested for tensile and yield strength, percentage elongation, Young's modulus, and water absorption. Treatment with 5% formaldehyde increased the tensile strength significantly, to 4.9 kg/mm², compared with the untreated sample (3.7 kg/mm²). The yield strength increased slightly, to 0.68 kg/mm². Elongation was significantly less after treatment with formaldehyde. Young's modulus increased after treatment and leveled off at 174 kg/mm². Water absorption decreased as the formaldehyde concentration increased. Treatment with either glyoxal or adipic/acetic anhydride had a detrimental effect on the mechanical properties of the plastic specimens. Water absorption was decreased by glyoxal treatment but was not affected by adipic/acetic anhydride treatment. Long-fiber (lf), short-fiber (sf), and microcrystalline (mc) cellulose were incorporated into soy isolate at various levels. Cellulose addition decreased the percentage elongation and increased the rigidity of the plastic. All three cellulose additions increased Young's modulus. The tensile strength increased with the addition of sf-cellulose to soy isolate; lf-cellulose decreased the tensile strength, whereas the incorporation of mc-cellulose did not have a significant effect. The yield strength increased slightly with the addition of sf-cellulose and was less affected by the addition of lf- or mc-cellulose. All three types of cellulose slightly decreased water absorption at ca. 15% content.Journal Paper No. J-15563 of the Iowa Agriculture and Home Economics Experiment Station, Ames; Project No. 2863.     

Synthesis of hydrogarnet from molten slag and its hydrogen chloride fixation performance at high temperature

Hydrogarnet was synthesized hydrothermally below 200°C using molten slag obtained from municipal solid waste. For comparison, it was also synthesized using pure-phase CaO–Al₂O₃–SiO₂–H₂O, as reported previously. The structural and textural properties of this material were investigated using various analytical and spectroscopic techniques such as X-ray diffraction, X-ray fluorescence spectrometry, atomic absorption spectrometry (AAS), thermogravimetry/differential thermal analysis, Fourier transform infrared spectroscopy, and scanning electron microscopy. The Cl⁻ fixation ability of hydrogarnet was investigated in the temperature range 500–800°C in a fixed-bed flow reactor using a HCl concentration (1000 p.p.m.v.) similar to that of incinerator exhaust gas. Under these experimental conditions, the hydrogarnet was capable of reducing the HCl gas level to less than 1 p.p.m.v. Analysis of the spent catalyst revealed that the hydrogarnet was being transformed into wadalite and CaCl₂ at high temperatures. The elution test for chromium ions in hydrogarnet obtained from slag was also used, and it was found that chromium ions were not eluted from hydrogarnet. Received: January 27, 2001 / Accepted: October 11, 2001     

Microwave-Assisted Solvent-Free or Aqueous-Based Synthesis of Biodegradable Polymers

Microwave radiation was used as the energy source for various types of chemical derivatizations of polysaccharides and for the synthesis of biodegradable polyesters in solvent-free or aqueous-based reaction systems. A medium to high degree of substitution was obtained for starch acetates, starch succinates, carboxymethyl konjac, aminated starch, and aminated chitosan. Ring-opening polymerization of lactide and -caprolactone proceeded rapidly even at low power output in the presence of tin octanoate catalyst. Complete monomer conversion and high molecular weight were achieved in less than 6 minutes under nonisothermal conditions. The yield rapidly increased with increasing power output and showed no significant change in a wide range of batch sizes. Polycaprolactone was successfully grafted from starch and konjac acetate in 3 minutes, yielding as high as 24% grafting efficiency and 25% grafting degree.     

基于风险的检验(RBI)在国内合成氨装置中的应用

利用API581基于风险的检验原理,采用RISKWISE分析软件对九江石化合成氨装置中的设备和管道进行了风险评估;并在装置采用的工艺、不同装置的设备和管道的失效机理和计算出的风险分布这3方面,将其风险评估结果与国内兄弟单位完成的其他合成氨装置的风险评估结果进行了比对;其结果体现了我国目前合成氨装置的设备和管道风险的大致分布,可供我国其他合成氨装置的风险评估参考,也为制定我国合成氨装置基于风险检验的法规标准提供了相关数据;同时,对国内采用针对装置的基于风险的检验的新模式进行了探讨。