过硫酸钾去除水中的TCE

以地水中的氯代烃污染物三氯乙烯(TCE)为目标污染物,以过硫酸钾溶液为氧化剂,探讨了不同条件下过硫酸钾对TCE的去除效果。实验结果表明,在40℃,过硫酸钾初始浓度为2.43 g/L条件下,反应2 h后,TCE的去除率就可达到96.8%;过硫酸钾对TCE的去除符合一级反应动力学方程,速率常数(K)为1.3364 h-1,半衰期(t1/2)为0.51 h;过硫酸钾对TCE的去除速率在pH为中性附近时最大,其后无论pH升高或降低去除速率均减小;受温度和pH影响较明显,并且反应温度越高,受pH的影响越明显;随离子强度的增加而减小;反应活化能为119.6 kJ/mol;过硫酸钾溶于水生成过硫酸根离子(S2O28-),S2O28-会进一步生成硫酸根自由基(SO4-.),在碱性条件下,SO4-.与OH-反应会进一步生成羟基自由基(.OH)。过硫酸钾对于TCE的去除主要源自SO4-.和.OH的强氧化性。     

常温低基质厌氧氨氧化反应器启动及其稳定性

以上向流生物滤池为反应器,以实验室内氧化沟回流污泥为接种污泥,采用先培育好氧生物膜,后转为厌氧环境培育厌氧氨氧化生物膜的方式,成功实现了常温低基质浓度下厌氧氨氧化反应器的启动。控制反应器进水pH为7.50～7.80,NH4+-N为30～40 mg/L,NO2--N为35～50 mg/L,温度为20～25℃。224 d以后,反应器启动成功。在稳定运行阶段,出水亚硝氮和氨氮的平均浓度分别为1.4 mg/L和4.6 mg/L,平均去除率分别为95.3%和90.1%,去除比例为1～1.8∶1,主要集中在1.4～1.5∶1,亚硝氮和氨氮去除的容积负荷分别为104.2 mg/(L.d)和146.0 mg/(L.d)。     

不同来源高浓度有机废水的集中处理

按照水质情况,将多种来源于不同工业生产过程中的高浓度有机废水划分为高悬浮固体乳化液废水、难生化高浓度有机废水、高悬浮固体不含油有机废水、含铬有机废水和杂质含量较少的乳化液废水5类,分别采用酸化破乳/Fen-ton氧化/混凝/絮凝、Fenton氧化/混凝/絮凝、混凝/絮凝、还原/混凝/絮凝、震动膜过滤技术作为生化预处理技术,并通过小试和中试验证了各技术的效果。实验结果表明,按照上述分类结果,采用不同预处理技术可以得到良好的效果,废水水质明显改善,满足继续生化处理的基本条件。各预处理生产装置处理效果稳定,同时生化系统已经稳定运行120天以上,COD去除率超过90%,出水经过低剂量的Fenton试剂处理后可达到《污水排入城镇下水道水质标准》(CJ343-2012)。     

Identification of key parameters controlling dissolved oxygen migration and attenuation in fractured crystalline rocks

In the crystalline rocks of the Canadian Shield, geochemical conditions are currently reducing at depths of 500-1000 m. However, during future glacial periods, altered hydrologic conditions could potentially result in enhanced recharge of glacial melt water containing a relatively high concentration of dissolved oxygen (O2). It is therefore of interest to investigate the physical and geochemical processes, including naturally-occurring redox reactions, that may control O2 ingress. In this study, the reactive transport code MIN3P is used in combination with 2k factorial analyses to identify the most important parameters controlling oxygen migration and attenuation in fractured crystalline rocks. Scenarios considered are based on simplified conceptual models that include a single vertical fracture, or a fracture zone, contained within a rock matrix that extends from the ground surface to a depth of 500 m. Consistent with field observations, Fe(II)-bearing minerals are present in the fractures (i.e. chlorite) and the rock matrix (biotite and small quantities of pyrite). For the parameter ranges investigated, results indicate that for the single fracture case, the most influential factors controlling dissolved O2 ingress are flow velocity in the fracture, fracture aperture, and the biotite reaction rate in the rock matrix. The most important parameters for the fracture zone simulations are flow velocity in the individual fractures, pO2 in the recharge water, biotite reaction rate, and to a lesser degree the abundance and reactivity of chlorite in the fracture zone, and the fracture zone width. These parameters should therefore receive increased consideration during site characterization, and in the formulation of site-specific models intended to predict O2 behavior in crystalline rocks.     

预测有机化合物对水蚤EC50值的片段常数法

根据217种化合物建立了估算有机化合物对水蚤EC50值（48h半数影响浓度）的片段常数模型,分析了模型的误差及稳健性。研究结果表明,有机化合物的片段常数和结构因子与水蚤的EC50值倒数的对数（lg1/EC50)显著相关,可以根据片段常数法估算有机化合物对水蚤的EC50。模型的可决系数为0.9687,平均绝对误差0.40个对数单位,其中68.7%化合物的误差小于0.5个对数单位。     

趋势分析法评价苯系物标准气体的时间稳定性

根据GB/T 15000.3—2008设计了苯系物标准气体的时间稳定性研究方案,制备了4瓶苯系物标准气体,随着时间的推移进行测定并将结果制图,结果显示量值随时间没有显著的变化趋势。以线性关系为模型,计算线性直线的斜率和斜率的标准偏差,用t检验判断斜率是否显著来评价标准气体的稳定性。计算结果显示,所有斜率均不显著,因此该研究制备的苯系物标准气体能够稳定保存22个月。根据时间稳定性数据计算由不稳定性引起的不确定度,并讨论了这种计算不稳定性引起不确定度的方法对结果有放大的可能性。     

环境监测用5种氯代烯烃混合气体标准样品研制

介绍了1μmol/mol氮气中5种氯代烯气体标准样品的研制方法。这5种氯代烯包括氯乙烯、1,1-二氯乙烯、顺1,2-二氯乙烯、三氯乙烯、四氯乙烯,其中氯乙烯常温下为气态,其他4种为液态,并且沸点低,将这几种氯代烯制备成气体标准样品存在制备精度低、气液转换不完全等困难。经研究,采用2步称量法制备5种氯代烯气体标准样品,重复制备的相对标准偏差小于1.6%。建立了5种氯代烯标准气体瓶内均匀性的实验方法,并通过考察样品量值伴随样品压力的变化来评价样品的均匀性。结果显示,5种氯代烯标准气体是均匀的,最低使用压力为1 MPa。依照ISO 15000.3来考察样品的时间稳定性,样品有效期为12个月。相对扩展不确定度为3%(置信度为95%)。     

关于植物中氟化物测定结果的计算

针对植物中氟化物测定时由于绘制校准曲线的标准溶液体积与分析样品的定容体积不一样而引出的结果计算时的某些问题,提出了正确的计算方法和建议。     

Comparison of criteria for prediction of runaway reactions in the sulphuric acid catalyzed esterification of acetic anhydride and methanol

Loss of temperature control is one of the major reasons that can lead to runaway reaction. This occurrence is commonly named thermal runway. The aim of this paper is the application of thermal runaway criteria in order to predict the onset of runaway phenomena and define the range of stability related to operating conditions in the reactor, with specific reference to the esterification of acetic anhydride and methanol catalysed by sulphuric acid tested in isoperibolic conditions. The isoperibolic calorimeter has also been used to obtain thermodynamic, kinetic and physical chemistry data necessary to develop a model for the reaction. Some runaway criteria applied in this work require a model for the process, so a model for the analyzed system been developed.Because of the modest reaction enthalpy and low activation energy this reacting system provide a severe test to the runaway criteria.In this work, various runaway criteria have been applied to the experimental and simulated data and the results obtained have been compared.     

Photodegradation of sulfonamide antibiotics in simulated and natural sunlight: Implications for their environmental fate

The photochemical fate of seven sulfonamides was investigated in matrices representative of natural water bodies under various light sources. Fundamental photolysis parameters such as molar absorption coefficient, quantum yield (QY) and first-order rate constants were determined. The photolysis decay rate was dependent on the protonation state of the molecule, pH of the water sample and dissolved organic matter. Natural organic matter was the most significant factor in the indirect photolysis of sulfonamides. Half-lives were in the range of minutes at 254 nm to days under natural sunlight. Under natural sunlight, all sulfonamides showed higher removal rates in natural waters implying that indirect photolysis is the predominant mechanism.