前置反硝化生物滤池深度脱氮效能与影响因素

前置反硝化生物滤池具有良好的脱氮性能,被广泛用于污水的深度处理。采用该工艺对城市污水处理厂尾水进行深度处理,通过调节硝化液回流比（50%、100%、150%）和水力负荷（1.0、1.5和2.0 m3·（m2·h）-1）,考察前置反硝化生物滤池工艺对COD、TN、NH4+-N的去除效果。结果表明,当硝化液回流比为100%时,系统对污染物去除效果最好。在进水COD、TN、NH4+-N平均浓度为120、35和15 mg·L-1的水质条件下,出水COD、TN、NH4+-N平均浓度可降到7.62、5.02和0.60 mg·L-1,去除率分别为93.65%、85.65%和96.00%。在水力负荷为1.5 m3·（m2·h）-1条件下,系统对COD、TN和NH4+-N的平均去除率达到了83.00%、90.14%和95.73%,出水可以达到《城镇污水处理厂污染物排放标准》（GB 18918-2002）一级A标准。     

不同菌种组合对发酵残余物好氧堆肥进程及氮素变化的影响

适宜菌剂组合对于初始电导率（Electronic conductivity,EC）较高的发酵残余物二次干化腐熟效果具有重要影响。通过在发酵残余物（猪场沼渣、城市生活污泥）好氧发酵过程中添加不同菌种组合,研究堆肥腐熟指标变化,特别是不同形态氮素指标变化,以期更好提升发酵残余物的干化和腐熟程度。结果表明：F3菌剂组合处理高温期达16 d,最高温度为69.5℃,最早进入腐熟阶段,全氮损失比例最少,为8.72%;对照组在高温期（14 d、69.3℃）及全氮损失比例（9.21%）指标上仅低于F3处理组,表明自然堆体存在耐盐菌种;在促进堆肥腐熟效果方面,霉菌起着关键的作用,堆肥后期酵母菌的存在促进堆体腐熟度的提升;菌种比例和种类的合理设置对于堆体腐熟度提高的重要性要高于活菌添加量;在堆肥保氮过程中,真菌（霉菌和酵母菌）起着重要作用。F3处理（即芽孢杆菌：霉菌：酵母菌=1：2：2）,是实现发酵残余物快速高效堆肥的理想菌剂配方,其他复配菌种组合保氮效果改良侧重点各不相同。     

反胶束漆酶/纤维素酶体系中油酸酯化的优化

漆酶和纤维素酶在反胶束水核中心具有较强的催化活性。为了对反胶束酶体系中油酸酯化反应深入研究,采用生物表面活性剂鼠李糖脂构建反胶束体系作为漆酶与纤维素酶酯化油酸的催化反应场所。通过实验研究了反胶束体系的不同条件对酯化产物含量的影响。对于反胶束漆酶体系,最佳酯化条件为：含水量W0 40%,鼠李糖脂临界胶束浓度20 mmol·L-1,pH值4,温度40 ℃;对于反胶束纤维素酶体系,最佳酯化条件为：含水量20%,鼠李糖脂临界胶束浓度80 mmol·L-1,pH值4,温度30 ℃。综合考虑几个因素,漆酶比纤维素酶更适合应用于反胶束中油酸的酯化。研究同时采用荧光光谱法对漆酶和纤维素酶在反胶束体系中结构性能的变化进行研究,结果表明,当反胶束体系处于最佳酯化反应条件时,荧光强度最高。     

分子生物技术在环境工程微生物领域中的应用

目前分子生物技术发展日新月异,已渗透到各相关学科。本文综述了分子生物技术的基本原理与方法,及其在环境工程微生物领域的应用。讨论了分子生物技术在环境工程微生物的检测应用及在污泥、生物膜、底泥和土壤等微生物种群的多样性分析方面,以及环境工程菌的挑选和培养等方面的研究成果及其巨大研究前景,对该技术在环境工程领域的应用与发展提出了一些见解。     

气-水联合反冲洗膜污染防治技术研究

采用气水联合反冲洗技术,考察了气水比(Qg/Ql)、反冲洗周期及其对膜污染的防治效果。结果表明,气水联合反冲洗较单独气或水反冲洗效果好;在过滤周期20min,反冲洗时间1min,气水比1.5时,气水联合反冲洗能够恢复膜通量到膜清水通量的80%以上。此法可大幅度清除沉积在膜表面的泥饼层,恢复膜通量,维持膜过滤性能的稳定,是一种较为有效的膜污染防治技术。     

Surface Consolidation of Pentelic Marble: Criteria for the selection of methods and materials - The Acropolis case (6 pp)

Goal and Scope In order to realize surface consolidation of Pentelic marble on the Acropolis monuments, we have collected the criteria that have to be fulfilled by the methods and materials without side effects on the marbles (and other stones). When the existing methods and materials did not satisfy the requirements (criteria), we invented new ones.Methods The criteria were collected from the literature, by thermodynamic and kinetic viewpoints, by laboratory experiments and in situ observations on monuments, both in Greece and in several countries in which the various methods and materials were applied. Concerning our method of ‘Inversion of sulfation’, performed by spraying a K2CO3 solution, its concentration and its temperature were controlled in order to have a total inversion (certified by liquid crystals) of gypsum back to CaCO3. For the new material of ours, ‘Reinforced Lime’, in order to eliminate the disadvantages of plain lime (low carbonation rate, low mechanical properties of CaCO3 formed, lack of carbonation in the bulk of lime), measurements of the rate of carbonation were performed in plain lime and in lime with a different CaCO3 concentration beforehand as well as in a different CO2 environments, using DTG and XRD to measure the rate of carbonation. The detachment (kg/cm2) of marble specimens stuck by lime in each case was also measured. A microscope was also used to measure the dimensions of the grain in each case as well as ammonium citrate and thymolphthalein to certify the depth of carbonation in each case. Part of the work was communicated in an international congress.Results A table with the criteria of the selection of the methods and materials for the consolidation of Pentelic marble surfaces (and other stones) was established. None of the employed methods and materials fulfilled the criteria. Only the ‘Inversion of gypsum ‘ and the ‘Reinforced Lime’ were adopted and applied to the Acropolis monuments and to other monuments in Greece and in several other countries.Recommendation and Outlook All criteria must be used for the selection of methods and materials for the consolidation of the monument surfaces. This is why we have already studied with the same procedures, methods and materials for restoration, surface cleaning and protection.     

焦炉装煤烟尘治理方案的探讨

焦炉装煤烟尘含有害物质，污染环境，危害人体健康。袋式除尘器的使用，消除了烟尘的污染，但因投资大、运行费用高、操作复杂，难以得到快速、广泛的推广。根据实验结果和已有应用情况，本文推荐了三相流化床除尘装置和颗粒层除尘器，它们可用于焦炉装煤烟尘治理，其投资和运行费用会大大降低。     

宁波市城市污水处理厂污泥处置方案探讨

随着城市污水处理率提高导致的污水污泥产量的增长趋势也使得污水污泥的处理问题更为突出。在总结国内外城市污泥处置技术发展趋势的基础上,结合宁波市的实际情况,根据无害化、减量化和资源化的原则,提出城市污泥近远期处置方案,并对处置方案作出可行性分析。     

氧化亚铁硫杆菌对亚铁离子的氧化及其动力学研究

采用9K培养基研究了氧化亚铁硫杆菌氧化Fe^2＋过程中,pH和氧化还原电位的变化规律,并对Fe^2＋的氧化过程进行动力学分析,确定了其反应级数及反应速率常数。结果表明,（1）在温度为30℃,摇床转速为150r／min的条件下,氧化亚铁硫杆菌的最佳接种量为10．0％;（2）Fe^2＋初始质量浓度在11．39～21．72g／L时,随着浓度的增大,Fe^2＋达到100％转化率需要的时间增加;（3）氧化亚铁硫杆菌对Fe^2＋的氧化可近似看作一级反应,反应速率常数为0．0527～0．0788h。     

Inhibiting effects by Fe2O3 on combustion and explosion characteristics of ABS resin

The global increase in the use of, and reliance on, plastics has prompted the demand for acrylonitrile-butadiene-styrene (ABS) resin in various fields. With this increased requirement, numerous failures have occurred in the ABS process. Those incidents, resulting from electrostatic discharge, powder accumulation, heat accumulation, construction sparks, and plant fires, have caused dust fire and explosions.In this study, the ABS resin was gleaned from the site and tested for its explosion parameters, including minimum ignition temperature of dust cloud (MIT_C), minimum ignition energy (MIE), and minimum explosion concentration (MEC). To improve loss prevention in the manufacturing process, ferric oxide (Fe₂O₃) as an inert additive was added in the ABS powder. According to the MIE test, Fe₂O₃ has an apparent inhibiting effect on dust explosion for the ABS dust. With the proportion of Fe₂O₃ increased from 25 to 50 mass% in ABS, the MIE increased from 67 to 540 mJ. The explosion tests via 20-L apparatus indicated that Fe₂O₃ mixed with ABS could not increase the MEC significantly. However, the explosion pressure dropped by increasing in the ratio of Fe₂O₃ in ABS. This inerting strategy of ABS was deemed to substantially lessen the probability and severity of fire and explosion.