五种重金属在小麦植株不同器官中的分布特征

为研究Cd、Pb、As、Cu、Zn等5种重金属在小麦植株不同器官的分布特征，以郑州9023为供试品种，采用田间试验方法，应用原子吸收分光光度法和电感耦合等离子体原子发射光谱法(ICPS)分别测定了小麦植株不同器官的重金属质量分数并进行了分析。结果表明，小麦植株中较易富集Cd的器官是根、叶及废弃物，较易富集Pd、As的器官是根、茎及废弃物，较易富集Zn、Cu的器官是根、茎和籽粒；在这5种重金属中，Zn在小麦茎和籽粒中的富集系数最高，Cd在地上部分其他器官的富集系数最高，而Pb在这些器官中富集系数均为最低，Cu和As则居中。     

多泥沙河流水质模型研究

针对黄河泥沙含量大、泥沙对河流CODMn浓度影响大的突出特点,运用模拟实验方法,探讨了泥沙对CODMn浓度的影响,揭示了浑水、清水中CODMn浓度与含沙量间的关系.研究表明,黄河浑水中CODMn浓度随含沙量增大呈显著上升趋势,而去除泥沙后清水CODMn浓度测定值随其原含沙量增大呈微上升趋势.依据质量平衡原理,建立了充分考虑泥沙影响的CODMn衰减经验模型.清水中CODMn浓度的变化采用完全混合反应器概念来模拟,浑水中CODMn浓度通过清水中CODMn浓度与泥沙中CODMn浓度之和来量化.模型基本方程的求解采用稳态解析解.模型中的参数通过利用实际监测数据及室内实验结果与优化结合的方法确定.同时,利用实际监测数据对参数和模型进行检验.结果表明,模型结构合理,参数取值可靠,模型精度较好.模型既能揭示汇流区间人为污染对河段水质的影响,又可以反映作为面污染源的黄河泥沙对污染的影响,可作为水质预测的实用工具及规划管理的依据.     

土介质炸点痕迹反演爆源特征的研究

论述了土介质炸点痕迹特征参量及其控制影响因素,通过对国内外现有研究成果的再分析和有效利用,得到爆源特征与炸点痕迹特征参量之间的关系。在此基础上,建立利用土介质上的炸点痕迹反演爆源特征的方法,并实现编程计算。通过实例分析说明了该方法的可行性。     

云南个旧多金属矿区农田土壤-作物系统重金属污染现状——以乍甸镇为例

对云南个旧市乍甸镇农田土壤和农作物重金属污染现状进行了野外调查及评价。结果表明:农田土壤Pb、Zn、Cu、Cd、As质量比均超出GB 15618—1995《土壤环境质量标准》二级标准,Hg未检出,该地区农田呈现以As、Cd为主多种重金属复合污染。Pb、Zn、Cu、Cd、As土壤有效态质量比与土壤全量呈极显著正相关(p<0.01)。农作物中Cu、As质量比与土壤有效态Cu、As质量比无显著相关,Zn质量比与土壤有效态Zn呈极显著负相关(p<0.01),Cd、Pb质量比与土壤有效态Cd、Pb呈显著正相关(p<0.05)。89%的农作物As超标,油菜籽(Brassica napusL.)As质量比最高,均值达(23.04±14.33)mg/kg(鲜重,下同)。Pb超标率达72%,油菜籽Pb质量比最高,平均为(5.55±2.53)mg/kg。Zn、Cd超标率均为11.11%,超标最严重的油菜籽Zn质量比为(46.65±13.61)mg/kg,Cd质量比为(0.24±0.10)mg/kg。Cu超标率为5.55%,油菜籽Cu质量比最高,达(16.02±2.75)mg/kg。油菜籽对As、Pb、Zn、Cu、Cd的转移系数(农作物可食部分重金属质量比(鲜重)与土壤重金属质量比的比值)远高于其他作物。农作物对Pb、Zn、Cd、As的转移顺序依次为果实类、叶菜类、根茎类,对Cu的转移顺序为果实类、根茎类、叶菜类。农作物以As、Pb污染为主,总体属重度污染。聚类分析得出:油菜籽、青蒜(Allium ampeloprasumL.)和生菜(Lactuca sativaL.var.ramosaHort.)重金属污染严重,不适合在该地区继续种植和食用。     

不同物质对铬价态测定结果的影响

采用单波长法和双波长法,分别考察了KH2PO4、H3PO4、H2SO4、KNO3、牛肉膏和蛋白胨对Cr(III)和Cr(VI)质量浓度测定的影响。结果显示,Cr(III)和Cr(VI)在测量中是相互影响的,并且Cr(III)对Cr(VI)影响较显著。在单波长法测定中,牛肉膏、蛋白胨及2种酸对Cr(III)和Cr(VI)的影响较钾盐对其影响更为显著,H3PO4和H2SO4对Cr(III)和Cr(VI)的特征吸收峰值影响最大,降低幅度在20%～50%。这些物质对双波长法测定Cr(VI)几乎没有影响;但对Cr(III)测定中,H2SO4和H3PO4的影响较大,其相对误差分别为14.57%和8.87%,其余物质产生的相对误差均小于1.6%。因此,双波长法可用于生物样品中Cr(III)和Cr(VI)的测定,线性范围分别为0～160 mg/L和0～80mg/L。     

村镇生活垃圾重金属含量及其来源分析

对全国12个省份72个典型村镇的生活垃圾进行采样调查,系统分析我国村镇生活垃圾中重金属污染特征及其可能来源.结果表明,我国北方典型村镇生活垃圾中重金属As、Hg、Pb、Cd、Cr、Cu、Zn和Ni的含量分别为(7.51±8.89)、(0.64±0.42)、(21.91±12.29)、(4.82±8.37)、(86.36±59.99)、(36.43±15.98)、(62.19±36.61)和(46.07±25.22)mg·kg-1,南方典型村镇生活垃圾中重金属As、Hg、Pb、Cd、Cr、Cu、Zn和Ni的含量分别为(7.43±8.82)、(0.83±0.74)、(21.62±13.76)、(1.84±4.55)、(131.06±74.96)、(37.20±16.80)、(98.04±63.71)和(46.75±25.75)mg·kg-1.与《城镇垃圾农用控制标准》(GB 8172-87)和《土壤环境质量标准》(GB 15618-1995)二级标准相比,重金属Cd和Hg超标较严重.通过聚类分析、Pearson相关分析和主成分分析解析垃圾中重金属污染物的来源,结果表明我国典型村镇生活垃圾中Pb和Cd主要来源于厨余、灰土、橡塑类和纸质等印刷品,Hg主要来源于厨余和灰土,Zn和Cr主要来源于灰土,Cu主要来源于电子、电池类废弃物和尘土、橡塑、纸质等印刷品,Ni主要来源于废弃的电子、电池类产品,As主要来源于杀虫剂等农药和肥料.     

Electrocoagulation process for the treatment of metal-plating wastewater: Kinetic modeling and energy consumption

The wastewater from industrial area was treated by EC via Fe and Al electrodes. Cu, Ni, Cr and Zn were highly removed at the first minutes, simultaneously. Pseudo-2nd-order was found to be more suitable for kinetics. Adsorption capacities based on kinetic modeling were observed as Cr>Cu>Ni>Zn. The chemical cost in the case of pH adjustment after EC was less as 3.83 $/m³. It is known that wastewater produced by the metal-plating industry contains several heavy metals, which are acidic in nature and therefore toxic for the environment and for living creatures. In particular, heavy metals enter the food chain and accumulate in vital organs and cause serious illness. The precipitation of these metals is mostly achieved by pH adjustment, but as an alternative to this method, the electrocoagulation process has investigated in this study using iron and aluminum electrodes. The effects of the pH adjustment on removal before and after the electrocoagulation process were investigated, and cost analyses were also compared. It was observed that a high proportion of removal was obtained during the first minutes of the electrocoagulation process; thus, the current density did not have a great effect. In addition, the pH adjustment after the electrocoagulation process using iron electrodes, which are 10% more effective than aluminum electrodes, was found to be much more efficient than before the electrocoagulation process. In the process where kinetic modeling was applied, it was observed that the heavy metal removal mechanism was not solely due to the collapse of heavy metals at high pH values, and with this modeling, it was seen that this mechanism involved adsorption by iron and aluminum hydroxides formed during the electrocoagulation process. When comparing the ability of heavy metals to be adsorbed, the sequence was observed to be Cr>Cu>Ni>Zn, respectively.     

Electro-remediation of tailings from a multi-metal sulphide mine: comparing removal efficiencies of Pb,Zn, Cu and Cd

Sulphidic mine tailings characterised by high concentrations of heavy metals (Pb 3532?±?97?mg/kg, Zn 8450?±?154?mg/kg, Cu 239?±?18?mg/kg and Cd 14.1?±?0.3?mg/kg) and abundant carbonate (17%) were subjected to eight lab-scale electrodialytic remediation (EDR) experiments to investigate the influence of current density, treatment time and particle size on removal efficiency. Pb and Cu removal improved when increasing current density, while Zn and Cd removal did not. In contrast Zn and Cd removal improved by grinding the tailings, while Pb and Cu removal did not. At the highest current density (1.2?mA/cm²), 94%, 75%, 71% and 67% removal of Pb, Zn, Cu and Cd could be achieved, respectively, on grinded tailings in 28 days. Sequential chemical extraction made before and after EDR revealed larger oxidisable fractions of Zn, Cu and Cd, representing large fractions of sulphides, which was likely to be the main barrier to be removed as efficiently as Pb. This was in accordance with acid/base extraction tests in which Pb showed high solubility at both high and low pH (up to 65% and 86% of extraction, respectively), while considerable extraction of Zn (55%) happened only at low pH; and very limited extraction (<20%) of Cu and Cd occurred at any pH.     

红壤和磷灰石对沉积物重金属稳定化的影响

利用磷灰石、红壤及两者复配组合对污染沉积物中重金属进行稳定化处理,通过TCLP和改进的BCR连续提取法对稳定化效果进行分析和评价。结果表明,在稳定化试验中,对Cu、Cd和Zn的稳定效果由大到小为红壤+磷灰石、磷灰石、红壤;其中,红壤+磷灰石对Pb的稳定效果与磷灰石单独添加相近,显著大于红壤。5%磷灰石+5%红壤添加3个月后,Cu、Cd、Zn和Pb的稳定效率分别达到59.83%、29.43%、31.00%、96.06%。添加5%磷灰石时,Cu、Cd、Zn和Pb的稳定效率分别为52.46%、24.67%、25.23%、96.06%。红壤的添加不同程度地促进了磷灰石对Cu、Cd和Zn的稳定效率。连续提取试验结果表明.磷灰石单独和复配添加均使Cu、Zn和Pb的生物可利用态和潜在生物可利用态占比降低,生物不可利用态占比增大。5%磷灰石+5%红壤处理中,Cu、Cd、Zn和Ph的生物可利用态和潜在生物可利用态的比例总和分别降低了19.31%、5.11%、20.11%和68.97%。相比磷灰石单独处理,复配处理进一步促进了Cd和Zn的酸溶态向残渣态转化。磷灰石和红壤+磷灰石复配处理能有效降低沉积物中重金属的危害。     

不同来源重金属在土壤中的形态分布差异

试验表明：不同来源的Ｐｂ、Ｚｎ和Ｃｄ复合污染物在土壤中的形态分布有明显的差异，在废矿水和尾矿砂污染的土壤中，Ｐｂ、Ｚｎ和Ｃｄ主要以残渣态存在，而添加土壤中的Ｐｂ主要以弱专性吸附态和有机结合态存在，Ｚｎ和Ｃｄ主要以交换态存在，大豆苗对添加土壤中Ｐｂ、Ｚｎ和Ｃｄ的富集能力较强，而对废矿水污染和尾矿砂污染土壤中Ｐｂ、Ｚｎ和Ｃｄ的富集能力相对较弱。