碳酸镁与镉离子的吸附和沉淀作用研究

以碳酸镁为吸附剂,在镉离子初始浓度为0~6 mmol/L,初始pH值为4和7的条件下,研究了碳酸镁与镉离子的吸附与沉淀作用。结果表明,由于碳酸镁的溶解及与体系中氢离子的中和,碳酸镁—镉体系的最终pH值为10.4左右;体系的平衡pH值随着镉离子初始浓度的增加而减小;体系中镉的平衡浓度随着初始镉离子浓度的增加缓慢上升;碳酸镁对镉的吸附等温线为折线型,不符合Freundlich和Langmuir模型,符合伪二阶吸附动力学模型。结合碳酸镁吸附镉前后固相表征的结果,说明碳酸镁与镉离子的作用机制随着镉离子浓度的增加,从离子交换发展为离子交换和表面配位反应并存,最后表现为表面沉淀。     

Detection of Class I and II integrons for the assessment of antibiotic and multidrug resistance among Escherichia coli isolates from agricultural irrigation waters in Bulacan,Philippines

Contaminated irrigation water may greatly affect not only the quality of produce but also the people exposed to it. In this study, agricultural irrigation waters in Bulacan, Philippines were assessed and found to be contaminated with Escherichia coli (E. coli) ranging from 0.58 to 4.51 log₁₀ CFU/mL. A total of 79 isolates of E. coli were confirmed through polymerase chain reaction (PCR) amplifying the uidA gene and were tested for phenotypic resistance using 10 antimicrobials through the Kirby–Bauer disc diffusion method. Forty-six isolates (58.22%) were noted to be multidrug resistant (MDR) with high resistance rate to cephalothin, tetracycline, streptomycin, ampicillin, trimethoprim, nalidixic acid, and chloramphenicol. Moreover, this study also examined the prevalence of Class I and II integrons accounting to 67.39% and 17.39%, respectively, of the MDR E. coli strains using multiplex PCR. The results imply that the agricultural water used in Bulacan is contaminated with the fecal material of man or other animals present in the area, and the presence of MDR bacteria, which pose a potential threat to individuals in these areas, is alarming. In addition, detection of integrons could be a good marker for the identification of MDR isolates. Lastly, this study could develop strategies for the proper management of farming sites leading to the detection of food-borne pathogens and prevention of infectious diseases.     

臭氧氧化法处理焦化废水生化出水的反应动力学

对臭氧氧化去除焦化废水生化出水COD的反应动力学及其影响因素进行了实验研究,结果表明,在臭氧投加量为8．50mg／min,反应温度为20＇E和初始pH为10．61条件下,对COD的降解符合表观一级反应动力学模型,其相关系数R。=0．9991,表观反应速率常数k。。=1．01×10^-3s-1。该条件下,臭氧氧化对COD的降解主要来源于高活性羟基自由基的强氧化作用。在不同的臭氧投加量（4．25～12．75mg／min）、不同的反应温度（10～40℃）和不同的初始pH（3．76～12．53）下,COD的降解也同样遵循一级反应动力学规律。随着臭氧投加量的增大,COD降解的表观反应速率常数从（0．554×10^-3）s-1增加到（1．06×10＆-3）s-1;随着反应温度的升高,表观反应速率常数从（0．427×10^-3）s-1增加到（1．40×10-3）s-1,温度越高反应速率提高的幅度却越小;在初始pH3．76～10．61范围内,表观反应速率常数从（0．218×10^-3）s-1增加到（1．01×10^-3）s-1,在初始pH为12．53时表观反应速率常数下降到（0．857×10^-3）s-1。     

臭氧氧化法处理焦化废水生化出水的反应动力学简

对臭氧氧化去除焦化废水生化出水COD的反应动力学及其影响因素进行了实验研究,结果表明,在臭氧投加量为8.50 mg/min,反应温度为20℃和初始pH为10.61条件下,对COD的降解符合表观一级反应动力学模型,其相关系数R²=0.9991,表观反应速率常数k_Abs=1.01×10^-3 s^-1。该条件下,臭氧氧化对COD的降解主要来源于高活性羟基自由基的强氧化作用。在不同的臭氧投加量（4.25~12.75 mg/min）、不同的反应温度（10~40℃）和不同的初始pH（3.76~12.53）下,COD的降解也同样遵循一级反应动力学规律。随着臭氧投加量的增大,COD降解的表观反应速率常数从（0.554×10^-3） s^-1增加到（1.06×10^-3） s^-1;随着反应温度的升高,表观反应速率常数从（0.427×10^-3） s^-1增加到（1.40×10^-3） s^-1,温度越高反应速率提高的幅度却越小;在初始pH3.76~10.61范围内,表观反应速率常数从（0.218×10^-3） s^-1增加到（1.01×10^-3） s^-1,在初始pH为12.53时表观反应速率常数下降到（0.857×10^-3） s^-1。     

Fenton法处理垃圾渗滤液的参数优化及反应动力学模型

采用Fenton法处理垃圾渗滤液,研究反应时间、初始浓度、pH、Fenton试剂用量对垃圾渗滤液TOC去除率的影响。研究结果表明,最优反应条件是反应时间30 min,初始pH为3.0,初始[H2O2]0=7 310 mg/L,最佳[H2O2]/[Fe2+]摩尔比为5,反应温度为室温,此时渗滤液的TOC去除率达到70.3%。渗滤液矿化过程符合一级反应动力学,并建立了符合该渗滤液的反应动力学模型。     

反应气耦合等离子体降解沙林模拟剂

采用水蒸气、氨气、过氧化氢气雾和臭氧4种气体对沙林模拟剂氟磷酸二异丙酯(DFP)进行降解研究,发现臭氧对DFP具有较好的降解作用,在流量200 L/h,DFP初始浓度50 mg/m3时,降解率最高可达56.1%。对高浓度DFP(大于80 mg/m3)进行降解研究时,等离子体单独作用最高降解率为89%,而添加臭氧后的降解率都在95%以上。计算得到臭氧作用的能量利用率为0.05 mg/(W·h),等离子体的能量利用率为0.55 mg/(W·h),而添加臭氧后的等离子体能量利用率为0.68 mg/(W·h)明显高于臭氧和等离子体能量利用率之和,因此对高浓度DFP进行处理时,臭氧与等离子体存在耦合作用。对等离子体和臭氧耦合等离子体降解DFP反应进行了产物分析,发现主要的降解产物基本一致,但是臭氧的存在能使降解更加彻底。     

稠油污水回用锅炉处理工艺的应用

新疆油田公司稠油污水处理普遍采用成熟的离子调整旋流反应水处理技术,污水处理后达到回用锅炉水质标准SY/T 0097-2000《稠油油田采出水用于蒸汽发生器给水处理设计规范》,供给油田专用高压注汽锅炉用水。采用相同技术建成的采油一厂稠油处理站污水回用锅炉处理工艺投用后,处理后污水回用锅炉,减少了含油污水的外排,充分利用了稠油污水的热能,取得了良好的经济和社会效益。     

Desorption of polycyclic aromatic hydrocarbons from field-contaminated soil to a two-dimensional hydrophobic surface before and after bioremediation

This study investigated environmental distributions and production mechanisms of chlorinated polycyclic aromatic hydrocarbons (Cl-PAHs) in the sediments from some tidal flats located in Asia. Cl-PAHs were found in sediments taken from Arao tidal flat, Kikuchigawa River and Shirakawa River. The range of ∑Cl-PAHs was from 25.5 to 483 pg g⁻¹ for Kikuchigawa River and Arao tidal flat, respectively.Concentrations of PAHs and Cl-PAHs showed no significant correlations (r = 0.134). This result suggests that the origins of these compounds differ. In the identified Cl-PAH isomers, the most abundant Cl-PAH isomer was 9,10-dichloroanthracene (9,10-di-Cl-ANT) in the three sites. In general, concentrations of Cl-ANTs in the coastal environment are about 3-5 orders of magnitude lower than those of anthracene (ANT). However, concentration ratios between Cl-ANTs and ANT (Cl-ANTs/ANT) in the sediments ranged from 4.1% to 24.6%. This result indicated that Cl-PAHs were not generated under industrial processes but the high concentration ratios have resulted from the contribution of photochemical production of Cl-ANTs in the sediments because ANT is known to have high photochemical reactivity.For examining this phenomenon, ANT adsorbed onto glass beads was irradiated with UV under the mimicked field conditions of tidal flats. As a result, it was noticed that, while chlorinated derivatives were negligible in a light-controlled group, production of 2-Cl-ANT, 9-Cl-ANT and 9,10-diCl-ANT on the irradiated surface were found in this study. These results suggest that photochemical reaction of PAHs can be a potential source of the occurrence of Cl-PAHs in the coastal environment.     

Fe2O3-Cr2O3/TiO2系列催化剂的结构和脱硝性能

研究以纳米TiO2为载体,浸渍负载过渡金属氧化物,以CO为还原剂的脱硝催化剂的脱硝性能。实验中以计算量的Ni(NO3)2和Fe(NO3)3混合溶液浸渍纳米TiO2粉末,室温下搅拌30 min至混合均匀,放入旋转蒸发器中,70℃下至水分蒸干为止;所得粉末在550℃下、空气气氛中焙烧4 h即得所需催化剂。用以上方法分别制备2%Fe2O3-10%Cr2O3/TiO2、4%Fe2O3-8%Cr2O3/TiO2、6%Fe2O3-6%Cr2O3/TiO2、8%Fe2O3-4%Cr2O3/TiO2与10%Fe2O3-2%Cr2O3/TiO2等5种催化剂样品。实验结果表明,制备的催化剂具有较好的结构,分散较为均匀。对于CO+NO反应,Fe2O3-Cr2O3/TiO2系列催化剂具有较好的催化活性,NO的转化率都达到了100%。其中,10%Fe2O3-2%Cr2O3/TiO2样品具有最好的低温活性,H2-TPR结果表明,这是由于10%Fe2O3-2%Cr2O3/TiO2催化剂更易于被CO预还原。     

微波诱导AC/Cu、AC/Fe催化非均相Fenton 反应催化降解垃圾渗滤液

采用活性炭载体负载Cu、Fe为催化剂,在微波诱导作用下,对垃圾渗滤液污染物进行降解。实验结果表明,活性炭负载金属前经适当浓度硝酸浸泡处理后,催化剂对COD去除率提高可超过15%,过高硝酸盐浓度对COD去除有不利影响;催化剂对COD去除率随Cu、Fe金属负载量增加呈先增加后降低的趋势,催化剂对Cu、Fe的最佳负载量分别为质量百分比2.11%和1.12%。对于AC-Cu体系,在初始pH=3,H2O2投加量为4.98×103mg/L,催化剂用量为5.0×103mg/L,420 W功率下微波辐射10 min时,垃圾渗滤液COD去除率可达到84.13%;对于AC-Fe体系,当H2O2投加量为0.33×103mg/L,催化剂AC-Fe用量为2.0×104mg/L,420 W功率下微波作用10 min时,垃圾渗滤液COD去除率为60.16%。分析2种催化剂对COD去除差异的原因,可能是催化剂AC-Cu表面单分子分布的阈值比AC-Fe高。降解液的pH值对AC-Cu体系、AC-Fe体系COD去除影响存在拐点,最高COD去除率点对应的降解液pH值为3。微波辐射功率较低时,体系COD去除率随辐射功率增加而增加;辐射功率较高时,高温下垃圾渗滤液中有机硫化物分解成小分子硫化物,对催化剂活性存在一定抑制作用。