基于速度的交通事故分析

速度对交通事故的发生以及严重程度有着直接影响,是道路交通事故的重要诱因之一。为了准确地反映速度与事故之间的关系,减轻由于速度因素所造成的交通事故的损失,笔者对国内外速度与交通安全的情况进行分析;研究了平均速度与事故危险性、速度离散度与事故率以及速度与事故严重性的关系;提出了加强速度管理,控制交通流平均速度和减小相邻路段的速度差值的对策。基于速度的交通事故分析,建议采用85%位车速作为控制速度的上限值;提出限速措施,以达到减少交通事故及其损失的目的。     

某型机车牵引电机传动端轴承低速轻载无飞溅润滑试验研究

主要根据客户要求,在低速(1 km/h)及轻载工况下,测量传动端轴承无飞溅润滑条件下的温升等参数,而进行相关的电机试验,为某型机车牵引电机传动端轴承在低速及轻载工况下,无飞溅润滑提供试验验证及技术支撑。     

Assessment of the clear-sky bias issue using continuous PM10 data from two AERONET sites in Korea

A bias in clear-sky conditions that will be involved in estimating particulate matter(PM)concentration from aerosol optical depth(AOD) was examined using PM_(10) from two Aerosol Robotic Network sites in Korea. The study periods were between 2004 and 2007 at Anmyon and between 2003 and 2011 at Gosan, when both PM_(10) and AOD were available. Mean PM_(10) when AOD was available(PM AOD) was higher than that from all PM_(10)data(PM all) by 5.1 and9.9 μg/m~3 at Anmyon and Gosan, which accounted for 11% and 26% of PM all, respectively.Because of a difference between mean PM_(10) under daytime clear-sky conditions(PM clear)and PM AOD, the variations in ΔPM_(10), the difference of PM all from PM clear rather than from PM AOD, were investigated. Although monthly variations in ΔPM_(10)at the two sites were different, they were positively correlated to those in ΔT, similarly defined as ΔPM_(10)except for temperature, at both sites. ΔPM_(10)at Anmyon decreased to a negative value in January due to an influence of the Siberian continental high-pressure system while ΔPM_(10)at Gosan was high in winter due to an effect of photochemical production at higher temperatures than at Anmyon.     

燃煤电厂烟塔合一排烟风洞试验与数值模拟对比分析

近年来,燃煤电厂烟塔合一烟气排烟对近距离环境影响的不确定性,使其在国内的推广过程受到一定限制。准确判断烟塔合一排烟的环境影响,对于我国现有燃煤电厂烟气污染物的排放有着巨大的工程价值和明显的现实意义。利用国家环境保护某重点实验室中风洞试验平台,对燃煤电厂烟塔合一烟气污染物在近距离的扩散和传输行为,进行物理风洞试验以及数值模拟计算,并进行对比分析。结果表明:德国Austal2000模式的浓度预测并不精确;数值风洞也有其差异性,而物理风洞的结果在很大程度上符合现有的理论及国内工程实际。     

风电场对米波雷达系统的影响研究

目的针对目前风电场对米波雷达的潜在威胁,研究风电场的有源干扰、无源散射、遮蔽对米波雷达系统的影响,为评估风电场对米波雷达系统的影响提供技术指导。方法根据风力发电机的工作原理和结构,对风电场的有源干扰进行实际测试,就风电场有源干扰对米波雷达系统周边背景噪声的影响进行分析,提出一系列应对有源干扰的措施;利用散射、刃峰绕射、多普勒效应等理论,就无源散射、遮蔽等因素对米波雷达系统的影响进行仿真计算和分析。结果风电场将引起米波雷达系统周边背景噪声恶化、虚警率提高、探测距离缩减、测向和测速误差等,导致米波雷达性能下降。结论风电场对米波雷达系统存在着巨大威胁,在米波雷达台站附近规划建设风电场前应进行严格的技术评估,保证国家经济建设和雷达系统性能不受影响。     

一种低功耗高性能数据采集数字处理平台的设计

目的构建一套基于中频信号基带数字信号处理的软件无线电平台。方法通过选择芯片设计硬件电路设计出合适的PCB板。结果主要依据软件无线电平台,提出了一种基于A/D+FPGA+D/A的硬件设计方案,该系统包括了前端的A/D数据采集和后端的D/A模拟数据恢复的详细收发电路原理设计。结论构建了一个从前端数据接收到后端模拟发送的高速基带数字信号处理平台。     

热带海洋大气环境下X70管线钢的缝隙腐蚀行为研究

目的研究X70管线钢在热带海洋大气实海环境下的缝隙腐蚀行为。方法在距离湛江东海岛海岸50m和200 m处分别搭建楔型缝隙模型,安装大气环境Cl-收集装置和自动气象监测站。结果距离海岸越近,风速越大,大气中Cl-沉降速率也越大,X70管线钢缝隙腐蚀越严重。X70管线钢在距离海岸50 m处发生缝隙腐蚀的最大缝宽约为0.96 mm,200 m处最大缝宽约为3.75 mm,50 m处缝隙腐蚀更严重。结论缝隙腐蚀区域形成了氧浓差电池,同时随着缝隙液中Cl-向缝隙内迁移,发生闭塞区电池自催化过程,在二者共同作用下,缝隙腐蚀区域较非缝隙腐蚀区域腐蚀更严重。     

极低风速条件下水-气界面甲烷气体传输速率分析

薄边界层理论被广为用来计算水-气界面气体通量,而气体传输速率(k600)则是其中的关键性环境因子.为了研究极低风速下小型浅水湿地水-气界面甲烷气体传输速率,以宜昌饮用水水库梅子垭水库和周邻5个富营养化池塘为研究对象,采用静态通量箱进行了为期一年的水-气界面甲烷气体通量观测,同步监测了水环境因子和气象因子.野外监测时的风速(U10)范围为0~0.75 m·s~(-1),平均值约为0.19 m·s~(-1);水温(Tw)变化范围为6.3~30.9℃,平均值约为19.3℃.结果表明,梅子垭水库和周边5个池塘水-气界面甲烷气体传输速率较小,在0.20~1.99 cm·h~(-1)之间变化,平均值约为0.50 cm·h~(-1).本研究利用表层水温和风速指标两个参数的双二次项模型和二次项加幂函数模型,回归得到了气体传输速率的数学公式,回归结果与原始数据和对k600进行深度平均(bin-averaged)后的数据均存在极显著性关系.     

Modulation-assisted high speed machining of compacted graphite iron (CGI)

The application of controlled, low-frequency modulation (～100 Hz) superimposed onto the cutting process in the feed-direction – modulation-assisted machining (MAM) – is shown to be quite effective in reducing the wear of cubic boron nitride (CBN) tools when machining compacted graphite iron (CGI) at high machining speeds (>500 m/min). The tool life is at least 20 times greater than in conventional machining. This significant reduction in wear is a consequence of the multiple effects realized by MAM, including periodic disruption of the tool–workpiece contact, formation of discrete chips, enhanced fluid action and lower cutting temperatures. The propensity for thermochemical wear of CBN, the principal wear mode at high speeds in CGI machining, is thus reduced. The tool wear in MAM is also found to be smaller at the higher cutting speeds (730 m/min) tested. The feed-direction MAM appears feasible for implementation in industrial machining applications involving high speeds.     

气象条件对上甸子地区气溶胶散射特征的影响

利用北京地区上甸子站气溶胶散射系数、PM2.5质量浓度和气象要素1 a的观测资料,研究不同天气条件下上甸子地区散射系数的变化特征,并讨论了气象条件对散射系数的影响.结果表明,散射系数在雾霾天最高608.4 Mm-1,其次为雾天500.6 Mm-1和霾天423.7 Mm-1,是一般天气散射系数的6.4～9.2倍.在各类天...