模糊综合评价法在钢铁企业安全投资合理性评价中的应用

为了对钢铁企业安全投资进行模糊综合评价,建立了钢铁企业安全投资的评价体系,确定各因素的权重。得出模糊综合评价矩阵,可对各因素进行评价分析;得出某钢铁企业安全投资现状分数为83.9分,等级为较好,需着重加强安全培训、劳保品、工业卫生等人因素方面的投资;在环境方面的投资较合理。     

氨基改性生物炭负载纳米零价铁去除水中Cr(VI)

以聚乙烯亚胺（PEI）为功能单体,玉米秸秆生物炭为载体,制备了氨基改性生物炭负载型纳米零价铁（nZVI@PEI-HBC）,并利用扫描电镜（SEM）、红外光谱（FTIR）和X射线光电子能谱（XPS）等手段对材料进行了表征,分析了溶液pH、温度、材料投加量等因素对其去除Cr（VI）的影响及其去除机理.结果表明：在投加量为0.5 g·L^-1,温度为20℃,pH值为5,Cr（VI）初始浓度为20 mg·L^-1条件下,各材料对Cr（VI）的去除率大小为nZVI@PEI-HBC > nZVI > PEI-HBC > HBC.SEM显示nZVI颗粒较均匀地分散在生物炭表面,FTIR分析表明PEI改性后材料表面增加了氨基等重金属配位基团,这可能是nZVI@PEI-HBC去除Cr（VI）效果更好的原因.影响因素研究表明,材料具有较好稳定性,老化28 d后其Cr（VI）去除性能变化不大;酸性环境、升温、增大材料投加量均有利于nZVI@PEI-HBC对Cr（VI）的去除.机理研究发现,水中溶解氧加速了nZVI的腐蚀和Fe（II）的释放,促进Cr（VI）还原为Cr（III）,然后通过共沉淀作用和氨基等基团的吸附作用被去除.     

AMD铁絮体改性生物炭对重金属吸附机理研究 ——以Pb(II)为例

以酸性矿山废水生成的铁絮体和秸秆生物炭为原料,采用化学改性和紫外辐射联用技术制备改性生物炭,并通过正交试验确定最佳改性条件,同时利用FTIR、SEM和BET等方法对吸附材料的形貌特征、孔隙结构及其表面化学性质进行表征.结果表明,通过改性使吸附材料比表面积增大,吸附位点增多,在25℃、pH为7时,吸附材料改性后比表面积为295.71 m²·g^-1,对Pb（II）的拟合吸附量可达278 mg·g^-1.改性材料对Pb（II）的吸附过程符合Langmuir吸附等温线模型和准二级动力学模型,主要为单分子层吸附,受化学吸附控制.     

色氨酸对生物成因铁硫酸盐次生矿物形成的影响

采用氧化亚铁硫杆菌催化合成铁硫酸盐次生矿物,研究不同L-色氨酸添加浓度对矿物合成体系pH、氧化还原电位（ORP）、Fe²⁺氧化率、总Fe沉淀率,以及次生矿物产量、化学组成及矿物相的影响.结果表明,随着体系色氨酸浓度的增加,pH降低幅度越小,ORP上升越不明显.色氨酸对铁硫酸盐次生矿物合成的影响依赖于其浓度,当色氨酸浓度低于1.67 g·L^-1时,色氨酸对铁硫酸盐次生矿物的形成起促进作用,表现为总Fe沉淀率及矿物产量随着色氨酸浓度升高而增加.而当色氨酸浓度升高至6.67 g·L^-1时,Fe²⁺氧化率、总Fe沉淀率和矿物产量远低于对照组,表明高浓度色氨酸会抑制铁硫酸盐次生矿物的形成.次生矿物内Fe/S比介于施氏矿物和黄钾铁矾的理论值之间,表明不同合成体系所得次生矿物均为黄钾铁矾和施氏矿物的混合物.矿物学特征分析表明,随着色氨酸浓度的升高,矿物的合成表现为黄钾铁矾向施氏矿物转移.     

Long-term effects of silver nanoparticles on performance of phosphorus removal in a laboratory-scale vertical flow constructed wetland

Silver nanoparticles(AgNPs) have been widely used in many fields,which raised concerns about potential threats to biological sewage treatment systems.In this study,the phosphorus removal performance,enzymatic activity and microbial population dynamics in constructed wetlands(CWs) were evaluated under a long-term exposure to Ag NPs(0,50,and 200 μg/L) for 450 days.Results have shown that Ag NPs inhibited the phosphorus removal efficiency in a short-term exposure,whereas caused no obviously negative effects from a long-term perspective.Moreover,in the coexisting CW system of Ag NPs and phosphorus,competition exhibited in the initial exposure phase,however,cooperation between them was observed in later phase.Enzymatic activity of acid-phosphatase at the moderate temperature(10–20°C) was visibly higher than that at the high temperature(20–30℃) and CWs with Ag NPs addition had no appreciable differences compared with the control.High-throughput sequencing results indicated that the microbial richness,diversity and composition of CWs were distinctly affected with the extension of exposure time at different Ag NPs levels.However,the phosphorus removal performance of CWs did not decline with the decrease of polyphosphate accumulating organisms(PAOs),which also confirmed that adsorption precipitation was the main way of phosphorus removal in CWs.The study suggested that Ag NPs and phosphorus could be removed synergistically in the coexistence system.This work has some reference for evaluating the influences of Ag NPs on the phosphorus removal and the interrelation between them in CWs.     

不同浓度锌处理下水稻幼苗对镉的累积效应

为探究锌（Zn）对水稻镉（Cd）累积的影响及其根表铁膜所发挥的作用,选取Cd高累积型水稻品种中9优547（简称"Z547"）和Cd低累积型水稻品种金优402（简称"J402"）,采用温室水培试验,研究0、2、5、10、15和20 μmol/L等6个Zn浓度下水稻幼苗对Cd的累积效应,以及不同浓度Zn处理对根表铁膜生成量的影响.结果表明:①随着c（Zn）的增加,Z547和J402水稻幼苗生物量均呈先增后减的趋势,分别在c（Zn）为2和10 μmol/L时达到最大值.②Z547和J402水稻幼苗中w（Cd）均呈先降后增的趋势,分别在c（Zn）为5和2 μmol/L时达到最小值;当水稻幼苗中w（Cd）达到最小值时,Z547根和地上部中w（Cd）分别为31.65和11.47 mg/kg,J402根和地上部中w（Cd）分别为22.58和14.36 mg/kg.③不同浓度Zn处理下水稻幼苗各部位中w（Cd）均与根表铁膜中w（Mn）、w（Fe）、w（Fe+Mn）呈显著正相关,高铁膜处理水稻幼苗中w（Cd）显著高于低铁膜处理,表明根表铁膜生成量的增加会促进Cd在水稻幼苗中的累积.研究显示,当c（Zn）较低时,c（Zn）的增加会抑制水稻幼苗对Cd的累积;当c（Zn）较高时,c（Zn）的增加会促进水稻幼苗对Cd的累积,而Zn可通过控制根表铁膜的生成来影响水稻幼苗对Cd的累积.      

电化学微传感器检测水中痕量铜离子

为改善微电极在阳极溶出伏安法检测重金属离子过程中低电流响应和低电催化能力的缺点,提出了一种在碳纤维微电极表面合成还原氧化石墨烯/纳米金材料制得还原氧化石墨烯纳米金修饰碳纤维微电极（rGO/AuNPs CFMEs）的方法.通过SEM表征,所制备的rGO/AuNPs CFMEs具有比表面积高、吸附能力强和催化活性好的特点,因此改性微电极适合作为方波阳极溶出伏安法（SWASV）测定水中铜离子（Cu²⁺）的工作电极.在构建微传感器测试水中痕量铜离子系统后,对pH值、电导率、富集时间和富集电位等检测条件进行了优化.在pH值为4,电导率为36.1S/m,富集时间为360s,富集电位为-1.2V的最佳条件下,铜的线性范围和检出限分别0~1.0μmol/L和2.4nmol/L.此外,微传感器的可重复性、长期稳定性以及选择性也得到了验证.     

Pt负载暴露(001)晶面Bi2WO6催化剂合成及光催化性能

通过水热法制备了暴露（001）晶面的Bi₂WO₆纳米片,利用光还原法将Pt纳米颗粒负载于其表面.选择苯甲醇氧化和罗丹明B（RhB）降解为探针反应,评价了催化剂的光催化性能.在苯甲醇氧化实验中,Pt负载暴露001晶面的Bi₂WO₆样品的苯甲醇转化率为20.7%,约为未负载样品的2倍.在RhB降解实验中,Pt负载样品在光照40min后对RhB的矿化率可达81.1%,而未负载样品RhB矿化率仅为55.8%,表明Pt负载样品具有更优的降解速率和矿化能力.催化剂性能的提升归因于高能晶面暴露和Pt负载的协同作用.Pt纳米颗粒的负载作为助催化剂增加了催化剂表面的活性位点,同时提高了晶面光生电子空穴对的分离和迁移效率.     

Nanoencapsulation of hexavalent chromium with nanoscale zero-valent iron: High resolution chemical mapping of the passivation layer

Solid phase reactions of Cr(Ⅵ) with Fe(0) were investigated with spherical-aberration-corrected scanning transmission electron microscopy(Cs-STEM) integrated with X-ray energy-dispersive spectroscopy(XEDS). Near-atomic resolution elemental mappings of Cr(Ⅵ)–Fe(0) reactions were acquired. Experimental results show that rate and extent of Cr(Ⅵ) encapsulation are strongly dependent on the initial concentration of Cr(Ⅵ) in solution. Low Cr loading in nZⅥ(1.0 wt%) promotes the electrochemical oxidation and continuous corrosion of n ZⅥ while high Cr loading(1.0 wt%) can quickly shut down the Cr uptake. With the progress of iron oxidation and dissolution, elements of Cr and O counter-diffuse into the nanoparticles and accumulate in the core region at low levels of Cr(Ⅵ)(e.g., 10 mg/L). Whereas the reacted n ZⅥ is quickly coated with a newly-formed layer of 2–4 nm in the presence of concentrated Cr(Ⅵ)(e.g., 100 mg/L). The passivation structure is stable over a wide range of pH unless pH is low enough to dissolve the passivation layer. X-ray photoelectron spectroscopy(XPS) depth profiling reconfirms that the composition of the newly-formed surface layer consists of Fe(Ⅲ)–Cr(Ⅲ)(oxy)hydroxides with Cr(Ⅵ) adsorbed on the outside surface. The insoluble and insulating Fe(Ⅲ)–Cr(Ⅲ)(oxy)hydroxide layer can completely cover the n ZⅥ surface above the critical Cr loading and shield the electron transfer. Thus, the fast passivation of nZⅥ in high Cr(Ⅵ) solution is detrimental to the performance of nZⅥ for Cr(Ⅵ) treatment and remediation.     

Long-term effects of environmentally relevant concentrations of silver nanoparticles on microbial biomass, enzyme activity, and functional genes involved in the nitrogen cycle of loamy soil

The increasing production and use of engineered silver nanoparticles (AgNP) in industry and private households are leading to increased concentrations of AgNP in the environment. An ecological risk assessment of AgNP is needed, but it requires understanding the long term effects of environmentally relevant concentrations of AgNP on the soil microbiome. Hence, the aim of this study was to reveal the long-term effects of AgNP on soil microorganisms. The study was conducted as a laboratory incubation experiment over a period of one year using a loamy soil and AgNP concentrations ranging from 0.01 to 1?mg?AgNP/kg soil. The short term effects of AgNP were, in general, limited. However, after one year of exposure to 0.01?mg?AgNP/kg, there were significant negative effects on soil microbial biomass (quantified by extractable DNA; p?=?0.000) and bacterial ammonia oxidizers (quantified by amoA gene copy numbers; p?=?0.009). Furthermore, the tested AgNP concentrations significantly decreased the soil microbial biomass, the leucine aminopeptidase activity (quantified by substrate turnover; p?=?0.014), and the abundance of nitrogen fixing microorganisms (quantified by nifH gene copy numbers; p?=?0.001). The results of the positive control with AgNO3 revealed predominantly stronger effects due to Ag⁺ ion release. Thus, the increasing toxicity of AgNP during the test period may reflect the long-term release of Ag⁺ ions. Nevertheless, even very low concentrations of AgNP caused disadvantages for the microbial soil community, especially for nitrogen cycling, and our results confirmed the risks of releasing AgNP into the environment.