Effect of platinum on the photocatalytic degradation of chlorinated organic compound

TiO2 nanoparticles, doped with di erent Pt contents, were prepared by a modified photodeposition method using Degussa P-25 TiO2, H2PtCl6 6H2O and methanol as the solvents. The physicochemical properties of Pt/TiO2 were investigated by the nitrogen adsorption and desorption isotherm measurement technique, X-ray di raction analysis and photoluminescence spectra, respectively. Reaction rates from photocatalytic removal of dichloromethane over Degussa P-25 TiO2 and Pt/TiO2 were evaluated. The average diameter and BET surface area of the TiO2 catalyst particles were 300 nm and 50 m2/g, respectively. The degradation e ciency was 99.0%, 82.7%, 55.2%, and 57.9% with TiO2 at inlet concentrations of 50, 100, 200, and 300 ppm, respectively. And the degradation e ciency was 99.3%, 79.7%, 76.5%, and 73.4% with a 0.005 wt.% Pt/TiO2 at inlet concentrations of 50, 100, 200, and 300 ppm, respectively. In addition, we found that the photoluminescence emission peak intensities decreased with increases in the doping amount of Pt, which indicates that the irradiative recombination was weakened. Furthermore, the results showed that the UV/0.005 wt.% Pt/TiO2 process was capable of e ciently decomposing gaseous DCM in air.     

Reversibly enhanced aqueous solubilization of volatile organic compounds using a redox-reversible surfactant

Surfactant-enhanced remediation (SER) is an effective method for the removal of volatile organic compounds (VOCs) from contaminated soils and groundwater. To reuse the surfactant the VOCs must be separated from the surfactant solutions. The water solubility of VOCs can be enhanced using reversible surfactants with a redox-acive group, (ferrocenylmethyl)dodecyldimethylammonium bromide (Fcl2) and (ferrocenylmethyl)tetradecanedimethylammonium bromide (Fcl4), above and below their critical micelle concentrations (CMC) under reducing (I⁺) and oxidative (I²⁺) conditions. The CMC values of Fcl2 and Fcl4 in I⁺ are 0.94 and 0.56 mmol/L and the solubilization of toluene by Fcl2 and Fcl4 in I⁺ for toluene is higher than the solubilization achieved with sodium dodecyl sulfate, cetyltrimethylammonium bromide and Trition X-114. The solubilization capacity of the ferrocenyl surfactants for each tested VOCs ranked as follows: ethylbenzene > toluene > benzene. The solubilities of VOCs by reversible surfactant in I⁺ were 30% higher than those in I²⁺ at comparable surfactant concentrations. The effects of Fcl4 concentrations on VOCs removal efficiency were as follows: benzene > toluene > ethylbenzene. However, an improved removal efficiency was achieved at low ferrocenyl surfactant concentrations. Furthermore, the reversible surfactant could be recycled through chemical approaches to remove organic pollutants, which could significantly reduce the operating costs of SER technology.     

低温等离子体-催化协同降解挥发性有机废气

低温等离子体-催化协同技术适合于各类挥发性有机物的治理,特别是大气量低浓度的有机废气的处理.高效催化剂的加入可 以显著提高等离子体反应中有机废气的降解效率,减少有害副产物的生成以及提高反应器的能量利用率.从反应器、催化剂以及背景气体等方面探讨了该技术实现产业化需要解决的问题,结合低温等离子体与催化剂的相互作用、等离子体...     

岩溶地下河系统中有机氯的分布特征与来源分析

选取重庆老龙洞、青木关岩溶地下河为研究对象,采用气相色谱仪-微池电子捕获检测器(GC-μECD)分析两条地下河水体中21种有机氯农药(OCPs)的浓度.结果表明,南山地下河中六六六(HCHs)和艾氏剂类化合物(ALDs)是主要检出物,青木关地下河中HCHs和甲氧滴滴涕是主要检出物.南山、青木关地下河中均未检出o,p'-DDE、p,p'-DDE、o,p'-DDD,同时,青木关地下河还未检出o,p'-DDT、狄氏剂,其余OCPs在两条地下河中检出率高达100%.青木关地下河中OCPs浓度范围为145~278 ng·L-1之间,平均值为213 ng·L-1;南山老龙洞地下河中OCPs浓度介于17.7~40.8 ng·L-1之间,平均值为32.7ng·L-1.两条地下河中各OCPs组分表现为地下河出口大于入口.通过对OCPs污染来源分析,发现两地下河流域滴滴涕(DDTs)主要来自于历史上工业DDTs输入,氯丹主要来自于大气沉降.六六六(HCHs)主要来源是林丹的输入,南山地下河属于历史污染,青木关地下河上游的甘家槽有新的HCHs输入.与国内外其他各水体相比,南山地下河水体中HCHs、DDTs浓度处于低水平;青木关下河处于中等偏高水平.结合中外用水卫生标准,发现南山地下河和青木关地下河未超过饮水安全标准.青木关应禁止农田施用有机氯农药,保护地下河生态环境.     

Effects of metal and acidic sites on the reaction by-products of butyl acetate oxidation over palladium-based catalysts

Catalytic oxidation is widely used in pollution control technology to remove volatile organic compounds. In this study, Pd/ZSM-5 catalysts with different Pd contents and acidic sites were prepared via the impregnation method. All the catalysts were characterized by means of N2 adsorption- desorption, X-ray fluorescence （XRF）, HE temperature programmed reduction （H2-TPR）, and NH3 temperature programmed desorption （NH3-TPD）. Their catalytic performance was investigated in the oxidation of butyl acetate experiments. The by-products of the reaction were collected in thermal desorption tubes and identified by gas chromatography/mass spectrometry. It was found that the increase of Pd content slightly changed the catalytic activity of butyl acetate oxidation according to the yield of CO2 achieved at 90%, but decreased the cracking by-products, whereas the enhancement of strong acidity over Pd-based catalysts enriched the by-product species. The butyl acetate oxidation process involves a series of reaction steps including protolysis, dehydrogenation, dehydration, cracking, and isomerization. Generally, butyl acetate was cracked to acetic acid and 2- methylpropene and the latter was an intermediate of the other by-products, and the oxidation routes of typical by-products were proposed. Trace amounts of 3-methylpentane, hexane, 2-methylpentane, pentane, and 2-methylbutane originated from iso4merization and protolysis reactions.     

Unregulated emissions from diesel engine with particulate filter using Fe-based fuel borne catalyst

The alteration and formation of toxic compounds and potential changes in the toxicity of emissions when using after-treatment technologies have gained wide attention. Volatile organic compound（VOC）, carbonyl compound and particle-phase polycyclic aromatic hydrocarbon（PAH） emissions were tested at European Steady State Cycle（ESC） to study unregulated emissions from a diesel engine with a fuel-borne catalyst and diesel particulate filter（FBC–DPF）. An Fe-based fuel-borne catalyst was used for this study. According to the results, brake specific emissions of total VOCs without and with DPF were 4.7 and4.9 mg/kWh, respectively, showing a 4.3% increase. Benzene and n-undecane emissions increased and toluene emission decreased, while other individual VOC emissions basically had no change. When retrofitted with the FBC–DPF, total carbonyl compound emission decreased 15.7%, from 25.8 to 21.8 mg/kWh. The two highest carbonyls, formaldehyde and acetaldehyde, were reduced from 20.0 and 3.7 to 16.5 and 3.3 mg/kWh respectively. The specific reactivity（SR） with DPF was reduced from 6.68 to 6.64 mg/kWh. Total particle-phase PAH emissions decreased 66.4% with DPF compared to that without DPF. However, the Benzo[a]pyrene equivalent（BaPeq） with DPF had increased from 0.016 to 0.030 mg/kWh.Fluoranthene and Pyrene had the greatest decrease, 91.1% and 88.4% respectively. The increase of two- and three-ring PAHs with DPF indicates that the fuel-borne catalyst caused some gas-phase PAHs to adsorb on particles. The results of this study expand the knowledge of the effects of using a particulate filter and a Fe-based fuel-borne catalyst on diesel engine unregulated emissions.     

Fast increasing of surface ozone concentrations in Pearl River Delta characterized by a regional air quality monitoring network during 2006-2011

Based on the observation by a Regional Air Quality Monitoring Network including 16 monitoring stations, temporal and spatial variations of ozone(O3), NO2and total oxidant(Ox) were analyzed by both linear regression and cluster analysis. A fast increase of regional O3concentrations of 0.86 ppbV/yr was found for the annual averaged values from 2006 to 2011 in Guangdong, China. Such fast O3increase is accompanied by a correspondingly fast NOx reduction as indicated by a fast NO2 reduction rate of 0.61 ppbV/yr. Based on a cluster analysis, the monitoring stations were classified into two major categories – rural stations(non-urban) and suburban/urban stations. The O3concentrations at rural stations were relatively conserved while those at suburban/urban stations showed a fast increase rate of 2.0 ppbV/yr accompanied by a NO2 reduction rate of 1.2 ppbV/yr. Moreover, a rapid increase of the averaged O3 concentrations in springtime(13%/yr referred to 2006 level) was observed, which may result from the increase of solar duration, reduction of precipitation in Guangdong and transport from Eastern Central China. Application of smog production algorithm showed that the photochemical O3production is mainly volatile organic compounds(VOC)-controlled. However, the photochemical O3production is sensitive to both NOx and VOC for O3pollution episode. Accordingly, it is expected that a combined NOx and VOC reduction will be helpful for the reduction of the O3 pollution episodes in Pearl River Delta while stringent VOC emission control is in general required for the regional O3 pollution control.     

Effect of a high strength chemical industry wastewater on microbial community dynamics and mesophilic methane generation

A high strength chemical industry wastewater was assessed for its impact on anaerobic microbial com- munity dynamics and consequently mesophilic methane generation. Cumulative methane production was 251 mL/g total chemical oxygen demand removed at standard temperature and pressure at the end of 30 days experimental period with a highest recorded methane percentage of 80.6% of total biogas volume. Volatile fatty acids （VFAs） analysis revealed that acetic acid was the major intermediate VFAs produced with propionic acid accumulating over the experimental period. Quantitative analysis of microbial communities in the test and control groups with quantitative real time polymerase chain reaction highlighted that in the test group, Eubacteria （96.3%） was dominant in comparison with methanogens （3.7%）. The latter were dominated by Methanomicrobiales and Methanobacteriales while in test groups increased over the experimental period, reaching a maximum on day 30. Denaturing gradient gel electrophoresis profile was performed, targeting the 16S rRNA gene of Eubacteria and Archaea, with the DNA samples extracted at 3 different time points from the test groups. A phylogenetic tree was constructed for the sequences using the neighborhood joining method. The analysis revealed that the presence of organisms resembling Syntrophomonadaceae could have contributed to increased production of acetic and propionic acid intermediates while decrease of organisms resembling Pelotomaculum sp. could have most likely contributed to accumulation of propionic acid. This study suggested that the degradation of organic components within the high strength industrial wastewater is closely linked with the activity of certain niche microbial communities within eubacteria and methanogens.     

江苏省人为源挥发性有机物排放清单

掌握VOCs排放特征是研究区域大气复合污染特征和控制策略的前提.对江苏省VOCs人为源进行系统分类,收集活动水平数据,应用国内外排放因子研究成果及江苏省行业调研结果,采用排放因子法建立了江苏省2010年分行业、分城市的人为源VOCs排放清单.结果表明:江苏省人为源VOCs排放总量约为179.20×104t,其中化石燃料燃烧源、生物质燃烧源、工业过程源、溶剂使用源、移动源、油品储运源的排放量分别占排放总量的24.1%、3.3%、22.3%、25.3%、18.4%和6.6%,工业过程源中石油炼制、有机化工、医药制造是重点行业,溶剂使用源中机械装备制造、电子设备制造是重点行业.南京、苏州、无锡、常州、南通5个苏南城市VOCs排放量明显高于苏北和苏中地区,占全省总排放量的60.0%,苏州、南京、无锡排放量居前3位.各城市化石燃料燃烧源和移动源排放所占比例均超过10.0%,其他重点行业差异显著,其中南京市为石油炼制、有机化工,苏州市为有机化工、机械涂装,无锡市为有机化工、电子设备制造.     

新型IC反应器在山梨醇废水处理中的工程应用

将布水装置优化后的新型内循环(IC)反应器应用于某山梨醇生产企业实际废水的二级厌氧生化处理,获得了较好的处理效果。调试阶段的结果表明:经过IC反应器的处理后,废水COD浓度由处理前的2 374~4 967 mg/L降至301~823 mg/L,COD去除率达81.4%~91.2%,COD容积负荷达8.1~13.7 kg/(m3·d);总体来说,当水力负荷增大时,COD容积负荷也相应增大;IC反应器的出水挥发性脂肪酸(VFA)基本控制在200 mg/L以下;厌氧出水再依次经过接触氧化池和絮凝沉淀池等配套工艺的处理后,COD降至80 mg/L以下,实现达标排放。